Question about 2003 Chevrolet Impala

1 Answer

Need the steps to installing a new car battery in my 2003 impala.

Posted by on

  • yadayada
    yadayada May 11, 2010

    pull the old one out and put the new one in make sure it is all clean and free of corrision.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

First disconnect, NEGATIVE cable, than the positive cable. Than remove the bolt or strap that is securing battery. Then when you install new battery, Connect POSITIVE FIRST, then negative battery.
Make sure battery is charged before installing in vehicle. It will save lots of tear on altenator.

Posted on Jun 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 Chevy impala,,my battery light is on and the car keep cutting off,,I have a new alternator ams a brand new battery I'm trying to figure out the problem


Most parts stores will run a charging circuit diagnostic for free. You may have a blown fusible link in the charge circuit, or a short somewhere.

Jun 15, 2015 | 2003 Chevrolet Impala

3 Answers

Why is it that my 2003 impala will crank and turnover but wont start


I sounds like you have a fuel flow problem. Replace the in-line fuel filer located in the fuel line in front of the rear tire. Check out this web site for "how to" replace the in-line fuel filter.
http://www.ehow.com/how_6724057_install-filter-2003-chevy-impala.html

Aug 15, 2014 | 2003 Chevrolet Impala

1 Answer

How to replace waterpump


step 1. drain cooling system.
step 2. remove battery and battery tray.
step 3. remove drive belt.
step 4. remove water pump bolts ( 318 ).
step 5. remove water pump ( 300 ) and water pump gasket ( 314 ).discard gasket.
step 6. inspect and clean gasket mating serface.
step 7. install new water pump and gasket and tighten bolts to 89 in. lbs.
step 8. install drive belt.
step 9. install battery tray and battery.
step 10. fill cooling system.


Book time is 1.5 hours ( this one is what we call a gravy run ) good luck

1_18_2012_1_26_20_pm.jpg

Jan 13, 2012 | 2006 Chevrolet Impala

1 Answer

My 2003 chevy impala is hesitating to start sometimes stop while driving, my signal lights used to work but only when i push the hazards lights on and off now my signal lights dnt work, when i use them now...


I would go to Wal-mart and buy their best battery.. have them check to make sure the car is charging.....(if the battery happens to go bad... there is a Wal-mart everywhere and you can still get a new replacement battery at 3am)

Jul 08, 2017 | 2003 Chevrolet Impala

1 Answer

Need to change the battery in a 2003 Chevy Impala. How do I do this? take out and replace? thank you.


Yes you simply take the old one out and install the new one. Or you can, drive to your local Advance Auto Parts and purchase a new battery. They will remove the old battery and install the new one free of charge. Other Auto Parts Stores may do the same.

Jun 01, 2010 | 2003 Chevrolet Impala

1 Answer

2003 Impala: HOW DO I CHANGE BATTERY 2005 CHEVROLET IMPALA...


The battery is under the hood, just behind the passenger headlight.
There is a black bar that crosses over the battery and goes back towards strut tower. Remove this bar and the three bolts; probably a 12 or 13mm socket.
Remove the negative (black) battery cable with an 8mm socket or wrench. A 5/16" should work also.
Then remove the positive (red) cable with same socket.
Remove the battery clamp and bolt. Probably a 12mm socket with extension.
It's tight, but the battery can be removed.
Reverse instructions for installing the battery. (That includes hooking up the red battery cable first, then the black cable.)

May 16, 2010 | 2003 Chevrolet Impala

1 Answer

Need to replace turn signal switch,2003 chev impala


You only need to disconnect negative battery cable to make it safe to work on.

Mar 16, 2010 | 2003 Chevrolet Impala

1 Answer

I am trying to replace the headlights on my 2003 chevy impala.


You open your bonnet, remove the bulb, check the watts and replace with a higher wattage bulb.

Mar 18, 2009 | 2003 Chevrolet Impala

1 Answer

Replacing battery in 2003 chevy Impala steps needed


get the right size wrench that u need and remove the cables off of the battery take out the battery put in the new put hte black cable on first and then the red make sure there good and snug but dont overtighten them

Aug 23, 2008 | 2003 Chevrolet Impala

Not finding what you are looking for?
2003 Chevrolet Impala Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...