Question about 2009 Toyota Highlander V6

1 Answer

P0135 code o2 sensor heater circuit malfunction (bank 1 sensor 1)

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 104 Answers

The heater element in the sensor has failed. Very high chance that replacing the O2 sensor will fix this issue.

Rare, but the engine computer may not be sending a signal to heat the sensor or a wire can be damaged. but this is very rare. Try replacing the sensor first. Its very simple.

this code is showing you the computer knows the circuit is not complete for some reason.

Posted on Jun 14, 2014

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
mcalkins3
  • 123 Answers

SOURCE: diagnostic code p0135

What engine is in this vehicle? I assume the avalon would be a 3.0L or similar V6 engine. Bank 1 sensor one indicates one of the primary O 2 sensor controlling a/f ratio. Sensor one bank one would be the sensor located in the Front manifold, closest to the engine. Hope this solves your issue. I would first check the conector at this sensor for corrison before buying a new sensor.

Posted on Sep 29, 2008

superjorge1
  • 8 Answers

SOURCE: have p0130 and p0133 codes 98 toyota tacoma

check the mass air flow sensor there maybe dirt on the filiment inside the sensor causing false readings. cleaning or replacing it may make the codes go away.

Posted on Nov 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi i have a 2002 ford ranger and it has teas codes P0446 P0135 P0141 P2195 P0403 P0171


P0446: EVAP System Vent Control Circuit http://www.autocodes.com/p0446_ford.html

P0135: O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 1
P0135 Ford O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 1

P0141: O2 Heater Circuit Bank 1 Sensor 2
P0141 Ford O2 Heater Circuit Bank 1 Sensor 2

P2195: Oxygen Sensor Signal Biased/Stuck Lean - Bank 1 Sensor 1
http://www.autocodes.com/p2195_ford.html

P0403:Exhaust Gas Recirculation Control Circuit http://www.autocodes.com/p0403_ford.html

P0171: Fuel Injection System Too Lean Bank 1 http://www.autocodes.com/p0171_ford.html

Nov 15, 2016 | 2002 Ford Ranger

2 Answers

Trouble code p0134, p0135 p0053 p0030


P0134 - O2 Sensor Circuit No Activity Detected Sensor 1 Bank 1
P0135 - O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 1
P0053 - O2 Heater Resistance Bank 1 Sensor 1
P0030 - O2 Heater Control Circuit Bank 1 Sensor 1
You need to replace the O2 Sensor Bank 1 Sensor 1
Carquest can help you get the correct part and help you locate it.

Apr 01, 2014 | 2006 GMC Envoy Xl

1 Answer

What is diagnostic procedures for DTC p0135 & p0141


Oxygen Sensor problems... P0135 (Bank 1, Sensor 1) and P0141 (Bank 1, Sensor 2)

P0135 - Oxygen O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 1)
This code refers to the front oxygen sensor on Bank 1. The heated circuit in the oxygen sensor decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it.

The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0135.

Symptoms: You will likely notice poor fuel economy the illumination of the MIL.

Causes: A code P0135 may mean that one or more of the following has happened:
O2 Heater element resistance is high
Internal short or open in the heater element
O2 heater circuit wiring high resistance
open or short to ground in the wiring harness

Possible Solutions:
Repair short or open or high resistance in wiring harness or harness connectors
Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)



P0141 - O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 2)
This code means that the heated circuit in the oxygen sensor on bank 1 decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it. The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0141.

Symptoms: You will likely notice poor fuel economy the illumination of the Check Engine Light.

Causes: A code P0141 may mean that one or more of the following has happened:
open or short to ground in the wiring harness
O2 heater circuit wiring high resistance
O2 heater element resistance is high
Internal short or open in the heater element

Note: Typically a failed catalytic converter does not cause this code. You're more likely to see a P0420 code for a failed converter.

Possible Solutions:
Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)
Repair short or open or high resistance in wiring harness or harness connectors


Hope this helps (remember to rate this answer)..

May 11, 2011 | 2000 Nissan Maxima

1 Answer

I'm thinking about buying a 2002 range rover. It has a service/check engine codes of 134,135,155. Is it likely to be more than oxygen sensor problems? Please reply , Mel


with those codes showing, it could be either bad O2 sensors or there is a problem with the wiring to those sensors. Also, the wrong sensors may be installed. I'm assuming codes P0134, P0135, P0155.

For others viewing this:

P0134 = O2 sensor circuit-no activity detected (bank 1 sensor 1)

P0135 = O2 sensor heater circuit malfunction (bank 1 sensor 1)

P0155 = O2 sensor heater circuit malfunction (bank 2 sensor 1)

Feb 11, 2011 | 2002 Land Rover Freelander

1 Answer

Engine light on--when do scan shows code P0135


P0135=O2 sensor heater circuit malfunction (bank 1, sensor 1)

O2 sensors have built in heaters to help them warm up faster. The O2 sensor in the No.1 bank of cylinders may have an inoperative heater or the wiring to the heater element is damaged. Changing that O2 sensor may correct your problem.

Feb 03, 2011 | 2006 Honda Element

2 Answers

Code error number p0135


P0134....O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 1)


P0135....O2 Sensor Heater Circuit (Bank 1 Sensor 1) heater in the O2 sensor has packed up first sensor before the cat

Nov 27, 2010 | Jeep Grand Cherokee Cars & Trucks

2 Answers

I have a gmc envoy & the trouble codes are p0107,p0130,p0135 & p0171 can you tell me what the problem can be.


P0107 Manifold Absolute Pressure/Barometric Pressure Circuit Low Input

P0130 02 Sensor Circuit Malfunction (Bank I Sensor 1)

P0135 02 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)

P0171 System too Lean (Bank 1)

Check your Manifold Absolute Pressure Sensor, and it might be a good time to install a new Upstream O2 Sensor.

It might also be beneficial to have your fuel pressure checked if the engine is really running Lean, but this may be caused by a faulty O2 sensor.

Jul 19, 2010 | GMC Envoy XL Cars & Trucks

1 Answer

P134, p0141, po300, po130 and po135. 2005 Sunfire.


Given that most of the trouble codes are for the O2 sensor, I think I would change it. The multiple misfires could be because of improper fuel/air mixture caused by a bad sensor. Disconnect the negative(-) battery terminal then change the sensor. Disconnecting the negative(-) should reset the computer and allow the fuel/air mixture to return to default allowing the engine to start.
P0130 - O2 Sensor Circuit Malfunction (Bank 1 Sensor 1)
P0134 - O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 1)
P0135 - O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
P0141 - O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
P0300 - Random/Multiple Cylinder Misfire Detected

Jun 16, 2010 | 2005 Pontiac Sunfire

1 Answer

More 99 cougar problems


there is a fuse for the o2 heaters if one of the sensors blew the fuse they will all be out

Feb 14, 2009 | 1999 Mercury Cougar

Not finding what you are looking for?
2009 Toyota Highlander V6 Logo

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...