Question about 2005 Ford Bantam 1.3i

Open Question

What is the timing chain marks on a Ford Bantam 1.3i?

My engine overheated. I had it overhauled and now need to set the timing chain so I need the markings to align it

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 33 Answers

SOURCE: 1997 ford explorer 4.0 sohc how to set timing

There are no timing marks. Timing is done using special tools to hold the crank at top center and a tool to hold each camshaft in position. the cam sprockets are not pinned to the cams. there are also dummy tensioners installed to take up the slack till the tightening is done. Also there are chains at the back of the motor that can only be timed with the motor out of vehical.

Posted on Feb 21, 2009

  • 1 Answer

SOURCE: how do you set the timing marks on 97 ford probe?

what marks are used when setting timing on 1997 ford probe

Posted on Apr 24, 2009

  • 701 Answers

SOURCE: where can i find the timing marks on 1998 ford escort zx2 ?

Hello pamgolmon: My name is Roger and i will answer your question. The 2-0 dual cam engine is a interference engine. This means if the engine jumps time at the timing belt. It will bend the valves. As for the timing marks on the camshafts. Their are no marks to be located. To set the timing marks on this engine requires special tools. This makes it expensive for not only the do it yourself mechanic but also the repair shops also. If the valves were bent you must pull the head for the repairs also.
I know this is not the answer you were hoping for but it is the only answer to give. Please rate the quality of the answer as this way we know your answer was correct. Please just ask if you need further help. Thank You for using Fix Ya. Roger

Posted on Sep 09, 2009

kennyz195
  • 61 Answers

SOURCE: 1999 Ford Expedition 5.4L Timing chain setup

.

  1. Remove the engine front cover. For additional information, refer to Engine Front Cover in this section.
  1. Remove the crankshaft sensor ring from the crankshaft.
    a0044041.gif
  1. Rotate the crankshaft until the timing mark on the RH camshaft sprocket is approximately at the 11 o'clock position and the timing mark on the LH camshaft sprocket is approximately at the 12 o'clock position.
    a0049532.gif
  1. Using the special tool, position the crankshaft as shown.
    a0041102.gif
  1. Install the special tool.
    aa5423a.gif
  1. NOTE: LH shown; RH similar.
    Remove the two bolts, the timing chain tensioner and tensioner arm.
    aa5952a.gif
  1. Remove the LH and RH timing chains and the crankshaft sprockets.
    • Remove the special tool from the crankshaft.
    • Remove the timing chains from the camshaft sprockets.
    • Remove the right and left timing chains and the crankshaft sprocket from the crankshaft.
    a0029151.gif
  1. ani_caut.gif CAUTION: The bolts are different lengths and must be returned to their original location.
    NOTE: LH shown; RH similar.
    Remove the bolts and the timing chain guides.
    a0044040.gif
Installation
  1. ani_caut.gif CAUTION: Timing chain procedures must be followed exactly or damage to valves and pistons will result.
    ani_caut.gif CAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly.
    Compress the tensioner plunger, using an edge of a vise.
    da0605a.gif
  1. Using a small screwdriver or pick, push back and hold the ratchet mechanism.
    da0606a.gif
  1. While holding the ratchet mechanism, push the ratchet arm back into the tensioner housing.
    da0607a.gif
  1. Install a paper clip into the hole in the tensioner housing to hold the ratchet assembly and plunger in during installation.
    a26917a.gif
  1. Remove the tensioner from the vise.
  1. NOTE: There are 61 links in the timing chain.
    If the copper links are not visible, mark two links on one end and one link on the other end, and use as timing marks.
    a0038720.gif
  1. Install the timing chain guides.
    a0044063.gif
  1. Using the special tool, verify correct crankshaft position.
    • Remove the special tool.
    a0041102.gif
  1. NOTE: Crankshaft sprockets are identical. They can only be installed one way. Refer to the following illustration for correct crankshaft sprocket installation.
    If removed, install LH and RH crankshaft sprockets.
    a14824b.gif
  1. Install the LH timing chain onto the crankshaft sprocket, aligning the one copper (marked) link on the timing chain with the slot on the crankshaft sprocket.
    a0041197.gif
  1. Position the LH timing chain on the camshaft sprocket with the two copper (marked) chain links and the camshaft sprocket timing mark aligned.
    a0049191.gif
  1. Position the RH (outer) timing chain on the crankshaft sprocket, aligning the copper (marked) link with the timing mark on the sprocket.
    a0041196.gif
  1. Position the RH timing chain on the camshaft sprocket. Make sure the two copper (marked) links align with the camshaft sprocket timing mark.
    a0041104.gif
  1. NOTE: LH shown; RH similar.
    Position the tensioner arms and tensioners, and install the bolts.
    aa5952a.gif
  1. Remove the tensioner retaining clip.
    a26273a.gif
  1. As a post-check, verify correct alignment of all timing marks.
    a0041106.gif
  1. Remove the special tool.
    aa5423a.gif
  1. Position the crankshaft sensor ring on the crankshaft.
    a0044041.gif
  1. Install the engine front cover. For additional information, refer to Engine Front Cover in this section.


2010&c18=modelyear&c20=n310677&c35=wsm%2ctiming%20drive%20components%2csxj%2c303-01b%2cin-vehicle%20repair&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=lan&hp=n&[aqe]

Posted on Apr 07, 2010

BCAS1298
  • 3092 Answers

SOURCE: setting timing belt 2.0 split port focus engine

Hope this helps.

39fe2de.gif

Posted on Jul 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHAT IS SYMPTOMS OF ILL OPERATING DISTRIBUTOR.WHAT IS THE CORRECT SPARK PLUGS FOR 2002 FORD BANTAM 1.6I .SHOULD I USE COPPER WIRE OR CARBON PLUG LEADS.


using a timing light, watch the light on the timing mark and if it is all over the place and not steady on the mark then that indicates a worn shaft and bushes in the distributor
use carbon resistance plug leads that have thick insulation( (not el-cheapo leads ) modern plugs are designed to run carbon leads
run the fault codes as the problem may be in the air /fuel control sensors and not the distributor or crank. cam position sensors

May 07, 2017 | Ford Cars & Trucks

1 Answer

My engine has a noise and oil sign is displayed and it does not go away although there is enough oil what it could be?


Bad oil pump? Bad bearings? Bad sender unit, but with bad noise probably the engine needs overhaul or replacement.

Jul 14, 2016 | 2007 Ford Bantam 1.3i

1 Answer

I have noise rocam when is run what wrong with my car


  1. Timing Chain
  2. Timing Chain Guides
  3. Timing Chain Tensioner
  4. Timing Chain Camshaft Sprocket, Crank Shaft Sprocket
Alert Engine Parts sells the above kit for approx R680

Also change the oil pump when changing timing chain kit and sump gasket seal.

Oct 02, 2015 | 2005 Ford Bantam 1.3i

1 Answer

How do I find timing marks on the harmonic balancer on 3litre 2006 ford fanger


Timing marks are increasingly being deleted from crank pulleys and harmonic dampers as they serve little purpose in this era of electronic engine management.
Timing belt and chain alignment marks are provided where they need to be for routine chain or belt replacements and subsequent overhaul work but even these are being superseded now engines are being jigged into alignment and assembled by robots. Workshops are increasingly expected to invest in special service tools for engine alignment.

If you can't find timing marks, the reason could be they simply aren't there.

Feb 28, 2015 | Ford Cars & Trucks

1 Answer

How do I replace a timing belt on a Bantam 1.6i XLT


if it rocam engine it does not have a belt it runs on a chain

Aug 20, 2014 | 2008 Ford Bantam 1.6i

1 Answer

Timing Settings


I need the tdc diagram and/ or setting for the ford bantam 1,3i 2006 model

Sep 09, 2013 | 2006 Ford Bantam 1.6i

2 Answers

Guys I've got a problem with a ford bantam 1.6i 2003 model rocam engine, its overheating even though the cylinder head was skim but it still overheating. please assist!


Check what head gasket was used . I suspect that an after market gasket was used. If that is the case there will be holes in the block and head thet have no matching holes in the gasket thereby causing the problem

Jan 07, 2013 | 2006 Ford Bantam 1.6i

Not finding what you are looking for?
2005 Ford Bantam 1.3i Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...