Question about 2002 Chrysler 300M

1 Answer

Hood release inside car isn't working

The interior hood release isnt working is there a way to relase the hood manually?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Yes actually, you might need to lay on your back with a pair of pliers though, when you pull on the hood-release handle under the dashboard, you will see a wire cable behind the plastic handle, grip that wire with the pliers and pull till you hear the hood pop, then adjust the cable from under the hood to remain shorter.(it's stretched a bit over time is all)

Posted on May 07, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 BMW 528i interior hood release cable missing how do I open hood


The hood catch is so well inclosed, you won't get the hood open manually. No tricks here. There has to be a release inside the car. If the handle is just missing, and you can get to the release cable, just pull it with a pair of pliers.

Sep 25, 2014 | BMW 528i Cars & Trucks

1 Answer

My 94 geo prizm hood release works but then the hood doesn't lock when I drop it back down


Either the latch is defective or the relase cable is not fuklly releasing the latch to relock.

Mar 20, 2014 | Geo Prizm Cars & Trucks

1 Answer

2008 Mitsubishi release cable for Hood not working. When pulling on release inside car, the hood does not pop open to reach under and release the safety latch


I have a similar problem on my 2006 VW Passat.

I'm able to open the hood two ways:
1) ask someone to hold onto the lever inside the car while you try to lift the hood to the point where you can use the unlatch button and open the hood fully.


2) Pull the lever completely open in the car and try to find a thick screwdriver or some thick paper folded up to wedge next to the lever to hold it open while you get out and try to lift the hood to the point where you can use the unlatch button and open the hood completely.


Other than this finding a service manual or tutorial online about how to pull out whatever trim or interior covers you would need to replace the cable fully. There should be a specific replacement guide for this item since I'm sure it happens to car's at least semi-regularly

Aug 31, 2013 | Mitsubishi Galant Cars & Trucks

1 Answer

Relase lock on hood 2003 sable


Happens all the time. The easiest way is to have someone pry it up for you while you pull the handle. Be gentle don't scratch the paint. Flat head screwdriver wrapped in a rag works best.

Feb 23, 2013 | Mercury Sable Cars & Trucks

2 Answers

Bentley Boot lid manual release


This is all the Bentley shows:

doorlockswitch1.gif
Location: Driver's side door trim in storage compartment.

Removing:

- Remove driver's side door trim:
Repair Manual, Body Interior, Repair Group 70 - Unplug connectors.


doorlockswitch2.gif
Carefully disengage catches -arrows-.
- Press switch for interior monitoring and towing protection -1- or trunk release switch -2- out of trim toward rear.

Installing

Installation is carried out in the reverse order.


doorlockswitch3.gif
Remove trunk lid lock.

Repair Manual, Body Exterior, Repair Group 55
- Use a flat screwdriver to pry plastic tab -3- off retaining pins -1-.
- Bend plastic tab fully to rear.
- Pull contact switch -2- first sideways and then up and out of trunk lid lock.

Installing

Install in reverse order, paying attention to the following:

Note:

Make sure that washers are correctly seated between plastic tab and trunk lid lock.

Sep 01, 2012 | Bentley Continental Flying Spur Cars &...

1 Answer

Hood on 2001 town car will not open ? any idea's on how to get it open when release will not do anything & what could be wrong with it pull's but does not relase ................


have someone press on the hood as you pull the release. You may have to shake the hood up and down to get the release to work. after you get the hood open, spray the latch with lube to free it up.

Sep 19, 2011 | Lincoln Town Car Cars & Trucks

1 Answer

The interior hood release isnt working is there a way to relase the hood manually from outside the truck on a 2010 toyota tundra


try this,have another person push down on the hood in the front of your truck,while they apply downward pressure,pull hood release out,keep the hood release pressure pulled out,tell the other person to let up on hood,then release the pressure you have on the hood release handle and hood should pop up.if this does'nt work,you have a broken hood release cable.that means you'll have to get on the ground under front of truck and reach up to the hood release cable with pliers and pull the cable release manually.good luck hope this helps and thank you for choosing fixya.com

Jan 10, 2011 | Toyota Tundra Cars & Trucks

2 Answers

How do I open the hood of a Mitsubishi L300 ?


  1. Locate the interior hood-release lever under the dashboard on the driver's side of the interior of the car.

  2. 2

    Lift up and toward you on the hood release lever. The lever is connected to a cable that releases the hood. The hood will pop up about 1/2 inch when you pull the lever.

  3. 3

    Move to the front of the car and locate the exterior hood-release lever under the front of the hood. It is located near the middle of the vehicle, just beyond where the front edge of the hood meets the body. Lift up on the inner lever.

  4. 4

    Lift up on the edge of the hood while holding the inner lever in place. When the hood is up, find the hood prop and raise it, setting its tip in the hood-prop mount on the hood, to hold the hood up while you work in the engine bay.



Read more: How to Open the Hood on a Mitsubishi Endeavor ' eHow.com http://www.ehow.com/how_6301122_open-hood-mitsubishi-endeavor.html#ixzz16Ou5FhQF

Nov 26, 2010 | Mitsubishi Lancer Cars & Trucks

1 Answer

Back hatch is jammed on one side. How do I fix it.


u will need to remove the interior trim panel and manually relase the latch, i get this question allot there is no other way, the panel is really hard to get off inside the van, so if u can afford a dealer do so.

Jan 18, 2010 | 1995 GMC Safari

1 Answer

My hood relase button inside van will not open the hood, i need to open it as my van will not start at all, its battery tried to crank over but just wont seem to turn all the way over to start. But yeah...


it has tension?? with assistant to pull cable you push down on bonnet and with any luck it will pop up,then oil the mechanism with some engine oil and not that silly wonder spray stuff thats all fish oil

Dec 17, 2009 | 2001 Ford Windstar

Not finding what you are looking for?
2002 Chrysler 300M Logo

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...