Question about Oldsmobile Cutlass Ciera

1 Answer

The MAF sensor was replaced and problem continued. Tried a new sensor and problem continues. The computer checks out ok so I need to know how to replace the wire from the MAF to the computer.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 520 Answers

If your sure that the MAS wires are the problem Then the only way to replace them is by tracing them back through the wiring harness and clipping them. Tie new wires to the pigtail where the old wires where cut and reconnecting the MAS. Be sure that the connections are good and do not change the resistance. I will also add that the wires are usually not the problem. The problems that the MAS cause can also be caused by other sensors or tune up issues. I would recommend looking further in to this before going through so much trouble if this may not be the problem. Good luck. This one is going to be a head scratchier.

Posted on Jun 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code P1121 for TP sensor - where is it located on engine of 2002 4.0 ford ranger


P1121 - Throttle Position (TP) Sensor Inconsistent with MAF Sensor The PCM monitors a vehicle operation rationality check by comparing sensed throttle position to mass air flow readings. If during key ON engine running self-test the comparison of the TP sensor and MAF sensor readings are not consistent with calibrated load values, the test fails and a diagnostic trouble code is stored in continuous memory.
  • Air leak between MAF sensor and throttle body
  • TP sensor not seated properly
  • Damaged TP sensor
  • Damaged MAF sensor
Drive vehicle and exercise throttle and TP sensor in all gears. A TP PID (TP V PID) less than 4.82 % (0.24 volt) with a LOAD PID greater than 55% or a TP V PID greater than 49.05% (2.44 volts) with a LOAD PID less than 30% indicates a hard fault.
Do you know what scan data on a scan tool is ?
How to Install Replace Throttle Position Sensor TPS 2001 Ford Ranger Buy...

Jun 21, 2017 | Ford Cars & Trucks

1 Answer

Engine stalling at while in neutral


Lets take one thing at a time.
The squeal could be a slipping alternator belt. The alternator pulls hard on the belt when you first start the engine.
The EVAP sensor problem should not affect performance, just emissions.
The MAF code could be from a leak in the intake hose or air filter, or a wiring problem, instead of a faulty sensor. The sensor is telling the computer there is very little air flowing into the intake.
The miss-fire codes could be another ignition problem such as a coil or dist cap, or fuel problems such as injectors or low fuel pressure.
At this point you could take it back to the shop that replaced the MAF and have them recheck the car, or try a new shop.
If you pay a shop to diagnose a problem and their recommendation fails to fix the problem, they are on the hook to find the actual problem for free. If you tell them what to replace, its on your dime.

Dec 14, 2012 | Cars & Trucks

1 Answer

I have a 2003 suburban that was working fine until today. I drove it to the store with no problem then upon leaving I started it and it was very rough at idle. when I put it in gear it died. I continued...


Find out why the check engine light is on. The first couple of things that pop into my mind is low fuel pressure or a bad or dirty MAF sensor. You will need a fuel pressure gauge to check fuel pressure. I can get you the spec if you need it. You can also try unplugging the MAF sensor and see if it will start/idle. If it does take it for w drive. If performance is improved check the MAF to see if it is dirty. It can be cleaned with MAF sensor cleaner available at your local auto parts store.

Aug 16, 2011 | 1998 Chevrolet K1500

1 Answer

2001 Mazda MPV, 2.5L eng. During accelerating on to highway, van lost power. Van continued to operate but with little power available. I have no engine light and my code "checker" shows PASS (no...


looks like not enough fuel pressure, check the fuel filter.
and the fuel pump pressure.with car running 60 psi
the pump is located at the rear seat driver side you have to remove the carpet to access the cover. if the fuel pressure checked "OK" suspect defective maf sensor (sometimes defective maf sensor do not show errors codes)another way to test is disconecting the maf sensor and start the car (computer goes to limp in mode) and works little better,or check by scanner idle= low grams per seconds and increase when accelerate.

May 02, 2017 | 2001 Mazda MPV

1 Answer

P0102 maf or vaf A low circiut input is the code what are the possible solutions I have recently replaced the fuel pump, fuel filter and air filter. When i start the van refs high if i slightly push on the...


You have also tried replacing the Mass air flow sensor. How does it run with it unplugged? You can also get all your symptoms and the MAF code from a plugged catalytic converter.

Jul 13, 2010 | 2001 Pontiac Montana

2 Answers

Changed maf on 04 verona computer is still saying


Check the computer. Puter may not be receiving the signal from the MAF. Check all grounds and B+ wires for continuity. Use shop Manual for furter detail testing and remember always wear a static guard band of some type when working on ECU aka computer.

Mar 24, 2010 | Suzuki Verona Cars & Trucks

1 Answer

My 2001 Lesabre indicates the gas cap is loose, it has been replaced but it continually flashes, how do I reset it.


You may need to check your MAP sensor. It's a small electronic connector that sits on top of your PCV housing cover. The MAF sensor may need checked as well. The MAF is an electronic sensor at your throttle housing. A diagnostic test will let you know which sensor is defective. These sensors tend to be rather expensive so have a test conducted forst.

Nov 16, 2009 | 2001 Buick LeSabre

2 Answers

2001 sentra, MAF continually goes bad, reads p100, replaced three times, is it the computer or something else?


hy mon ami. i own one of those. and your trouble is the MAF. mine is the sentra 2001 2.0 "se sl 1" and i've tried wiht 4 MAF's. the thing is tath u need tath MAF specfically if u tried whit a maf for the 1.8 doesn't gonna work. at least, here in M?xico they just sold this car one year, taht's wy there's not too MAF's for this model. here is about 11000 pesos (like 900 bucks)

May 31, 2009 | 2001 Nissan Sentra

1 Answer

Check engine light


have you checked the MAP sensor? located rear engine area, center upper firewall, see if vacuum line is attached or leaking, I believe your local autozone can test it to determine whether or not it is good, running rich is a good sign that you have a problem with it or vacuum supplied to it, let me know

May 25, 2009 | 1995 Ford F150 Styleside Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...