Question about 1994 Toyota Camry

2 Answers

Changing transmission in 1994 toyota camry xle

Xle v6 need instructions on how to take out transmission and put another one in

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

What type tranny do you have in your car, auto or manual. If you let me know the type I will help you how to do it from start till the end

Posted on May 10, 2014

  • Sarah Smith
    Sarah Smith Dec 30, 2014

    I have a automatic trans

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 3,961 Answers

Well with a V6 it is most likely an auto? See here

http://www.turboninjas.com/camry/ax2.pdf

If a manual after all see here

http://www.turboninjas.com/camry/mx.pdf

Posted on May 08, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 18 Answers

SOURCE: How do I change the 3 spark plugs on the back of engine

The upper intake has to be taken off to get to them. Yes it is a pain in the but, not too hard to do, just bothersome to do this to be able to change plugs. Make sure to be careful when loosening the intake as the head is aluminum and you can damage it if you take a gung-ho approach. You will need to replace the gasket but it is only around 12 -15 $ .

Posted on May 08, 2009

motorhead427
  • 24 Answers

SOURCE: how to change a rear wheel bearing on a 1994 toyota camry

The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

Posted on May 30, 2009

techbuster
  • 5081 Answers

SOURCE: 2002 toyota sienna change transmission fluid and

The drain plug is on the bottom of the transmission. Its torqued to 49 nM.
1. Remove tranny oil pan drain plug
2. Drain old fluid (roughly 2-4 quarts)
3. Reinstall drain plug.
4. Measure amount drained in a 99 cent orange juice pitcher from Walmart
5. Pour back the same amount drained using Toyota Type T-IV fluid (available in 1 quart bottles from a Toyota dealer.
6. Start engine and shift slowly through all the gears ending in Park.
7. Check fluid level on the dipstick. Add fluid, if necessary, to bring the level to a point inbetween the COLD and HOT marks on the dipstick.
8. Go for a 20 minute drive and recheck fluid level. Add fluid, if necessary, to bring the level up to,
but not beyond, the upper half of the HOT range on the dipstick.

As in 1973, NO FLUSHING is needed and NO FILTER REPLACEMENT is needed, NO PAN REMOVAL is needed. As, as in 1973 todays Toyotas have a metal mesh filter screen that doesn't ever get clogged except in rare cases of transmission operational abuse, including failure to ever change the fluid for 150,000 miles or more.

Posted on Nov 21, 2009

  • 3 Answers

SOURCE: HOW TO CHANGE BRAKE LIGHT BULB ON A 2005 TOYOTA

Take cover off back at the trunk and it will pop out push in light twist off and put new one in

Posted on Jan 06, 2010

  • 184 Answers

SOURCE: 1992 Toyota Camry won't crank

Check the ground cable going from the battery to
alternator, then to chassis. Make sure there is no
rust at the chassis ground wire terminal, and that it
is very tight. The fusible link will be off the alternator
red power cable,usually, but not 100% on that car.
Good luck.

Posted on Mar 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 Toyota Camry XLE V6 Fuel Pump Switch Location


The pump gets power from the circuit opening relay and the EFI main relay, which are supplied through the EFI fuse. p219 here

http://www.turboninjas.com/camry/eg2.pdf

and

http://www.turboninjas.com/camry/be.pdf

May 04, 2012 | 1994 Toyota Camry

1 Answer

1994 camry xle v6 smoke coming from dash when we turn the car off and noise coming from speakers and radio is off


Hi there,

My first move would be to check any aftermarket equipment for wiring faults.

Beyond that I would need you to comment back with more details as to whats happening.

Best regards
Mike

Mar 22, 2010 | 1994 Toyota Camry

3 Answers

Downshift problem in 2005 Camry XLE V6


Check your motor and transmission mounts.

Mar 05, 2010 | 1999 Toyota Camry Solara

1 Answer

94 Camry V6 XLE; 278kmiles; Reverse only; Sudden poblem


most likly the trans is just plain worn out you could have it rebuilt or replace it with a used one

Jun 03, 2009 | 1994 Toyota Camry

2 Answers

How do I change the 3 spark plugs on the back of engine


The upper intake has to be taken off to get to them. Yes it is a pain in the but, not too hard to do, just bothersome to do this to be able to change plugs. Make sure to be careful when loosening the intake as the head is aluminum and you can damage it if you take a gung-ho approach. You will need to replace the gasket but it is only around 12 -15 $ .

May 07, 2009 | 1992 Toyota Camry V6

1 Answer

Need to install power mirror - driver side 1994 toyota camry xle


take the screws out, pop off the panel, disconnect the wire connectors, make sure you dont lose the screws.

to put the panel back on: reconnect the wire connectors, put panel back on track, pop panel on (hit the corners), put the screws in and tighten them.

Nov 18, 2008 | 1994 Toyota Camry

Not finding what you are looking for?
1994 Toyota Camry Logo

Related Topics:

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...