Question about 2014 RAM CV Tradesman

1 Answer

2014 Ram Cargo van - tighten serpintine belt?

How do I get to the serpintine belt to tighten it?

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

You don't ...if the belt is loose you need to replace the tensioner

Posted on Mar 02, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing serpintine belt, belt keeps slipping off, How can you fix? 1999 pontiac grand am


Sounds like the belt tightener unit is wore out and needs replacing.
As the bearings wear out the pulley will move around causing the belt to come off. When you replace the tightener you should replace the belt as well.

Jun 23, 2014 | 1991 Oldsmobile Cutlass Ciera

1 Answer

Nissan quest 2007 whining noise in hood


Your right its probably your serpintine belt. It is a cheap repair to have a mechanic tighten belts or replace if nessasary. Better that then be stranded. Its could also possibly be your power steering pump if your low on fluid. But that you should have noticed earlier each time you turned a corner.

Apr 14, 2012 | 2007 Nissan Quest 3.5 Minivan

1 Answer

CHANGING SERPINTINE BELT "98 WANGLER


Somewhere in the world there may be a specification for that but in reality, just make the pulley through bolt tight (without being and animal on it). The long jack bolt gets tightened first. There, you check belt deflection. You should have about one inch or slightly less deflection in the center of the longest run of the belt. After getting it to that point, lock it and tighten the pulley. Run it for a few minutes and then drive it. If the belt squeals, loosen the adjustment and give it a few more turns. Do not over-tighten it. A loose belt will be noisy. An overtightened one can destroy component bearings.

May 19, 2011 | 1998 Jeep Wrangler

1 Answer

Need to find out how to tighten the serpintine belt on a 99 pontiac montana 3.4 liter van


if that engine is not equipped with a automatic belt tensioner then there should be a pulley with a screw in the top of it loosen the bolt on the front then turn the screw on the top clockwise until the desired tension is reached.retighten the bolt on the front and youre ready to go.

Dec 11, 2009 | 2001 Pontiac Montana

1 Answer

I need a serpintine routing diagram please for a 2002 ford windstar.


2002 FORD TRUCK WINDSTAR 3.8L SFI 6CYL REPAIR GUIDE

Drive Belt Routings

12ff91b.jpg

Fig. Accessory drive belt routing-3.0L engine


e11fada.jpg

Fig. Accessory serpentine belt routing-3.0L engine


22c7396.jpg

Fig. Accessory serpentine belt routing-3.8L engine


I hope help you with this. Good luck.

Sep 14, 2009 | 2002 Ford Windstar Cargo

1 Answer

2000 WINDSTAR VAN SERPINTINE BELT TIGHTENING


the belt is tensioned by an automatic belt tensioner pulley assembly, so what is the problem with the tension? belt noise?

Jun 09, 2009 | 2001 Nissan Sentra

1 Answer

Replace serpintine belt


You shouldn't need to most of the time all you need is a 15mm wrench. Use it by turning the spring tightener inward toward the center of the motor than the belt should come off. Also when you take it off make sure you know how the belt goes around the pulleys so everything will work together like normal. when putting the belt on you should use the wrench to turn the tightener back inward and slip the belt back on and make sure it looks just like the old one when its on.

Jan 12, 2009 | 2003 Toyota Corolla

1 Answer

2002 Ram Cargo Van


mcdevito75 here, Maybe a timeing belt, Ignition system out of time, a bad intake valve. Have the dealership check all.

Sep 05, 2008 | 2002 Dodge Ram 3500 Truck

1 Answer

Nebettleed to change serpintine belt on a 2000 voltswagen


The easiest solution I can say would be to go to parts america or Advance Auto Parts during a non peak time and ask for help. These belts should be a 5 minute replacement and most store employees will enjoy offering you the free service just to get out of the store for a few minutes. SOME stores are more willing to help than others.

(If you over tighten the belt you will have problems and if you under tighten the belt you will have squeals. If you still wish to do this yourself just make sure the belt is tight enough that it only turns 90 degrees in the middle to the left of right when tightened.)

Aug 17, 2008 | 2000 Volkswagen Beetle

Not finding what you are looking for?
2014 RAM CV Tradesman Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top RAM Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Glenn Smart
Glenn Smart

Level 3 Expert

801 Answers

mcvann4

Level 1 Expert

40 Answers

Are you a RAM Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...