Question about 1992 Chevrolet C1500

1 Answer

1992 Chev 1/2 ton 4x4 front left wheel bearing replacement how to and tips

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

Instead of explaining step by step. I will guide you to a full free online repair manual for your entire vehicle. This will give you step by step directions, with illistrations.

Go to www.autozone.com, than register for free.
Than go to the site, select vehicle repair guides, pick your vehicle, and THERE YOU GO!
You now have the guide that will explain how to remove the cotter pin, cap, bearing, and everything else.

Posted on Jun 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace rear axel bearing on 1999 chev suburban k1500 4x4


Lots of Youtube videos to help you with that.

Jan 30, 2015 | Cars & Trucks

1 Answer

1992 4x4 front wheel bearing adjustment


To follow the "specs" you need a special socket with four pins (google should find a picture) to torque the bearing nut. These are crush bearings and are designed to be tighter than the older style bearings.
The bearing nut is under the locking hub, behind the locking washer that is fastened down with four screws.

Mar 27, 2012 | Suzuki Vitara Cars & Trucks

1 Answer

What are the front wheel bearing torque specs? For 2000 Chev silverado 2500 4x4,motor 6.0.


Those vehicles should have a hub assembly which incorporates a bearing and hub in one unit. To my knowledge the bearing is not serviceable. The hub assembly is bolted to the steering knuckle, so there actually is no wheel bearing torque. The tire/wheel assembly bolts directly to the wheel flange on the new hub assembly.

Dec 31, 2010 | Chevrolet Silverado 2500 Cars & Trucks

1 Answer

Replaced Hydro booster on a 97 chev 1 ton. Now has no pedal at all. I assume it needs to be bleed. What the proper way. Thanks


start at the furtherest bleeder away from your master cylinder,bleed untill no air from each one move on to next further.that should be right rear-left rear-right front-left front.just keep an eye on the fluid between wheels.hope the booster was your problem and this helps

Aug 25, 2010 | Chevrolet 3500 Cars & Trucks

1 Answer

1992 Dodge Pickup d150 1/2 ton need to know the torque for the front wheel bearings. Thank you


after packing your berrings tighten the nut untell the wheel stops turning , then back the nut off 1 flat ( the nut has 6 flat) wheel should now turn with minamal drag

May 20, 2010 | Dodge Ram Pickup 1500 Cars & Trucks

2 Answers

How do I replace the front wheel bearings on a


remove cv outer nut, tire brake caliper and lower ball joint use a bar to pry against lower a frame to seperate ball joint slip out cv axel then remove four nuts securing wheel bearing. I would have to check at home for exact instructions.

May 18, 2010 | 2005 Chevrolet Silverado

1 Answer

1996 Dodge 4x4 1 ton leaking pasenger front seal how to replace?


if u have u joints there should not any fluid near your bearing other than grease... if it is leaking anything other than that it is probably brake fluid... i would suggest checking your brake cylinder and brake line leading along side the passenger side

Apr 21, 2009 | 1996 Dodge Ram 3500 Club Cab

1 Answer

4x4 fuse on 1991 chev 1/2 ton keeps blowing..Why?


You might have a short in your wiring some where from the actuator back to where the wires go through the cab .could have been rubbing on something to cause this . just a thought

Jan 13, 2009 | 1991 Chevrolet C/K 2500

3 Answers

Hub assembly and wheel bearings problem


Plan on spending more than $75 on this repair I am quite shore that that wont evan cover the parts. It definitely has a wheel bearing in the case of this vehicle it can only be replaced as an assembly that includes the hub. The ABS wheel speed senser is often sold as part of the assembly or in some cases is sold separately. good chance it will need to be replaced. Get the job done as soon as possible this is a very unsafe condition Your wheel will fall off while driving eventually if not repaired

Jan 06, 2009 | 2000 Chevrolet Blazer

2 Answers

My 4x4 in my k1500 chev 1/2 ton makes a bad grinding noise in 4x4


chain can't slip, but if noise is definitely in t case, there is either an engagement problem or some serious internal damage!

Dec 27, 2008 | 1993 Chevrolet K1500

Not finding what you are looking for?
1992 Chevrolet C1500 Logo

Related Topics:

202 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...