Question about Toyota Cars & Trucks

1 Answer

Lower front pulley replacement - Toyota Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 3,679 Answers

What vehicle is it ?

Posted on May 08, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whistling drive belts. I have used belt dressing; it hasn't worked. How to change the belts?


All Mitsubishi cars pretty much hide the water pump under the timing belt. You should buy all new belts for the car and if you have 150,000+ miles consider replacing the water pump at the same time.
You will have to take off the power steering belt .
First , take off the negative battery cable so you do not blow an expensive fuse on the positive battery cable clamp. Facing the back of the car , reach UNDER the alternator and loosen the bolt on the bottom right side, now loosen the bolt on the adjuster block on top, you can now turn the adjuster bolt and move the alternator to change the belt.
To take off the steering pump belt on the front of the motor, you need to loosen the nut on the back side of the pulley it holds the adjuster pulley in place . With the adjuster pulley loose , you can use the adjuster bolt to move the pulley to adjust the steering pump belt.
Now take off the upper belt cover, support the motor, take off the motor mount, jack up the right front corner of the car, take off the front right tire, take off the engine plastic under cover.
Line up the TDC timing mark on the cover to the mark on the pulley, check that the dot on the cam lines up with the timing arrow on the head, take off the lower pulleys,
take off the lower engine cover, observe the timing marks/arrows and highlight with paint (crank marks and cam marks should all line up if not , put the lower cover and pulley back on and rotate the crankshaft one full turn.), loosen the timing belt tensioner pulley ,take off the timing belt, counter balancer belt if there is one. Now you can unbolt the water pump, scrape the gasket, and replace it.
The good news is, if you have tools,a compressor, an air gun (for lower pulley bolt), patience , and four to eight hours to kill, you can actually save money and do it your self.

May 14, 2011 | 2002 Mitsubishi Galant

1 Answer

How to replace a timing belt on a 1989 galant


All Mitsubishi cars pretty much hide the water pump under the timing belt. You should buy all new belts for the car and if you have 150,000+ miles consider replacing the water pump at the same time.
You will have to take off the power steering belt .
First , take off the negative battery cable so you do not blow an expensive fuse on the positive battery cable clamp. Facing the back of the car , reach UNDER the alternator and loosen the bolt on the bottom right side, now loosen the bolt on the adjuster block on top, you can now turn the adjuster bolt and move the alternator to change the belt.
To take off the steering pump belt on the front of the motor, you need to loosen the nut on the back side of the pulley it holds the adjuster pulley in place . With the adjuster pulley loose , you can use the adjuster bolt to move the pulley to adjust the steering pump belt.
Now take off the upper belt cover, support the motor, take off the motor mount, jack up the right front corner of the car, take off the front right tire, take off the engine plastic under cover.
Line up the TDC timing mark on the cover to the mark on the pulley, take off the lower pulleys,
take off the lower engine cover, observe the timing marks/arrows and highlight with paint (crank marks and cam marks should all line up if not , rotate the crankshaft one full turn.), loosen the timing belt tensioner pulley ,take off the timing belt, counter balancer belt if there is one. Now you can unbolt the water pump, scrape the gasket, and replace it.
The good news is, if you have tools,a compressor, an air gun(for lower pulley bolt), patience , and four to eight hours to kill, you can actually save money and do it your self.

Mar 07, 2011 | 1989 Mitsubishi Galant

1 Answer

Lancer rally timing belt service manual


You do not really need a manual to change the belts. All Mitsubishi cars pretty much hide the water pump under the timing belt. You should buy all new belts for the car and if you have 150,000+ miles consider replacing the water pump at the same time.
You will have to take off the power steering belt .
First , take off the negative battery cable so you do not blow an expensive fuse on the positive battery cable clamp. Facing the back of the car , reach UNDER the alternator and loosen the bolt on the bottom right side, now loosen the bolt on the adjuster block on top, you can now turn the adjuster bolt and move the alternator to change the belt.
To take off the steering pump belt on the front of the motor, you need to loosen the nut on the back side of the pulley it holds the adjuster pulley in place . With the adjuster pulley loose , you can use the adjuster bolt to move the pulley to adjust the steering pump belt.
Now take off the upper belt cover, support the motor, take off the motor mount, jack up the right front corner of the car, take off the front right tire, take off the engine plastic under cover.
Line up the TDC timing mark on the cover to the mark on the pulley, take off the lower pulleys,
take off the lower engine cover, observe the timing marks/arrows and highlight with paint (crank marks and cam marks should all line up if not , rotate the crankshaft one full turn.), loosen the timing belt tensioner pulley ,take off the timing belt, counter balancer belt if there is one. Now you can unbolt the water pump, scrape the gasket, and replace it.
The good news is, if you have tools,a compressor, an air gun(for lower pulley bolt), patience , and four to eight hours to kill, you can actually save money and do it your self.

Jan 22, 2011 | 2006 Mitsubishi Lancer

1 Answer

Need a diagram of how to replace timing belt


All Mitsubishi cars pretty much hide the water pump under the timing belt. You should buy all new belts for the car and if you have 150,000+ miles consider replacing the water pump at the same time.
You will have to take off the power steering belt .
First , take off the negative battery cable so you do not blow an expensive fuse on the positive battery cable clamp. Facing the back of the car , reach UNDER the alternator and loosen the bolt on the bottom right side, now loosen the bolt on the adjuster block on top, you can now turn the adjuster bolt and move the alternator to change the belt.
To take off the steering pump belt on the front of the motor, you need to loosen the nut on the back side of the pulley it holds the adjuster pulley in place . With the adjuster pulley loose , you can use the adjuster bolt to move the pulley to adjust the steering pump belt.
Now take off the upper belt cover, support the motor, take off the motor mount, jack up the right front corner of the car, take off the front right tire, take off the engine plastic under cover.
Line up the TDC timing mark on the cover to the mark on the pulley, check that the dot on the cam lines up with the timing arrow on the head, take off the lower pulleys,
take off the lower engine cover, observe the timing marks/arrows and highlight with paint (crank marks and cam marks should all line up if not , put the lower cover and pulley back on and rotate the crankshaft one full turn.), loosen the timing belt tensioner pulley ,take off the timing belt, counter balancer belt if there is one. Now you can unbolt the water pump, scrape the gasket, and replace it.
The good news is, if you have tools,a compressor, an air gun (for lower pulley bolt), patience , and four to eight hours to kill, you can actually save money and do it your self.

Jan 05, 2011 | 2003 Mitsubishi Lancer

1 Answer

How to change belts 2003 mitsubishi galant


All Mitsubishi cars pretty much hide the water pump under the timing belt. You should buy all new belts for the car and if you have 150,000+ miles consider replacing the water pump at the same time.
You will have to take off the power steering belt .
First , take off the negative battery cable so you do not blow an expensive fuse on the positive battery cable clamp. Facing the back of the car , reach UNDER the alternator and loosen the bolt on the bottom right side, now loosen the bolt on the adjuster block on top, you can now turn the adjuster bolt and move the alternator to change the belt.
To take off the steering pump belt on the front of the motor, you need to loosen the nut on the back side of the pulley it holds the adjuster pulley in place . With the adjuster pulley loose , you can use the adjuster bolt to move the pulley to adjust the steering pump belt.
Now take off the upper belt cover, support the motor, take off the motor mount, jack up the right front corner of the car, take off the front right tire, take off the engine plastic under cover.
Line up the TDC timing mark on the cover to the mark on the pulley, take off the lower pulleys,
take off the lower engine cover, observe the timing marks/arrows and highlight with paint (crank marks and cam marks should all line up if not , rotate the crankshaft one full turn.), loosen the timing belt tensioner pulley ,take off the timing belt, counter balancer belt if there is one. Now you can unbolt the water pump, scrape the gasket, and replace it.
The good news is, if you have tools,a compressor, an air gun(for lower pulley bolt), patience , and four to eight hours to kill, you can actually save money and do it your self.

Nov 14, 2010 | 2003 Mitsubishi Galant

1 Answer

Timing marks on a 2000 volvo v40 1.9t crank and cam marks


Timing belt alignment markings


9c6ff12.gif

Here is all the tech info for removing and replacing....hope this helps you:

4-Cylinder Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Right hand engine cover
    • Cover over the right headlamp
    • Accessory drive belt
    • Front timing cover
    • Servo reservoir
  3. Position Volvo lifting beam 999 5006 or equivalent slightly in front of the front lifting eyelet for the engine. Use Volvo lifting arm 999 5383 or equivalent and Volvo lifting hook 999 5460 or equivalent to raise the front of the engine a few millimeters.
  4. Remove or disconnect the following:
    • Right-hand engine mount
    • Right front wheel
  5. Turn the crankshaft until the markings on the crankshaft and camshaft pulley correspond. Turn the crankshaft a further 1/4 turn clockwise and then back again until the markings correspond. The markings are illustrated. Remove the upper timing cover.
  6. Slacken off the center screw for the belt tensioner slightly.
  7. Turn the tensioner clockwise to 10 o'clock.
  8. Remove or disconnect the following:
    • Air baffles
    • Lower belt cover
    • Timing belt


To install:
  1. Turn all the pulleys listening for bearing noise. Check to see that the contact surfaces are clean and smooth. If the tensioner pulley lever or idler is seized, replace it.
  2. If replacing with a new idler pulley, tighten to 18 ft. lbs. (24 Nm).
  3. If replacing tension pulley, screw into place using the center bolt by hand. Ensure that the tensioner fork is centered over the cylinder block rib. Ensure that the Allen hole on the eccentric is at "10 o'clock".
  4. Install the timing belt in the following order:
    1. Around the crankshaft sprocket
    2. Around the idler pulley
    3. Around the camshaft sprockets
    4. Around the water pump
    5. Onto the belt tensioner
  5. Carefully turn the crankshaft clockwise until the timing belt is tensioned. The belt must be tensioned between the intake camshaft pulley, the idler pulley and the crankshaft
  6. Hold the belt tensioner center screw secure. Turn the belt tensioner eccentric counter-clockwise until the tensioner indicator passes the marked position.
  7. Then turn the eccentric back so that the indicator reaches the marked position in the center of the window and tighten the center bolt to 15 ft. lbs. (20 Nm).
  8. Press the belt to check that the indicator on the tensioner moves easily.
  9. Install or connect the following:
    • Lower belt guard
    • Air baffles
    • Upper timing cover
  10. Turn the crankshaft two turns. Check that the markings on the crankshaft and camshaft pulley correspond.
NOTE Check that the indicator on the belt tensioner is within the marked area.

  1. Install or connect the following:
    • Lower timing cover
    • Front timing cover and tighten to 9 ft. lbs. (12 Nm)
    • Accessory drive belt
    • Engine mount and tighten to 49 ft. lbs. (67 Nm)
    • Servo reservoir. Tighten bolts to 37 ft. lbs. (50 Nm).
    • Front wheel
    • Right hand engine cover
    • Cover over the right headlamp
    • Negative battery cable

May 04, 2010 | 2000 Volvo V40

1 Answer

Where can i find a diagram of the 1996 mercury villager water pump placement


I can sell you a shop manual ans wiring book for $25 plus postage or you can go to our website.

http://groups.yahoo.com/group/villagerquest/

  1. Drain the cooling system. Refer to Section 03-03 for the procedure.
  1. Disconnect the battery ground cable (14301).
  1. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedures.
  1. Raise and support the vehicle.
  1. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts.




  1. Remove the water pump pulley from the water pump (8501).
  1. Remove the crankshaft pulley (6312). Refer to the procedure in this section.
  1. Remove the five lower engine front cover bolts and the lower engine front cover (6019).




  1. NOTE: Make a note of the location of the one water pump stud/bolt for ease of installation.

    Remove the six water pump bolts.




  1. Remove the water pump.
Installation
  1. NOTE: Ensure the mating surfaces between the water pump and the cylinder block (6010) are cleaned of any sealant material.

    Install a continuous 2.0-3.0mm (0.079-0.118 inch) wide bead of Gasket Maker E2AZ-19562-B or equivalent meeting Ford specification WSK-M2G348-A5, on the water pump and position the water pump on the cylinder block.




  1. NOTE: Refer to the note made during removal for the location of the stud/bolt.

    Install the six water pump bolts. Tighten the water pump bolts to 16-21 Nm (12-15 lb-ft).
  1. Position the water pump pulley on the water pump and install the four water pump pulley bolts.
  1. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley, and tighten the four water pump pulley bolts to 16-21 Nm (12-15 lb-ft).
  1. Install the lower engine front cover and the five lower engine front cover bolts. Tighten the five lower engine front cover bolts to 3-5 Nm (27-44 lb-in).
  1. Install the crankshaft pulley. Refer to the procedure in this section.
  1. Lower the vehicle.
  1. Install and adjust the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the installation and adjustment procedures.
  1. Connect the battery ground cable.
  1. Fill the cooling system. Refer to Section 03-03 for the procedure.
  1. Start the engine (6007) and check for leaks.

Apr 26, 2010 | 1996 Mercury Villager

1 Answer

Oil leaking out the front of the lower fan belt


If the lower fan belt pulley you are referring to is the vibration damper or harmonic balancer, then that is the pulley that is attached to the engine crankshaft, and that pulley is what turns all the other pulleys on the engine. There is a seal on the shaft behind the pulley -the front main seal. This is what may be leaking oil, and if that is the case , the seal needs to be replaced.
If it is the front main seal, and you are going to tackle the repair, you need to get a Repair Manual for your vehicle and follow the directions for the fix.

Jul 09, 2009 | 1990 Mazda B-Series

2 Answers

REMOVAL OF WATER PUMP ON 95 MERCURY VILLAGER


go here too http://autos.groups.yahoo.com/group/villagerquest/ Section 03-01: Engine 1996 Villager Workshop Manual IN-VEHICLE SERVICE -------------------------------------------------------------------------------- Water Pump Removal Water Pump Removal Drain the cooling system. Refer to Section 03-03 for the procedure. Disconnect the battery ground cable (14301). Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedures. Raise and support the vehicle. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts. Remove the water pump pulley from the water pump (8501). Remove the crankshaft pulley (6312). Refer to the procedure in this section. Remove the five lower engine front cover bolts and the lower engine front cover (6019). NOTE: Make a note of the location of the one water pump stud/bolt for ease of installation. Remove the six water pump bolts. Remove the water pump. Installation NOTE: Ensure the mating surfaces between the water pump and the cylinder block (6010) are cleaned of any sealant material. Install a continuous 2.0-3.0mm (0.079-0.118 inch) wide bead of Gasket Maker E2AZ-19562-B or equivalent meeting Ford specification WSK-M2G348-A5, on the water pump and position the water pump on the cylinder block. NOTE: Refer to the note made during removal for the location of the stud/bolt. Install the six water pump bolts. Tighten the water pump bolts to 16-21 Nm (12-15 lb-ft). Position the water pump pulley on the water pump and install the four water pump pulley bolts. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley, and tighten the four water pump pulley bolts to 16-21 Nm (12-15 lb-ft). Install the lower engine front cover and the five lower engine front cover bolts. Tighten the five lower engine front cover bolts to 3-5 Nm (27-44 lb-in). Install the crankshaft pulley. Refer to the procedure in this section. Lower the vehicle. Install and adjust the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the installation and adjustment procedures. Connect the battery ground cable. Fill the cooling system. Refer to Section 03-03 for the procedure. Start the engine (6007) and check for leaks.

Jun 06, 2009 | 1995 Mercury Villager

1 Answer

Need the belt diagram for the water pump belt for a 95 Auroa


42161874BELT, REPLACE
  1. Release belt tension and remove belt from power steering and alternator pulleys. Twist belt to get between tensioner and front cover and between power steering pulley and engine mount bracket.
  2. Raise and support vehicle.
  3. Turn wheel to the extreme right and remove right side splash shield.
  4. Remove belt from crankshaft and A/C compressor pulleys. Twist belt to get between idler pulley and engine mount bracket.
  5. Lower vehicle.
  6. Twisting new belt to get past the front cover, install belt around power steering pump pulley, Fig. 15. Allow belt to hang free.
  7. Twist belt to get between tensioner and front cover, wrap belt around alternator.
  8. Remove belt from power steering pulley and set aside.
  9. Raise and support vehicle, then twist belt to get between tensioner and front cover, wrap belt around crankshaft and A/C compressor pulleys.
  10. Install right side splash shield and lower vehicle.
  11. Position belt around power steering pulley and release tensioner.

Nov 23, 2008 | 1995 Oldsmobile Aurora

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...