Question about 2006 Dodge Stratus

Open Question

Replace oil pan on dodge 2.4 litre engine - 2006 Dodge Stratus

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ams51pr
  • 21 Answers

SOURCE: replacing oil pan on 2003 dodge neon

To replace the oil pan jack and place car in towers. Remove the undercover shielding and watch out for the exhaust that will also have to be move. Drain the oil pan. The holding bolts will be removed with appropriated tools. Tap with wood block to lose it. Once removed check the oil pump for damage. To replace make sure to used a proper gasket and sealant. Install all parts back.

Posted on Jul 05, 2008

Ad
  • 160 Answers

SOURCE: RATTLING NOISE AT OIL PAN AREA ON 1998 DODGE RAM 1500 5.9 LITER

rod bearing , engine needs rebuilt

Posted on Nov 12, 2008

  • 73 Answers

SOURCE: Oil Pan Gasket

the oil pump is in the oil pan attached to the block. there for you have to raise the engine so you can see the oil pump and get the gasket under it to get it to slide into place. my suggestion is to raise the engine and replace the gasket

Posted on Feb 03, 2009

Keith100881
  • 74 Answers

SOURCE: oil pan rusted out, needs replacing

which eng. 3.9 5.2 5.9 v8 5.9l6

Posted on May 24, 2009

  • 31 Answers

SOURCE: I need to replace the oil pan on my 2002 Dodge

1.put car on a lift. 2.Drain oil. 3.make sure to have exact oil pan ready with seal in hand. 4.unscrew the bolts in a x fashon. 1-6 3-4 2-5 remove oil pan. 4.Clean all around where the oil pan used to be. 5.Attach new seal and oil pan. hand tighten all the bolts in a X fashon then tighten with a wrench or socket. 6.make sure oil drain plug is on good. 7. put new oil in typically 5 quarts. 8.put car on ground 9. All done.

Posted on Sep 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Transmission oil pan replacement


Measure all the fluid you drain and replace it with the same amount plus 1/4 quart.

Jul 05, 2016 | 2007 Dodge Nitro

1 Answer

HOW DO I REMOVE THE OIL PAN OFF A 2003 DODGE STRATUS 2.4L 4CYL


Oil pan removal
1. Disconnect negative cable from battery.

2. Raise vehicle on hoist.

3. Drain engine oil and remove oil filter.

4. Remove oil filter adaptor from engine block

5. Remove structural collar

6. Remove lateral bending brace.

7. Remove transaxle dust cover.

8. Remove oil pan bolts.

9. Remove oil pan.

Feb 09, 2015 | 2003 Dodge Stratus

1 Answer

Where is the oil pump located 1994 mazda b4000 4.0 litre


The oil pump is in the oil pan.
On 4.0 engines with vin code E you may have to remove the engine to be able to remove the oil pan.

Jan 29, 2013 | Cars & Trucks

1 Answer

I have a 96 dodge stratus that is a 2.4 litre and the oil pan is leaking oil. I need to replace it but the pan is under the engine mount bar that goes from the front to the back of the engine. Whats the...


if you have an engine cranem you can hold the engine, disconnect the engine and transmission mounts (disconnect the battery first) and raise the engine assembly up enough to clear the pan out of the way, just remember it has to be high enough to clear the oil pick up.......if not, engine out unfortunately

when the manufacturer creates a vehicle, they are not fussed too much about the serviceability of the engine itself, as it should last the warranty period.....oh, well, what do you do

Jun 11, 2010 | 1996 Dodge Stratus

1 Answer

Whats the best way to get to the oil pressure sending unit on a 5.9 litre dodge ram


The oil pressure "sending unit" pump is located in the oil pan, in/at the bottom of the engine. It's not something I'd recommend trying if you've never attempted a lengthy or relatively difficult repair, without guidance. You don't indicate if you have 2wd of 4wd. However, in any event, you're going to have to remove the oil pan. It will most likely require you to loosen the motor mount(s) and jack/lift up the engine. Not necessarily the best way, but the easiest. I'd be concerned with engine wear also if the oil pump is bad. Which would require you to at least change the connecting rod and main bearings.

Mar 05, 2010 | 1999 Dodge Ram

1 Answer

I need to replace the oil pan on my 2002 Dodge Intrepid with a 3.5 Liter engine. What are the steps. Especially with the metal ubber pan gasket.


1.put car on a lift. 2.Drain oil. 3.make sure to have exact oil pan ready with seal in hand. 4.unscrew the bolts in a x fashon. 1-6 3-4 2-5 remove oil pan. 4.Clean all around where the oil pan used to be. 5.Attach new seal and oil pan. hand tighten all the bolts in a X fashon then tighten with a wrench or socket. 6.make sure oil drain plug is on good. 7. put new oil in typically 5 quarts. 8.put car on ground 9. All done.

Sep 02, 2009 | 2002 Dodge Intrepid

2 Answers

Dodge 2005 Grand Caravan water Pump replacement


JUST COMPLETED THIS JOB TODAY. MAKE SURE THE ENGINE HAS COOLED DOWN . IT TOOK APPROX 2 1/2 HRS. DISCONNECT THE NEGATIVE POST ON THE BATTERY. JACK UP PASSENGER SIDE FRONT AND SUPPORT ON JACK STANDS. REMOVE PASS. FROUNT TIRE. DRAIN RADIATOR INTO CONTAINER FOR PROPER DISPOSAL OR REUSE. USING FLOOR JACK PROVIDE SLIGHT TENSION ON OIL PAN WITH A SHORT 2 X 4 WOOD PIECE TO PROTECT OIL PAN. LOOSEN 3 ENGINE MOUNT BOLTS ON PASS. SIDE OF ENGINE COMPARTMENT. ALLOW APPROX 1" BETWEEN SHOULDER OF BOLTS AND MOUNT. LOWER ENGINE UNTILL BOLTS ARE SET ONTO MOUNT. REMOVE ENGINE SPLASH SHIELD INSIDE WHEEL WELL OF REMOVED TIRE. LOCATE WATER PUMP AND LOOSEN 3 PULLEY MOUNTING BOLTS (THIS IS WHILE BELT IS ON PULLEY) REMOVE SURPENTINE BELT AND CONTINUE TO FULLY REMOVE THE PUMP PULLEY. IT WONT COME OUT AS THE PUMP & PULLEY HAVE TO COME OUT TOGEATHER. REMOVE 5 WATER PUMP BOLTS AND CAREFULLY WORK WATER PUMP OUT BETWEEN THE ENGINE AND VEHICLE FRAME. CLEAN ALL MATING/GASKET SURFACES AND BOLTS. USING A SMALL AMOUNT OF TACKY SEALENT TO INSURE THE NEW WATER PUMP SEAL STAYS IN PLACE, THE INSTALL IS PRITTY MUCH THE REVERSAL OF REMOVAL.

GOOD LUCK, REMEMBER TO TIGHTEN ALL BOLTS TO MFR SPECS AND BLEED THE AIR OUT OF THE COOLANT AS REQUIRED.

Mar 30, 2009 | 2005 Ford F-150

1 Answer

Where is the oil pan located on me 1997 lincoln continental?


The simple answer is, bolted to the bottom of the engine. Ford and Lincoln vehicle generally have the cross member right under the engine, so the oil pan is obscured by it. Many oil pans on rear wheel drive Ford products have 2 oil sumps or wells, 1 near the front just behind the belt pulleys, and the other just behind the cross member, this one also has the oil drain plug for oil changes. Not sure why you are looking for the oil pan, so I hope this helps.

Feb 18, 2009 | 1997 Lincoln Continental

1 Answer

Oil Pan Gasket


the oil pump is in the oil pan attached to the block. there for you have to raise the engine so you can see the oil pump and get the gasket under it to get it to slide into place. my suggestion is to raise the engine and replace the gasket

Feb 02, 2009 | 2000 Dodge Ram 1500 Truck

Not finding what you are looking for?
2006 Dodge Stratus Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...