Question about Ford Fusion

Open Question

Where is the hazard switch located in the ford fusion hybrid

Posted by Anonymous on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 70 Answers

SOURCE: I need to locate the air senor switch in a 2008

The mass air flow sensor is in the air intake tube at the lower left corner of the engine compartment. Please rate this info That will help me THankyou RJ

Posted on May 30, 2010

  • 42847 Answers

SOURCE: broken hazard switch on ford fusion

Most likely the switch has to be replaced. It should have a push 0 - push off action.

Posted on Sep 07, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What is the rumble on braking in rear of my 2010 fusion hybrid 100k miles?

it could be the drum/rotor is warped causing the noise or the pads/shoes have gone hard or rust build up on the edges causing it as well. either way have the brakes checked for condition.

Sep 25, 2014 | 2010 Ford Fusion Hybrid

1 Answer

What does a po130 code on 2010 Ford Fusion Hybrid mean?

Possible causes
- Faulty Front Heated Oxygen Sensor Bank 1
- Front Heated Oxygen Sensor Bank 1 harness is open or shorted
- Front Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks
Tech notes
Replacing the O2 Sensor 1 usually takes care of the problem

Jul 27, 2014 | 2010 Ford Fusion Hybrid

1 Answer

Dead battery on 2013 fusion after couple of days not using it

battery needs charged and retested. if not ok then replace battery and have ford dealer reset bms (battery monitor system). problem will go away.

Jan 12, 2014 | 2013 Ford Ford Fusion Hybrid

1 Answer

Windshield washer clogged on 2011 Ford Fusion Hybrid

Have you tried pole a piece of wire like off a wire brush into the hole? I know it sounds silly, but most times what clogs the outlets is wax when you wax the car.

Dec 07, 2013 | 2011 Ford Fusion Hybrid

1 Answer

How to reset ford fusion 2013 tpms

Did you try to disconnect your NEGITIVE battery cable for about 1 minute? You can buy a reset tool or go by a tire shop that can do that also

Nov 30, 2013 | 2013 Ford Ford Fusion Hybrid

1 Answer

Flasher relay location for ford fusion 2006

On my Ford Focus, the turn-signal electronics were integrated into the hazard switch assembly.

Jul 05, 2013 | 2006 Ford Fusion

1 Answer

Where is the location of the inertia switch?

should be behind the passenger side kick panel in floorboard

May 25, 2013 | 2013 Ford Ford Fusion Hybrid

1 Answer

Broken hazard switch on ford fusion

Most likely the switch has to be replaced. It should have a push 0 - push off action.

Sep 07, 2012 | Ford Fusion Cars & Trucks

1 Answer

2010 Ford Fusion - After changing the oil, how do I extinguish the oil change warning?

You use the "Setup" and "Reset" buttons in the Information Center. The sequence of button-pushing is different for Hybrid and Non-Hybrid vehicles. The sequence for your car should be outlined in your Owner's Manual.

Dec 07, 2010 | 2011 Ford Fusion

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5675 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides