Question about Hyundai Motor 2004 Sonata

1 Answer

How do you replace rear brake on 2004 hyundai sonata 4 cyl

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 396 Answers

Assuming you have disk brakes. Remove the wheel, remove the brake capalier, remove the brake shoes, check the wheel cylinder ifits scarred remove and have researfaced. You will need a piece of wood, 6 inch c clamp, antiseizing compound and high temp grease. You must force the for a lack of a better word, force the pressure items back into the capalier with the c clamp. Place the shoes back on. You may want to remove some brake fluid out of the brake resivor to keep it from overflowing, Then add new fluid after replacing the pads.

Posted on Jun 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2012 hyundai sonata accelerates on its own


Just keep foot close to brake peddle. Hahaha. Jk. Spray some wd-40 on your throttle body and throttle cable. If not that then take of throttle body and clean butterfly.

Mar 24, 2016 | 2012 Hyundai Sonata Hybrid Base Sedan 2.4L...

1 Answer

Brake lights staying on 2004 sonata


Could be a stuck brake light switch near the brake pedal.

Jul 01, 2012 | Hyundai Motor 2004 Sonata

1 Answer

When my lights are on my brake light stays on in back on a sonata 2004


sir, your car's brake pedal switch get short which commands the rear lights..

Apr 28, 2011 | Hyundai Motor 2004 Sonata

1 Answer

Replacing timing belt


According to THIS ebay listing there are (kinda) 2: 1 is the T-belt; the other is a Balance Shaft Belt. Ask the shop what the belts are for (don't offer the info) and see what they say.

good luck,
Td

Apr 08, 2010 | Hyundai Motor 2004 Sonata

1 Answer

I have a sonata 2007 . which oil you offer to me?


2007 HYUNDAI SONATA 2.4L 4-cyl Engine Code [C]

All TEMPS......5W-20 preferred
Above -18C......10W-30 optional
Engine, with filter..........4 liters

2007 HYUNDAI SONATA 3.3L 6-cyl Engine Code [F]

All TEMPS......5W-20 preferred
Above -18C......10W-30 optional
Engine, with filter..........5.2 liters

Nov 29, 2009 | 2007 Hyundai Sonata Limited Sedan

1 Answer

2004 Hyundai Sonata 6 cyl


Depends on how MECHANICALLY INCLINED you are. Have you done any repair work on vehicle engines before? It's not that difficult to do if you know how to turn a wrench/ratchet and THINK about what you are doing and what you are dealing with... .attention to details. Ya think? On the 04 2.7 lit V6 Sonata, there are two nuts and 5 bolts (two long and three short) which hold the plenum to the RISER manifold. There are an additional 3 to 4 bolts at the rear (firewall side) which support the plenum (they're all 12mm bolts). You'll need to remove the intake air hose to lift the plenum out of the way to access the 3 plugs on the RH side (rear) of the engine. You'll want to replace the plenum gasket when you do this. When you reinstall the plenum, the tightening torque is 11-14 lb.ft. Do not tighten the REAR support bolts until after you torque the surge tank bolts to the intake (riser) manifold.
ab1cefd.jpg

Jun 13, 2009 | Hyundai Motor 2004 Sonata

1 Answer

We are attempting to change the Crankshaft Angle Sensor and struggling with what all needs to be taken off of the engine to get to the bottom of the sensor. 2004 Hyundai Sonata.


crank shaft sensor don't normally go bad on hyundai.do you have a code for this?and what is the complaint?on the v-6 its behind the timing belt.next to the crankshaft gear.on the 4 cyl. its on the front of the block below exh. manifold. and easy to remove.

Apr 11, 2009 | Hyundai Motor 2004 Sonata

Not finding what you are looking for?
Hyundai Motor 2004 Sonata Logo

Related Topics:

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...