Question about Chevrolet Malibu

Open Question

Where is the remote keyless entry module located on a 2005 Malibu Maxx

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: nissan murano 2005 sl keyless entry remote programing

Close all vehicle doors, LOCK doors using drivers side switch.

Insert key all the way into the ignition, (do not turn) remove key.

Repeat this step 5 times. (6 total)

Hazards should flash to indicate program mode.

Press any button on transmitter to be programmed, hazards should flash to indicate successfull program.

*For additional remotes, cycle drivers door lock UNLOCK, LOCK, press any button on remote, hazards should flash. Repeat step as necessary.

Ignition ON, (engine off) ignition OFF, UNLOCK using drivers side switch, test remotes.

Source

Posted on Aug 06, 2008

  • 2 Answers

SOURCE: Change battery/Reprogram remote

take the postive battery cable off then put it back on then turn your car over three times not start it but just turn it on off on off on off that should reset it. thats what they did to mine at the dealers and it cost me 120.00 bucks

Posted on Oct 29, 2008

  • 181 Answers

SOURCE: 2008 chevy malibu. how to program keyless entry remote

You must take it to the Chevy dealer.

Posted on Mar 09, 2010

Testimonial: "thank you"

  • 2 Answers

SOURCE: Need computer location in 2005 lincoln towncar

The code is on a paper label attached to a large plastic box containing several wiring harnesses behind the driver side door panel. Posts about it being on the trunk hinge arms, behind trunk panels, on computer module, behind the fuse box, and 'you have to go to the dealer' are incorrect for this series of Town Cars. After you remove the panel (you do not need to disconnect any wires), you will see the box up near the rear view mirror. An example code (3/4) (1/2) (5/6) (9/0) (1/2). If you press the keypad buttons in this order,left to right, the door locks will operate in the manner described in your opwner's manual.

Do a search on door panel removal to learn how to remove the panel. There are some good posts on this topic - some even have pictures.

Posted on Sep 06, 2010

  • 4 Answers

SOURCE: cant find push button keyless entry code

They haven't put the code on the trunk lid for at least 10 years. On the 500/Montego, it's printed on a sticker on the Smart Junction box. This box is behind the fusebox (under the dash on the driver's side, above your left foot), so the sticker is facing the engine. You can use an inspection mirror to see the sticker, but I was able to get my digital camera behind there and take several pictures, and I was able to see the code.

Posted on Sep 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the theft sysem located at on a 2005 Dodge Durango and how can I get to it


What's the problem your having NICK ? The theft system is incorporated in everything , engine computer , body control module ! There is a anti-theft control module , a transponder chip in the head of you ignition key !
The Sentry Key Immobilizer System (SKIS) is available as a factory-installed option on this vehicle. Vehicles equipped with this option can be readily identified by the illumination of the security indicator in the instrument cluster for about three seconds after the ignition switch is turned to the ON position as a SKIS bulb test.
The SKIS includes the following major components, which are described in further detail elsewhere in this service information:
  • Powertrain Control Module (1)- The Powertrain Control Module (PCM) is located in the engine compartment and provides the SKIS engine control logic. ( Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES/POWERTRAIN CONTROL MODULE - DESCRIPTION ).
  • Security Indicator- A security indicator is integral to the ElectroMechanical Instrument Cluster (EMIC) (also known as the Cab Compartment Node/CCN). ( Refer to 8 - ELECTRICAL/INSTRUMENT CLUSTER/SECURITY INDICATOR - DESCRIPTION ).
  • Sentry Key Remote Entry Module (2)- The Sentry Key REmote Entry Module (SKREEM) (also known as the Sentry Key Immobilizer Module/SKIM or the Wireless Control Module/WCM) is located on the right side of the steering column near the ignition lock cylinder housing and an integral molded plastic antenna ring circles the ignition lock cylinder like a halo. The SKREEM and its antenna are concealed beneath the steering column shrouds. Two SKREEM modules are available: one for vehicles equipped with Remote Keyless Entry (RKE) only, and one for vehicles equipped with RKE and SKIS.
  • Sentry Key Transponder (3)- The Sentry Key transponder is contained within the Remote Keyless Entry (RKE) transmitter on the ignition key.
  • If you do not know about this , do not mess with it , take it to professional. Save your self money an aggravation !

Feb 07, 2015 | Cars & Trucks

1 Answer

I have a 96 ford conversion van with a 600 plus addon keyless system and need to program new keyless remots , need to know how to get system in program mode.


Hi.

To program ( or reprogram ) a keyless entry remote transmitter into the remote keyless entry module, perform the following steps:

1. Turn the key to ON or ACC and short the two terminals of the program connector, a two-pin connector located below the driver's side of the instrument panel at the base of the steering column. All doors should lock and then unlock.
2. Press any button on each keyless entry remote transmitter in turn. All doors should lock and then unlock. If the door locks do not respond, press the button again (up to three times maximum with the same keyless entry remote transmitter). If the door locks still fail to respond, go to Pinpoint Test A.
3. Repeat Step 2 to program additional keyless entry remote transmitters into the remote keyless entry module (up to four keyless entry remote transmitters maximum).
4. Turn key off.
5. Remove the short from the program connector. All doors should lock and then unlock.
6. Verify that the keyless entry remote transmitters have been successfully programmed by pressing the LOCK or UNLOCK button on each one, and observing that the system responds by locking and/or unlocking the doors.


I hope this helps you.

Thanks!

Nov 28, 2010 | 1996 Ford Econoline

1 Answer

Reprogram keyless remotes


There is no on board programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the key-less remote.

Dec 28, 2009 | 2005 Chevrolet Malibu Maxx

1 Answer

Where is the turn signal module on an 05 Malibu?


The modual is the trun signal it's self. Other than that it runs through the BCM and that distributs the power to the lamps.
Do the indiactors on the dash light up at all? Or do you just hear a clicking noise?

Dec 23, 2009 | 2005 Chevrolet Malibu Maxx

1 Answer

Doors automatically lock and unlock


It sounds like a keyless entry system. You may be sitting on an extra set of keys or if you have a keyless transmitter on your keychain that has loose batteries. Leave that keyless transmitter home and use you key to open the door. See if the problem goes away.

Jul 13, 2009 | 2005 Chevrolet Malibu Maxx

1 Answer

2005 F150 Keyless Entry


There is a technical service bulletin out on this probelm on 2004/2005 F150.
ISSUE: Some 2004-2005 F-150 vehicles built through 2/7/2005, may exhibit an inoperative keyless entry keypad. This may be due to the vehicle security module (VSM) not being configured to accept keyless entry keypad input.

The fix is to reprogam the vehicle security module with as-built data. So it would have to go to the dealer to do this.
The tsb number is 05-5-5.

Feb 21, 2009 | 2005 Ford F-150

1 Answer

Change battery/Reprogram remote


take the postive battery cable off then put it back on then turn your car over three times not start it but just turn it on off on off on off that should reset it. thats what they did to mine at the dealers and it cost me 120.00 bucks

Oct 28, 2008 | 2005 Chevrolet Malibu

1 Answer

Keyless entry


There are no wires you can touch to program key fob's , Dealer only ! Need a factory scan tool !
This procedure will erase all keyless entry transmitters from memory.
Install a scan tool.
Turn ON the ignition with the engine OFF.
With the scan tool, select Body.
Select Remote Control Door Lock Receiver (RCDLR).
Select Module Setup.
Select Program Key Fobs.
Select Invalidate All.
Follow the scan tool on screen instructions.

Jul 02, 2017 | 2007 Chevrolet Malibu SS Sedan New Cars

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...