Question about 2007 Chevrolet Kalos 1.4

Open Question

What causes the gear shift to lock in the parking position

My car is kalos 1.4 automatic 2008

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 299 Answers

SOURCE: gear shift lock

Most probable cause is shift interlock solenoid,generally located on shifter assebly,requires removal of console.Then will be electric solenoid located at lower part of shifter.May also be brk switch at pedal.

Posted on Jun 17, 2009

Ad
  • 8 Answers

SOURCE: My 2006 Chevy cobalt key will not turn completely

ur gear shift has a little plastic bar on gear shift and it has crack on the side u cant see have it changed out and both of ur problems will be solved at same time.

Posted on Jul 07, 2009

shop510
  • 90 Answers

SOURCE: I parked my 2003 Chevy Trailblazer in my driveway

If it is floor shift it has a soloind under the cover not to hard to remove, you have to memove the whole thing bolt in front cupholder and inside armrest storage. once it has removed there is a soloind in there that mounts on the shifter. this goes bad alot. Push the button on the silver soloind button this will release it into gear. Hope this helps. ( Usually he black soloind goes bad)

Posted on Sep 27, 2009

  • 1 Answer

SOURCE: I have a 2002 Chevy

tengo un problema con mi cavalier 2001. cuando el ventilador enciende prende una luz que indica trac off. luego empiesa a fallar el carro tarda para avansar le piso y se siente como si fuera en nutrial y avienta el cambio brusca mente y se apaga el motor.<!-- from fixya rte -->

Posted on Aug 14, 2010

  • 1 Answer

SOURCE: I have a 2008 chevy

It could be a few things....I just had this same problem with my 2008 chevy aveo this week. Also, my check engine light came on the very next day after the gear shifter started locking. I called Bob Bell and they told me that the gear shifter locking is probably due to a sensor going bad that tells your car it is in park. However, after taking my car to my brother-in-law (who has very LITTLe knowledge about repairing cars), we discovered that my brake lights were not working either. He told me that is why my check engine light is on - because it is extremely dangerous to drive without brake lights. We checked the fuses to make sure there was no fuse blown and they were all just fine. So bottom line, the problem was that there is a brake switch under your dash board where your brake is. My switch keeps sticking and will probably eventually need to be replaced. When the switch works properly, my brake lights work fine, my gear shifter unlocks and my check engine light goes out. Not sure how much it is to fix this switch if that is the problem but I hope it helps!

Posted on Jan 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When i put my car in park or drive it feels like it is hard to move the shifter. 2008 saturn aura


Safety system , shift lock . Has locking solenoid's that won't allow shifting from park to gear without the diver pressing on the brake pedal . Electrically controlled , brake switch , body control module .
Your best bet would be to take it to a qualified repair shop .
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
• The automatic transmission shift lock solenoid (serviced as the automatic transmission shift lock actuator), as well as the body control module (BCM) and the engine control module (ECM). The shift lock solenoid is located within the floor shift control assembly with vehicles equipped with floor shift.
• The BCM controls the voltage supply circuit of the shift lock control solenoid. The following conditions must be met before the BCM will supply voltage to the shift lock control solenoid.
The BCM controls the voltage to the shift lock control solenoid through the shift lock control solenoid controlled voltage circuit. The following conditions must be met before the BCM will supply voltage to the shift lock solenoid:

Sep 19, 2017 | Saturn Cars & Trucks

2 Answers

05 Trailblazer transmission says neutral but gear shiftier is locked in park.


Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
• The automatic transmission shift lock control solenoid
• The automatic transmission shift lock control switch
With the ignition in the ON position, voltage is supplied to automatic transmission shift lock control switch. Voltage flows through the normally closed contacts of the automatic transmission shift lock control switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid causing the transmission shift lever to be physically locked in the PARK position. When the brake pedal is pressed the contacts in the automatic transmission shift lock control switch open, de-energizing the automatic transmission shift lock control solenoid. This allows the shift lever to be move out of the PARK position.

Circuit Description
The transmission range (TR) switch is part of the park/neutral position (PNP) and back-up lamp switch assembly, which is externally mounted on the transmission manual shaft. The TR switch contains four internal switches that indicate the transmission gear range selector lever position. The powertrain control module (PCM) supplies ignition voltage to each switch circuit. As the gear range selector lever is moved, the state of each switch may change, causing the circuit to open or close. An open circuit or switch indicates a high voltage signal. A closed circuit or switch indicates a low voltage signal. The PCM detects the selected gear range by deciphering the combination of the voltage signals. The PCM compares the actual voltage combination of the switch signals to a TR switch combination chart stored in memory.

These are all electronically controlled , yur best bet would be to take your vehicle to the dealer .

Apr 19, 2017 | 2005 Chevrolet TrailBlazer

1 Answer

2000 regal won't go out of park


I would think it has something to do with
Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consist of the following components:
• The automatic transmission shift lock control solenoid.
• The automatic transmission park lock solenoid (Regal only).
• The automatic transmission shift lock control switch.
• The transmission range switch.

Regal
With the ignition in the ON position, battery positive voltage is supplied to the automatic transmission shift lock control switch. The circuit continues through the normally-closed switch to the automatic transmission shift lock control and park lock solenoids. The transmission range switch provides a path to ground in the PARK position. With the automatic transmission shift lock control and park lock solenoids energized the shift lever is locked in the PARK position. When the driver presses the brake pedal, the contacts in the automatic transmission shift lock control switch open. This causes the automatic transmission shift lock control and park lock solenoids to release. This allows the shift lever to move from the PARK position.
Do the brake lights work ? If not could be cause by bad brake light switch .

Nov 28, 2016 | 2000 Buick Regal

2 Answers

This morning it started fine but will not come out of gear and my airbag light is on. Someone said it was the fuse but I am not sure which fuse. Any ideas ?


I am mechanic I really need to no more make ect. but it could be battery or the ignition switch or ignition lock n key but like I said need more information this is a guess that I told you

Oct 21, 2015 | 2008 Chevrolet Chevrolet TrailBlazer LT

1 Answer

Stuck in park will not shift


Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control is a safety device that prevents an inadvertent shift out of PARK when the ignition is ON. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid.


?€¢
The automatic transmission shift lock control switch.


?€¢
The park/neutral position switch.

With the ignition in the ON position, battery positive voltage is supplied to the park/neutral position switch. When the transmission is in the PARK position the contacts in the park/neutral position switch are closed. This allows current to flow through the switch to the automatic transmission shift lock control switch. The circuit continues through the normally-closed switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid, locking the shift linkage in the PARK position. When the driver presses the brake pedal the contacts in the automatic transmission shift lock control switch open, causing the automatic transmission shift lock control solenoid to release. This allows the shift lever to move from the PARK position.
Park Lock Solenoid
The park lock solenoid is a safety device that prevents an inadvertent shift out of PARK when the key is in the OFF position. The key must be in the RUN position to release the park lock solenoid. The system consists of the park lock solenoid. With the ignition in the ON position, voltage is supplied to the park lock solenoid. The park lock solenoid energizes through a permanent ground unlocking the shift lever. With the ignition in the OFF or ACCY position the park lock solenoid de-energizes and locks the shift lever in the park position.
Shift Lever Does Not Move with Brake Pedal Depressed
DEFINITION: Transmission shift lever will not move out of the PARK position with the ignition ON and the brake pedal pressed.

1

Did you perform the Symptoms - Automatic Transmission Shift Lock Control tests and all the necessary inspection?
Go to Step 2
Go to Symptoms - Automatic Transmission Shift Lock Control

2

  1. Turn ON the ignition, with the engine OFF.
  2. Press and hold the brake pedal.
  3. Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO Go to Step 3

3

  1. Turn OFF the ignition.
  2. Disconnect the automatic transmission shift lock control switch.
  3. Turn ON the ignition, with the engine OFF.
  4. Press and hold the brake pedal.
  5. Attempt to move the transmission shift lever out of the PARK position.
Does the transmission shift lever move out of the PARK position?
Go to Step 6
Go to Step 4

4

  1. Turn OFF the ignition.
  2. Disconnect the automatic transmission shift lock control solenoid.
  3. Turn ON the ignition, with the engine OFF
  4. Press and hold the brake pedal.
  5. Attempt to move the transmission shift lever out of the PARK position.
Does the transmission shift lever move out of the PARK position?
Go to Step 7
Go to Step 5
Inspect for poor connections at the harness connector of the automatic transmission shift lock control solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 10
Go to Step 9

6

Inspect for poor connections at the harness connector of the automatic transmission shift lock control switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 10
Go to Step 8

7

Repair the short to battery positive voltage in the A/T shift lock control solenoid supply voltage circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 10
--

8

Replace the automatic transmission shift lock control switch. Refer to Stop Lamp Switch Replacement in Lighting Systems.
Did you complete the replacement?

Oct 13, 2015 | 2006 Hummer H2

1 Answer

How do I get unstuck from park?


Vehicles have a safety system that won't allow gear selector to be moved out of park unless brake pedal is pushed ! This what Buick calls there's
Automatic Transmission Shift Lock Control ! Depending on make of your vehicle it mite be called something else . But all vehicles have it.
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the ignition is ON. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid


?€¢
The automatic transmission shift lock control switch


?€¢
The brake to shift relay


?€¢
The rear integration module (RIM)

With the ignition in the ON position, battery positive voltage is supplied to the brake to shift relay coil. When the RIM energizes the brake to shift relay, the brake to shift relay switch contacts close suppling battery voltage to the automatic transmission shift lock control switch. The circuit continues through the normally closed switch to the automatic transmission shift lock control solenoid. The permanently grounded solenoid is energized. This locks the shift linkage in the PARK position. When the driver presses the brake pedal, the contacts in the automatic transmission shift lock control switch open. This causes the automatic transmission shift lock control solenoid to release. This allows the shift lever to move from the PARK position.

Sep 08, 2015 | Cars & Trucks

1 Answer

Shifter is locked in park on a 2002 bravada that sayes on dash its in reverse


PRND321 Display
The instrument panel cluster (IPC) displays the selected gear position as determined by the engine control module (ECM). The IPC - instrument panel cluster receives a serial data message from the ECM indicating the gear position. The PRND321 display blanks if:
?€¢
The ECM detects a malfunction in the transmission range switch circuit.


?€¢
The IPC detects a loss of serial data communications with the ECM. The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid


?€¢
The automatic transmission shift lock control switch

With the ignition in the ON position, voltage is supplied to automatic transmission shift lock control switch. Voltage flows through the normally closed contacts of the automatic transmission shift lock control switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid causing the transmission shift lever to be physically locked in the PARK position. When the brake pedal is pressed the contacts in the automatic transmission shift lock control switch open, de-energizing the automatic transmission shift lock control solenoid. This allows the shift lever to be move out of the PARK position.
The transmission range (TR) switch is part of the park/neutral position (PNP) and backup lamp switch assembly, which is externally mounted on the transmission manual shaft. The TR switch contains four internal switches that indicate the transmission gear range selector lever position. The PCM supplies ignition voltage to each switch circuit. As the gear range selector lever is moved, the state of each switch may change, causing the circuit to open or close. An open circuit or switch indicates a high voltage signal. A closed circuit or switch indicates a low voltage signal. The PCM detects the selected gear range by deciphering the combination of the voltage signals. The PCM compares the actual voltage combination of the switch signals to a TR switch combination chart stored in memory.
You need a Tech2 scan tool to diagnose this problem ! possible range sensor !

Sep 03, 2015 | Cars & Trucks

1 Answer

Abs light on wont shift out of park


Hi Judy , what kind of vehicle do you have ? Year an model ? ABS light has nothing to do with it not coming out of park . Problem with automatic transmission shift lock control ! Probably !
The automatic transmission shift lock control is a safety device that prevents an inadvertent shift out of PARK when the ignition is ON. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid.


?€¢
The automatic transmission shift lock control switch.


?€¢
The park/neutral safety switch.

With the ignition in the ON position, battery positive voltage is supplied to the automatic transmission shift lock control switch. The circuit continues through the normally-closed switch to the automatic transmission shift lock control solenoid. The park/neutral safety switch provides a path to ground for the automatic transmission shift lock control solenoid in the PARK position. This energizes the automatic transmission shift lock control solenoid, mechanically locking the shift linkage in the PARK position. When the driver presses the brake pedal the contacts in the automatic transmission shift lock control switch open, causing the automatic transmission shift lock control solenoid to de-energize. This allows the shift lever to move from the PARK position. When the shift lever is out of the PARK position the contacts in the neutral safety switch open and the automatic transmission shift lock control solenoid is de-energized.

Jul 07, 2015 | Cars & Trucks

1 Answer

The Key FOB is stuck in the ignition. How can I get it to eject?


Most if not all vehicles have a Electronic Park Lock (EPL)/Ignition Lock Cylinder Control Actuator: If the vehicle is equipped with automatic transmission and a floor mounted console gear shift, it has an ignition lock cylinder control actuator system in the steering column. The ignition lock cylinder control actuator purpose is to prevent the ignition key from being turned to the OFF position when the transmission is in any position other than PARK and the vehicle may still be moving. The column ignition lock system consists of an ignition lock cylinder control actuator, and a park position switch that is located in the automatic transmission shift lock control switch. The ignition lock cylinder control actuator contains a pin that is spring loaded to mechanically prevent the ignition key cylinder from being turned to the lock position when the vehicle transmission is not in the PARK position. If vehicle power is lost, and/or the transmission is not in the PARK position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column. Or it has
Linear Shift Assembly: If the vehicle is equipped with a column mounted gear shift, it has a linear shift assembly on the steering column. The linear shift assembly has a cable that runs from the linear shift assembly to the ignition lock cylinder case. The purpose of this cable is to prevent the ignition key from being turned to the OFF position when the transmission is in gear and the vehicle may still be moving. The linear shift assembly cable contains a pin that is spring loaded to mechanically prevent the ignition key cylinder from being turned to the lock position when the vehicle transmission is not in the PARK position. If vehicle power is lost, and/or the transmission is not in the PARK position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column.
Your best bet is to take it to a ASE certified repair shop or the dealer ! The fix involves taking the steering column apart an or the floor shifter assembly ! Also electrical test to determine what is the problem !
Your

Jul 04, 2015 | 2008 Volvo S80

1 Answer

The gear shifter on my 1998 Pontiac SE coupe will not unlock so I can take the car out of park


Do you have column or floor shifter ?
All automatic transaxle models use an electric park lock system. Within the housing assembly, a lock cylinder is connected to an actuator which rotates and engages on the electric park lock solenoid. When the floor-shift lever is not in the park position, the actuator disengages from the electric park lock solenoid slider. This allows the lock cylinder to move to the lock position. With the shift lever in PARK and the lock cylinder in LOCK, the actuator cam is positioned against the electric park lock solenoid slider. This prevents the shift lever from shifting out of the PARK position.
The column-shift automatic transaxle model uses a flexible cable actuator instead of an electric park lock system. One end of the cable is attached to the gate assembly. The other end of the cable is attached to the column mounted housing assembly. This system functions similarly to the floor-shift ignition lock system.
The manual transaxle model uses a push button lock cylinder. A clutch start switch is used. The clutch pedal must be pressed before the engine will crank. Refer to Park Lock System Check .
CAN you turn the key on ?
The gear selector does not shift out of PARK with the brake pedal depressed and the ignition switch in RUN.
Automatic Transmission Shift Lock Control Always On with Ignition in Run
Action
Value(s)
Yes
No

1

Was the BTSI System Check performed?
--
Go to Step 2
Go to Automatic Transmission Shift Lock Control System Check

2

Is this a column shift vehicle?
--
Go to Step 3 yes
Go to Step 4 no

3

  1. Move the gear selector to the PARK position.
  2. Disconnect the automatic transaxle control connector
  3. Turn the ignition switch to RUN.
  4. Connect the test lamp between terminal B and ground.
Does the test lamp light?
--
Go to Step 4
Go to Step 8

4

  1. Disconnect the brake switch connector C2.
  2. Move the ignition switch to RUN.
Can you shift the transaxle out of the PARK position?
--
Go to Step 5
Go to Step 8

5

Is the brake switch adjusted properly?
--
Go to Step 6
Go to Step 7

6

Replace the brake switch.
Is the repair complete?
--
System OK
--

7

Adjust the brake switch.
Is the repair complete?
--
System OK
--

8

  1. Disconnect the BTSI solenoid connector (column shift vehicles) or disconnect the automatic transaxle control connector (console shift vehicles).
  2. Move the ignition switch to RUN.
Can you shift the transaxle out of the PARK position?
--
Go to Step 9
Go to Step 10

9

Repair the short to power in CKT 1135.
Is the repair complete?
--
System OK
--

10

Test for sticking or binding in the shift linkage.
Does the shift linkage stick or bind?
--
Go to Step 11
Go to Step 12

11

Repair the shift linkage.
Is the repair complete?
--
System OK
--

12

Replace the BTSI solenoid (column shift vehicles) or replace the automatic transaxle control (console shift vehicles).
Is the repair complete?
--
System OK
Go to Step 1

May 18, 2015 | Pontiac Cars & Trucks

Not finding what you are looking for?
2007 Chevrolet Kalos 1.4 Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...