Question about 2005 Volkswagen New Beetle

1 Answer

ABS light-triangle with ! and curved arrow and check engine light

2005 turbo convertible with 26,000 miles. Have had 2 sensors replaced-the Mass Air Sensor and MIL sensor?- and the check engine light is still on. Mechanic said not to worry about ABS light, but I do. Have spent considerable money! What should I do next?

Posted by on

  • grovianartch Jun 22, 2009

    to the vw dealer i go-thank you, thank you!

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Volkswagen Master
  • 81,400 Answers

The sensors u had replaced will not affect the ABS brake system, while this light is on your Antilock Brake System is disabled, if u need this very important safety feature u are out of luck, have the system codes tested for the ABS and the check enhgine light, go to a VW dealer, don't waste your time on any technician who says to ignore an ABS light warning!!

Posted on Jun 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

2003 Nissan Altima 2.5L Service Engine Soon Light is on, Auto Zone says codes are for MAF and O2 Sensors. Car hard to start after driving a while but when starts appears to run smooth. Auto Zone thi


ok lets start with the codes they say your getting. P??? which 1's and how many. there are few o2 sensors, are they next to the Exhaust next to the converter? MASS AIR FLOW -MAF use this, for now i am guessing, until i see the correct codes your are getting. this could be the 1 you may have below, please read it........
  • P0103
    Mass Air Flow Sensor Circuit High Input
  • Possible causes
  • Faulty mass air flow sensor
    - Intake air leaks
    - Dirty mass air flow sensor
    - Dirty mass air filter
    - Mass air flow sensor harness is open or shorted
    - Mass air flow sensor circuit poor electrical connection
  • Before replacing the mass air flow sensor, try replacing the air filter and cleaning the air flow sensor with low compress air or mass air flow sensor cleaner. Reset code and drive vehicle. If the code comes back, it may be necessary to replaced the mass air flow sensor.
  • possible symptoms Engine Light ON (or Service Engine Soon Warning Light)
    - Engine stall
    - Engine running rough
    - Excessive fuel consumption
    - Excessive smoke
  • the code is generated when An excessively high voltage from the sensor is sent to Engine Control Module (ECM).
2003 NISSAN Altima Sedan OBDII Codes List

Oct 22, 2014 | 2003 Nissan Altima

1 Answer

I have a 1986 gts corrolla that will not run unless air flow meter is held open


Now if your old fuel pump was loosing pressure it tends to lean out Overheating your catalytic converter and melting it so exhaust gasses can't flow To test this is easy just remove the two bolts holding it on the engine pipe Start the engine if runs fine replace cat converter

Sep 15, 2012 | 1986 Toyota Corolla 2 Door

2 Answers

Check engine light low voltage o2 sensor 04 chevy ventura


your code must be P0131, a P0131 code refers to the first oxygen sensor on Bank 1. P0131 means the O2 oxygen sensor's voltage remained low for longer than 2 minutes. This is interpreted by the ECM as a low voltage condition and sets the MIL. Bank 1 Sensor 1 is located in front of the catalytic converter.
The solution is you can:
1.Replace faulty sensor.
2.Repair short, open, or high resistance on o2 signal circuit. FB.init("dd7d9e9681341cde77587bc6a2029f6f"); OBD-Codes.com on Facebook

Jul 02, 2011 | 2004 Chevrolet Venture Passanger

1 Answer

2002 Toyota Rav4....check engine light""is


Here are two of the most common causes of the check engine light.

Most common, MAF ( mass air flow ), sensor. A faulty MAF prevents the computer from determining the correct fuel/air mix ratio.

Oxygen sensor. ( front and rear, front meaning before the catalytic converter, rear meaning after the catalitic converter. The front measures the fuel/air mix being sent through the catalitic converter, the back measures the emmisions and lets the computer know if any fuel/air mix ratios need to be adjusted. Both of these can trigger the check engine light.

I hope this helps you.

Feb 02, 2011 | 2002 Toyota RAV4

1 Answer

My 2006 VW TURBO TDI is sick- Help me


Changed the timing belt and knocked loose the wires or connections to the sensors on the mass airflow device.

Mar 03, 2017 | 2006 Volkswagen Jetta

1 Answer

I have a 2005 Chrysler Town & Country with almost 100,000 miles. The check engine light came on about 2 months ago and the code said the O2 sensors needed to be replaced. About a month later, the...


there are no codes that say replace O2 sensors,or remove converter,Thats just somebody's guessing,When it says O2 sensor that tells the mechanic to look for trouble in that area,wiring or faulty readings,And there are four O2 sensors.

Jan 20, 2010 | 2005 Chrysler Town & Country

2 Answers

2005 Pt Cruiser idles rough at stop lights/ poor gas mileage.


i hav a 2003 pt cruiser 2.2 crd touring it wont go over 3000 revs engine light cums on. error code p0243 i hav replaced wastegate solenoids cleaned egr valve cud it be the mass air flow sensor that has a problem thanx

Sep 18, 2009 | 2005 Chrysler PT Cruiser

1 Answer

Xterra repair


Since this is an intermittent problem, first try to determine if the problem arises due to one of these many intermittent problems:

* Vehicle vibration
* Heat sensitive
* Freezing
* Water intrusion
* Electrical load
* Cold or hot start up

If you can't isolate the cause of the intermittent problem, you can try adjusting the Idle Speed/Ignition Timing/Idle Mixture Ratio:

Idle Speed/Ignition Timing/Idle Mixture Ratio Adjustment

PREPARATION
1) Make sure that the following parts are in good order.

* Battery
* Ignition system
* Engine oil and coolant levels
* Fuses
* ECM harness connector
* Vacuum hoses
* Air intake system
* (Oil filler cap, oil level gauge, etc.)
* Fuel pressure
* Engine compression
* EGR valve operation (If so equipped)
* Throttle valve
* Evaporative emission system

2) On air conditioner equipped models, checks should be carried out while the air conditioner is OFF.
3) On automatic transmission equipped models, when checking idle rpm, ignition timing and mixture ratio,
checks should be carried out while shift lever is in “N” position.
4) When measuring “CO” percentage, insert probe more than 40 cm (15.7 in) into tail pipe.
5) Turn off headlamps, heater blower, rear defogger.
6) Keep front wheels pointed straight ahead.
7) Make the check after the cooling fan has stopped.

INSPECTION PROCEDURE

1 INSPECTION START
1. Visually check the following:
I Air cleaner clogging
I Hoses and ducts for leaks
I EGR valve operation (If so equipped)
I Electrical connectors
I Gasket
I Throttle valve and throttle position sensor operation
2. Start engine and warm it up until engine coolant temperature indicator points to the middle of gauge.
Ensure engine stays below 1,000 rpm.
3. Open engine hood and run engine at about 2,000 rpm for about 2 minutes under no-load.
4. Perform diagnostic test mode II (Self-diagnostic results).
OK or NG
OK ' GO TO 2.
NG ' 1. Repair or replace components as necessary.
2. GO TO 2.

2 CHECK IGNITION TIMING
1. Run engine at about 2,000 rpm for about 2 minutes under no-load.
2. Rev engine (2,000 to 3,000 rpm) two or three times under no-load, then run engine at idle speed.
3. Turn off engine and disconnect throttle position sensor harness connector.
4. Start and rev engine (2,000 - 3,000 rpm) two or three times under no-load, then run at idle speed.
5. Check ignition timing with a timing light.
15°±2° BTDC (in “P” or “N” position)
OK or NG
OK ' GO TO 4.
NG ' GO TO 3.

3 ADJUST IGNITION TIMING
1. Adjust ignition timing by turning distributor after loosening securing bolts.
2. Turn off engine and connect throttle position sensor harness connector to throttle position sensor.
' GO TO 2.


4 CHECK BASE IDLE SPEED
1. Check idle speed.
700±50 rpm (in “P” or “N” position)
OK or NG
OK ' GO TO 6.
NG ' GO TO 5.

5 ADJUST BASE IDLE SPEED
1. Rev engine (2,000 to 3,000 rpm) 2 or 3 times under no-load then run engine at idle speed.
2. Adjust idle speed by turning idle speed adjusting screw.
700±50 rpm (in “P” or “N” position)
' GO TO 6.

6 CHECK TARGET IDLE SPEED
1. Turn off engine and connect throttle position sensor harness connector.
2. Start and rev engine (2,000 to 3,000 rpm) 2 or 3 times under no-load then run at idle speed.
3. Check idle speed.
750±50 rpm (in “P” or “N” position)
OK or NG
OK ' GO TO 9.
NG ' GO TO 7.

7 DETECT MALFUNCTIONING PART
Check the following.
1. Check IACV-AAC valve and replace if necessary.
2. Check IACV-AAC valve harness and repair if necessary.
3. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 9.

9 CHECK FRONT HEATED OXYGEN SENSOR LH SIGNAL
1. Run engine at about 2,000 rpm for about 2 minutes under no-load.
2. Set “Left bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
3. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' GO TO 12.
NG (MIL does not blink.) ' GO TO 17.
NG (MIL blinks less than 5 times.)
' 1. Replace front heated oxygen sensor LH.
2. GO TO 10.


10 CHECK FRONT HEATED OXYGEN SENSOR LH SIGNAL
1. Warm engine to normal operating temperature.
2. Run engine at approx. 2000 rpm for approx. 2 minutes under no-load.
3. Set “Left bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
4. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' GO TO 13.
NG ' GO TO 11.

11 DETECT MALFUNCTIONING PART
Check the following.
1. Check fuel pressure regulator.
2. Check mass air flow sensor and its circuit.
3. Check injector and its circuit.
Clean or replace if necessary.
4. Check engine coolant temperature sensor and its circuit.
5. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 2.


13 CHECK FRONT HEATED OXYGEN SENSOR RH SIGNAL
1. Set “Right bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
2. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' INSPECTION END
NG (MIL does not blink.) ' GO TO 16.
NG (MIL blinks less than 5 times.)
' 1. Replace front heated oxygen sensor RH.
2. GO TO 14.


14 CHECK FRONT HEATED OXYGEN SENSOR RH SIGNAL
1. Warm engine to normal operating temperature.
2. Run engine at approx. 2000 rpm for approx. 2 minutes under no-load.
3. Set “Right bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
4. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' INSPECTION END
NG ' GO TO 15.

15 DETECT MALFUNCTIONING PART
Check the following.
1. Check fuel pressure regulator.
2. Check mass air flow sensor and its circuit.
3. Check injector and its circuit. Clean or replace if necessary.
4. Check engine coolant temperature sensor and its circuit.
5. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 2.
16 CHECK FRONT HEATED OXYGEN SENSOR RH HARNESS
1. Turn off engine and disconnect battery ground cable.
2. Disconnect ECM harness connector.
3. Disconnect front heated oxygen sensor RH harness connector.
4. Check harness continuity between ECM terminal 50 and front heated oxygen sensor RH harness connector.
Continuity should exist.
OK or NG
OK ' 1. Connect ECM harness connector.
2. GO TO 18.
NG ' 1. Repair or replace harness.
2. GO TO 9.

17 CHECK FRONT HEATED OXYGEN SENSOR LH HARNESS
1. Turn off engine and disconnect battery ground cable.
2. Disconnect ECM harness connector.
3. Disconnect front heated oxygen sensor LH harness connector.
4. Check harness continuity between ECM terminal 51 and front heated oxygen sensor LH harness connector.
Continuity should exist.
OK or NG
OK ' 1. Connect ECM harness connector.
2. GO TO 18.
NG ' 1. Repair or replace harness.
2. GO TO 9.

18 PREPARATION FOR “CO” % CHECK
1. Disconnect engine coolant temperature sensor harness connector.
2. Connect a resistor (4.4 kW) between terminals of engine coolant temperature sensor harness connector.
' GO TO 19.

19 CHECK “CO” %
1. Start engine and warm it up until engine coolant temperature indicator points to the middle of gauge.
2. Rev engine (2,000 to 3,000 rpm) two or three times under no-load, then run engine at idle speed.
3. Check “CO” %.
Idle CO: 1.5 - 9%
After checking CO%,
a. Disconnect the resistor from terminals of engine coolant temperature sensor.
b. Connect engine coolant temperature sensor harness connector to engine coolant temperature sensor.
OK or NG
OK ' 1. Replace front heated oxygen sensor LH.
2. GO TO 10.
NG ' GO TO 20.

20 DETECT MALFUNCTIONING PART
Check the following.
1. Connect front heated oxygen sensor harness connectors to front heated oxygen sensors.
2. Check fuel pressure regulator.
3. Check mass air flow sensor and its circuit.
4. Check injector and its circuit.
Clean or replace if necessary.
5. Check engine coolant temperature sensor and its circuit.
6. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 2.

Aug 17, 2008 | 2000 Nissan Xterra

4 Answers

2001 toyota corolla check engine light is on. Code reads P420 low threshold. Changed front and rear Oxygen sensors reset the light and drove the car 50 miles and the light came back on. the car will not...


Mass Air Flow sensor! Just remove your air filter cover. Go to Auto Zone and purchase some solvent. Spray past the air filter and it should correct the problem. If not, replace the Mass air-flow sensor. This is commonly mistaken for an oxygen sensor. Mine did this and I followed these steps and it fixed the light. BTW, the light stayed on for 5 years before I fixed it. Never hurt anything. It's normally something to do with emissions. Dummy lights. :)

Aug 06, 2008 | 2000 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

410 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Marvin
Marvin

Level 3 Expert

81400 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...