Question about Cars & Trucks

1 Answer

1988 Toyota corolla Ae82 5spd hatch what's the factory set point for the carby air/fuel mixture screw?. Iv had to replace the carby due to crack but the new used one is not set right and I can't seem to get a good tune.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Cars & Trucks Expert
  • 360 Answers

For the Asin 2bbl try from closed position (close gently) open approx.
1-1/2 to 1-3/4 as a starting point. Then with a tachometer hooked up slowly and carefully adjust in either direction to obtain highest RPM.

Posted on May 11, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
short shadey
  • 421 Answers

SOURCE: replacing starter on 1988 toyota corolla

should be on the back of the engine block going into the transmission somewhere you may need to get under the car to access it good luck please rate -jeff

Posted on Sep 05, 2008

motor1258
  • 6674 Answers

SOURCE: I don't know where the air/fuel mixture screw is on my carb

There should be one screw (I'm assuming it's the Carter YF carburetor 1 barrel) that's by itself away from linkages etc, more to center at base of carb where it meets manifold, that is angled approx 45 degrees going in to base. That should be your mixture screw. What symptoms are you experiencing anyway?

Posted on Apr 04, 2009

wesleygolden
  • 59 Answers

SOURCE: EF FORD FALCON NO FUEL GETTING TO CARBI

I think the word carburetor and ford falcon was mentioned which used a mechanical fuel supplied system. check for a cracked fuel supply line from the fuel tank to the steel body supply line.

Posted on May 10, 2009

snk_trd
  • 11 Answers

SOURCE: 2001 TOYOTA COROLLA NO POWER

This problem does not seem to be the fuel pump. it appears to be an electrical problem in particular your ignition. Also check the MAF (Mass Air Flow) sensor. if the computer cannot read how much air is coming in it will try to shut down.

Posted on Aug 03, 2009

  • 1 Answer

SOURCE: 1992 Toyota Townace, 3y engine.

let me now,i have toyota tunes1985,with2c,but i want to convert into petrol,which engine is suitable for my car?

Posted on Feb 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the factory setting for the fuel mixture screw on a toyota 1.8 litre 2Y engine


most fuel mixture screws are set initially by turning it all the way in and then backing out 21/2 turns. This should allow start and idle and final adjustment can be done to fine tune it. Check that the idle solenoid is working as it will shut off the idle circuit if it is not

Nov 01, 2014 | Cars & Trucks

1 Answer

My toyota corolla 1.6 16v carb dont want to idle


Check for missing/ broken vacuum hose. Remove vacuum hose for brake booster and plug That checks for air leaks in booster. Check for power to the idle solenoid unit .If that is not working the idle circuit of the carby is shut down. Adjust idle mixture screw as well.

Apr 21, 2013 | 1993 Toyota Corolla

1 Answer

What do i need to do a tune up


If you have a carby start with plugs, ht cables (good quality) timing light if you can get a test unit that has a exhaust gas reader that will help with tuning the carby. fuel filter/ air filter. check tyre pressures( flat tyres use fuel) and hand brake isn't staying on. Check front wheel bearings for correct adjustment. If you are doing a tune up ,all things affect fuel usage

Jan 19, 2013 | 1988 Toyota Corolla 4 Door

1 Answer

Hi from Costa Rica,i am owner 1988 Toyota corolla fx gts,i will like to know the Idle adjustment screw position (factory set)(not near T-VIS),i think this screw is idle mixture adjusting near the return...


adjust to about one and quater turns out from the in position but do not force it in if you know what i mean then start engine and adjust till it sounds right ,officially itsa supposed to be adjusted till it reads less that 2.0 CO2 but i doubt if you have vehicle inspection stations their as yet so when it sounds right is good enough

Aug 16, 2011 | Toyota Corolla Cars & Trucks

1 Answer

2006 Toyota Corolla Code P0171 What could be the problem?


po171 means the air fuel ratio is lean (not enough fuel) so you must check for anything that can do that a good example would be a vacuum leak that allows non metered air to enter the engine (more air same amount of fuel = lean mixture) or a clogged injector (same amount of air less fuel = lean mixture as well)

Jan 06, 2010 | 2003 Toyota Corolla

1 Answer

How to adjust fuel mixture 2 barrel carburater for


In the late 70's they mandated that the adjustment screws be capped over. If they haven't been exposed, there will be two plugs covering them on the baseplate. Air adjustment screws are always somewhere on the base of all carbs with the only exception being on Holley 4bbl carbs used on performance engines (definitely not yours)

Nov 18, 2009 | 1983 Toyota Corolla Tercel

1 Answer

I want to turn carby ae 92 down it is ideling to high as


on your carb you will find 2 screws 1 is a thritle stop screw the outher is the mixture screw the ajustment y need is the throttle screw hope this helps

Nov 15, 2009 | 1989 Toyota Corolla 2 Door

2 Answers

My 2001 toyota corolla stalls out when cold


It is registering engine too lean due to either too much air entering the engine via an intake leak or by an inaccurate reading from the MAF.

Often on these cars, particularly if they have used Toyota brand air filters, the MAF collects fuzz over time from the air filter.
As this 'fuzz' collects on the MAF element, it acts as an insulator and skews the airflow reading for the ecm; it sees less air than is actually going through, so when it checks your mixture on the way out of the engine it realizes that there is more air than it thought was going in.

Pull your MAF out of the air hose (two philips screws) and clean it with non-chlorinated brake cleaner or "MAF cleaner" available at your local parts store. Look in there with a flashlight, you will see a little coiled wire covered in little bits of fuzz before you start.

Do NOT touch the element, just use the cleaner to blast it clean. Let it air dry completely before reinstalling.



Clear the code and call it a day!

Sep 15, 2009 | 2001 Toyota Corolla

1 Answer

1988 daihatsu charade carburetor


If we are talking the three cylinder CB23 engine the mixture screw is hard to get to and has an anti tamper shroud to stop prying fingers.

The Aisan carby is pretty reliable and problems with them on these engines is usually due to improper vacuum hose connections, or improperly adjusted idle, fast idle and deceleration screws.

A/F ratio is around the standard 14.7, but being a carby you will not get consistent mixtures because the jets sizes are fixed . On an EFI engine you can control the fuel flow, but not so with jets.

If you do decide to give your carby a birthday make sure you only buy the Daihatsu genuine, because the after market units have issues with quality. The minor rebuild kit part No 0421287704000 and the major overhaul kit with plunger, needles, gaskets, clips, etc is part No 0421187729000.

If it was me I'd be concentrating on the hoses, the PCV valve, contact points in the dizzy and better spark plugs first. If you want much better idling and a bit better pull get an electronic dizzy and coil from a G200 series Charade.


Sep 07, 2008 | 1988 Daihatsu Charade

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...