Question about 1994 Pontiac Trans Sport

Open Question

Cnt find pvc valve on 1994 ontiac transport 3800 v6

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

dcramer531
  • 1654 Answers

SOURCE: I need to know how

I can give you instructins on the switch replacement but no diagram, and one will not be needed for this since it is plugged in and can only go one way. You will need a set of torx bits if you don't have these already, they can be purchased at most auto parts and sears and such places. First you have to remove the horn pad from the steering wheel. Take your torx bit with a 3/8 extension and put it on a 3/8 ratchet to remove the forward torx bolts behind the steering wheel. Turn counterclockwise on each bolt until they are removed. Take the horn pad off. Disconnect both terminals on the battery and wait at least two minutes before proceeding to remove the airbag. This is a safety precaution that will prevent the airbag from accidentally deploying. Unplug and remove the airbag. Unplug the electrical connector by pulling it apart using your hand.Remove the steering wheel. Remove the steering wheel nut retainer using a pair of pliers. Take your deep 13 mm socket with your ratchet and turn counterclockwise to remove the nut. Install the steering wheel puller by inserting the three screws into the holes on your steering wheel. Put the ratchet with your 13 mm socket on the middle screw and turn clockwise until the steering wheel is removed.Remove the plate cover. Press down on the shaft plate cover and remove the retaining clip using the pliers. Take the plate cover off.Remove the canceling cam and spring. Lift up on the canceling cam to remove it. Take the spring out.Remove the hazard flashing button. Remove the retaining screw in the middle of the button using a Philips screwdriver.Remove the turn signal switch. Remove the three screws from the turn signal switch. Pull the turn signal switch out through the steering column and unplug the electrical connector. Installation is reverse of removal.
Here is a link to a visual instruction guide although not excactly the same vehichle as yours but is very similar, it also has some questions that need answered before you replace the switch, like diagnosing if it is the switch or the canceling spring or cam.
tss.likeabigdog.com

Posted on May 13, 2011

jturcotte
  • 7716 Answers

SOURCE: beit routing for a 1994

thanks for using FixYa.

jturcotte_608.jpg

Posted on Sep 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2012 suzuki sx4 sport back i need to change the pvc vavle but cnt locate the valv on the intake.


I'm not a great fan of suzuki's. Blue is oil burning. If it does this at start up and goes away shortly, Bad valve seals. If it doesn't go away. Really bad seals and valve guides(head job) or the piston rings are already shot. Has it been run low on oil?

Jan 21, 2015 | Suzuki SX4 Cars & Trucks

1 Answer

Pvc value


Valve Cover on 95 % of any vehicle ever made
since around 1970

Aug 15, 2014 | Cars & Trucks

1 Answer

HAVE A 94 PONTIAC TRANSPORT SE 3800 CRANKS BUT WONT START


check for spark and fuel at fuel pressure valve

Oct 07, 2013 | 1994 Pontiac Trans Sport

1 Answer

1994 buick lesabre 3.8 camshaft sensor location


On the 3800 V6, the camshaft position sensor is located behind the water pump pulley. if you were to look at pulley straight on, it is at about the 9 o"clock position. good-day!

Aug 22, 2011 | 1994 Buick LeSabre

1 Answer

Where is the PVC valve 3800 engine


Where is the PVC valve? Standing in Front of the car it is on the left side of the air plenum. Unscrew the oil filler tube and remove the plastic engine cover. There is a sensor on the left side of the plenum. This sensor senses when the PVC valve is open/closed. Don't bother disconnecting the connector or the piece the connector plugs into. Simply twist the whole plastic assembly clockwise = yes clockwise while pressing downward to release the assembly. There is a spring underneath so don't let it pop up. With the assembly out of the way grab the PVC valve with a pair of needle nose pliers, wriggle the valve out. If the o-ring is ok put it on the new PVC valve. Drop the valve in place making sure it seats on the o-ring. Look at the bottom of the assembly to see how the slots line up with the tabs. Slip the slots down over the tabs compressing the spring and twist counter-clockwise. Replace the plastic engine cover, Done!

Oct 13, 2009 | 2000 Buick LeSabre

1 Answer

Engine change


Drop cradle with engine, tranny, steering rack, front struts and all attached to it.

May 10, 2009 | 1994 Pontiac Trans Sport

Not finding what you are looking for?
1994 Pontiac Trans Sport Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...