Question about 1993 Jeep Wrangler

1 Answer

1993 Jeep Wrangler Fuse #12 melted and that's the one that goes to the heater and A/C do i replace the fuse or get professional help?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 65 Answers

Well you can try and replace the fuse, but it might burn the vehicle to the ground or might not. If the fuse has melted then I would guess that there is not much voltage going through that circuit, since if it was amps the fuse would have simply blown.
If this is the case then replacing the fuse won't help, go to a good shop and tell them all you can. To find a good shop ask around to friends and see where they have gone or go and talk to the shop and see if they give you straight answers or a bunch of things you don't understadn. I find a good shop can usually explain things clearly and simply without insulting your intelligence.
Best of luck

Posted on Jun 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to know what a certain fuse is for on a 93 jeep wrangler


check you manual, fuse box cover and clean the contacts on the fuse box and where it plugs in

Jul 30, 2017 | 1993 Jeep Wrangler

1 Answer

2005 Jeep Wrangler Heater and Cigarette Lighters not working.


May help - fuses supply power but also needed is earth return to battery. This is usually black wires running from device to the car metal. To diagnose you need a multimeter. Check body of cigar lighter is connected to the chasis with meter on ohms. (continuity test) good is zero ohms. If earth problem, check under dash to ensure all earth wires connect to metal chassis. Then with ignition on, check centre pin at back inside cigar lighter has 12 volts to side.
If not then check fuse has 12 volt to it, Now you can get to the fan, repeat all the tests on fan. Best wishes, its tedious work.

Jan 03, 2014 | 2005 Jeep Wrangler

1 Answer

93 4.0L wrangler blower motor works when hot wired direct. No voltage at heater fuse mini-fuse box under dash? Where do I track voltage backward from there?


The 25amp blower fuse is powered thru the key switch.
Do you have power at the key switch for that circuit when it is in the on position ?

Apr 20, 2013 | 1993 Jeep Wrangler

1 Answer

I just bought a 1993 jeep wrangler 4wd. The only thing is the horn isn't working. How can I fix this?


First check that the fuse for the horn is good and if it is you will need to replace the horn relay that is found in the under hood high amp fuse box.

Feb 22, 2011 | 1993 Jeep Wrangler

1 Answer

Tail lights and parking lights not working on a 1993 jeep wrangler...replaced fuse


do you have a trailer wiring harness installed? very often this is poorly done, a causes a lot of problems with rear exterior lights.

Dec 21, 2010 | 1993 Jeep Wrangler

1 Answer

2000 A6 BLOWS #25 FUSE


A/C keeps blowing the fuse after I got it recharged. Its the R-12 system and it seemed to be ok before but now I got it recharged and replaced the blower motor in the front and now as soon as I turn it on it blows the fuse. I replaced the 3 fuse black and even rewired the fuses then took off the connectors tot he rotary switch and replaced those but it still blows the fuse. Any suggestions?

Could I have messed something up on installing the blower motor. __________________
Currently own:
1980 911SC slantnose
1991 Honda Accord -daily driver (1991 Honda Accord #2 - just because)
2003 Acura TL Type-S (2006 Honda Odyssey w/ DVD)

Gone but missed:
1988 Mazda RX-7 Turbo II (1991 Jeep Wrangler Renegade)
1984 Jeep CJ-7 (1994 Chevy Blazer)
1987 Chevy Corvette (1996 Mustang Cobra)
1993 Jeep Wrangler (1995 Mustang GT Conv.)
2003 Ford Explorer Sport Trac (1987 BMW M6)


Future: Hopefully not too far off
Ferrari Testarossa (Lamboghini Diablo or Countach)
please comment on these solution

Dec 20, 2010 | Audi A6 Cars & Trucks

1 Answer

THE PROBLEM IS WHEN YOU HIT A BUMP IT BLOWS THE #12 FUSE AND DIES REPLACE THE FUSE AND IT WILL START


u have wires shorting together when the vehicle is shook that needs to be sorted now or it could melt the wiring loom

Apr 16, 2010 | 2000 Jeep Wrangler

1 Answer

1993 yj jeep from BC.


Often, one bulb goes out, you don't notice, then when the other goes out, someone finally tells you! Check for power and good ground at lights (don"t forget... someone has to step down on brake or there will be no power there!!) If no power, check fuse and brake light switch. In general wiring does not go bad often enough to be of concern.

Jul 30, 2008 | 1993 Jeep Wrangler

Not finding what you are looking for?
1993 Jeep Wrangler Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

81294 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...