Question about 2001 Chevrolet Silverado 2500

Open Question

Chevy truck anti theft system reset

Anti theft system is activated

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: Chevy Tahoe 2004 Anti Theft Device has been activated.

leave the key on for about 5 to10 min then try to start. Are reset to computer by leaving the key on for 10 min and try to start the vehical.Do this procese 3 time then it shold reset

Posted on Feb 12, 2009

Ad
csmock132
  • 4669 Answers

SOURCE: how do i reset anti theft system 97 chevy

Leave the key on for 11 minutes until the security light stops blinking.

Posted on May 18, 2009

sheakcoleman
  • 2 Answers

SOURCE: car wont start anti theft device activated on chev. equinox 2006

alarm remote needs new batterys

Posted on May 27, 2009

  • 206 Answers

SOURCE: 2003 chevy malibu won't start and seems to be with the fuel pump

Try this I got it from the emission wiz
Put your key in turn it on dont start wait 10 mins remove key wait 10 seconds repeat this a total of 3 times. If that dont work try a different key do the same thing. This relearns your key to the ignition it started with Gm cars and trucks from 1999 to to 2006. It is a big problem but there is no recall that I know of. If that dont work a dealer needs to probably replace and reprogram your ignition switch and keys

Posted on Jun 01, 2009

Molson02536
  • 3854 Answers

SOURCE: 1999 1500 Chevy Silverado - microchip for anti-theft?

Document ID# 803013
1999 Chevrolet Chevy K Silverado - 4WD

Security Lamp Illuminated on the IP, Engine Stalls, No Start, DTC B2960 (Security System Sensor Data Incorrect but Valid) Set (Inspect and Repair Cause of DTC B2960)
1999-2001 Chevrolet and GMC C/K Pickup and Utility Models (Silverado, Sierra, Tahoe, Suburban, Yukon, Yukon XL)

This bulletin is being revised to add information on inspecting for electrical intermittent conditions and important connector C201 tightening steps. Please discard Corporate Bulletin Number 01-08-56-002 (Section 08 -- Body and Accessories).

Condition
Some customers may comment on the following conditions. These symptoms may be intermittent.

• Security lamp illuminates while driving. The Security lamp may be On or Off when the customer brings the vehicle to the service facility.

• The engine cranks but will not start and the Security lamp is flashing.

• The engine starts then stalls and the Security lamp is flashing.

Cause
Condition(s) may be due to an incorrect Passlock™ sensor voltage received by the body control module (BCM) from the Passlock™ sensor due to the following conditions. Most intermittent conditions are caused by faulty electrical connections or wiring.

• A 7 ohm variation in the sensor ground circuit wiring, circuit 1057

• A 100 ohm variation in the Passlock™ sensor signal wiring circuit, circuit 1836

Inspect for the following items:

• Broken wiring inside the insulation.

• A poor connection between the male and female terminal at the connector. Refer to Testing for Proper Terminal Contact under Testing for Intermittent and Poor Connections in Wiring Systems for the specific procedure.

• A poor terminal to wire connection. Some conditions that fall under this description include poor crimps, poor solder joints, crimping over the wire insulation instead of the wire itself, and corrosion in the wire to terminal contact area.

• Wire insulation that is rubbed through. This causes an intermittent short as the bare area touches other wiring or parts of the vehicle.

• A poor connection between the male and female terminal at a connector. This poor connection may be the result of contamination or deformation.

- Contamination may be caused by the connector halves being improperly connected. A missing or damaged connector seal, damage to the connector itself, or exposing the terminals to moisture and dirt can also cause contamination. Contamination, usually in the underhood or underbody connectors, leads to terminal corrosion, causing an open circuit or intermittently open circuit.

• Separate the connector halves.

• Visually inspect the connector halves for contamination. Contamination may result in a white or green build-up within the connector body or between terminals. This causes high terminal resistance, intermittent contact, or an open circuit. An underhood or underbody connector that shows signs of contamination should be replaced in its entirety including the terminals, the seals, and the connector body.

- Deformation is caused by probing the mating side of a connector terminal without the proper adapter, improperly joining the connector halves, or repeatedly separating and joining the connector halves. Deformation, usually to the female terminal connector tang, can result in poor terminal contact causing an open or intermittently open circuit. Using an equivalent male terminal from the J 38125-B, test that the retention force is significantly different between an good terminal and a suspect terminal. Replace the female terminal in question.

Correction
Have any of the following components had service recently?

• The BCM

• The ignition lock cylinder case assembly

• The PCM/VCM

If any of the above components have been replaced, the Programming Theft Deterrent System Components procedure must be performed before any diagnostic procedures are performed.

To assist in diagnosis, the following steps are provided.

Does the engine start? If not, use the Engine Cranks but Does Not Run diagnostic information in the Engine Controls sub-section of the applicable Service Manual.
Important:

• The Security telltale on the message center is controlled by the vehicle theft deterrent (VTD) system and the content theft deterrent (CTD) system. The Security telltale is controlled by the BCM through the Class 2 data line.

• The VTD system portion of the BCM controls the Security telltale when the ignition switch is in the On position. The VTD system uses the Security telltale as a malfunction indicator.

• The CTD system portion of the BCM controls the Security telltale when the ignition switch is in the Off position. The CTD system uses the Security telltale to identify system status.


Observe the Security indicator lamp in the instrument panel.
Remove the key from the lock cylinder.
- Security indicator should be Flashing when the door is open.

- Security indicator should be Off when all the doors are closed.

- If the Security indicator does not come On or go Off correctly, refer to the Content Theft Deterrent System diagnostic and repair information in the applicable Service Manual.

With the Doors closed, place the key in the lock cylinder and turn to the Run position. Observe the Security indicator lamp.
- Lamp is On and does not go Off however, the engine starts. This indicates that the VTD system detected a fault when the engine was running.

- Lamp flashes On and Off. This indicates a problem has been detected by the VTD (Passlock™) system and the engine may not start this key cycle, a current condition.

Important: You must diagnose the diagnostic trouble codes (DTCs) in the order specified in the DTC table shown below. Failure to do so may result in one or more of the following conditions:


• Extended diagnostic time

• Incorrect diagnosis

• Incorrect parts replacement


DTC
Diagnostic Procedure
Module

Important: Before you use this table, diagnose P0601, P0602, P0604, and P0606. Refer to Diagnostic System Check - Theft Deterrent.

PXXXX Other PCM DTCs

Refer to the following procedures:

• Diagnostic System Check - Engine Controls in Engine Controls - 4.3L

• Diagnostic System Check - Engine Controls in Engine Controls - 4.8L, 5.3L, 6.0

• DTC P0192 in Engine Controls - 6.6L

• Diagnostic System Check - Engine Controls in Engine Controls - 8.1L


If none of the above items are true, proceed with the following steps:

Install seat covers.
Connect the scan tool to the diagnostic link connector (DLC).
Enter scan tool diagnostics.
Select the model year of the vehicle.
Select light truck.
Select F1, (Body).
Select "C" or "K" for Series.
Select F0, Body Control Module.
Select F0, (Diagnostic Trouble Codes (DTC)).
Select F0, (DTC information).
Select F0, (Current DTC).
Record on the repair order any current DTCs displayed. If none, skip the next step.
Is a current B2960 DTC displayed? If no, the condition is not present with this key cycle. Continue to the next step.
Select Exit.
Select F1, (History DTC).
Are any history DTCs other than B2960 present? If so, diagnose those DTCs first using the appropriate service information, otherwise continue.
Select Exit.
Select Exit.
Select F1, Data Display.
Select F6, Security.
Cycle the key to the OFF position and wait 20 seconds.
Slowly turn the key to the RUN position. Be careful not to turn the key into the START position.
Observe the following values:
- Passlock™ Data Voltage should be 5.0 volts.

- Passlock™ State should be Normal.

- Passlock™ Code should be Open.

Rotate the key to the START position, and observe the following again:
- Passlock™ Data Voltage should be less than 5.0 volts. Passlock™ Data Voltage should remain steady and not fluctuate. The test vehicle used for this diagnostic procedure had a voltage value of 2.49 volts. The vehicle being worked on may be either higher or lower than this value. The key is that it has to be less than 5.0 volts.

- Passlock™ State should be "Monitor Passlock™".

- Passlock™ Code should be Valid Code.

If no trouble is found and the customer has experienced one of the symptoms or the code is a history DTC, the most likely cause is the VTD (Passlock™) wiring, specifically the wires from the VTD (Passlock™) sensor to the BCM.

Posted on May 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2005 Chevy Colorado anti theft My truck shows the anti theft light on and it will not crank, how do I reset the computer?


There is no magical reset procedure , you have it scanned for DTC'S -diagnostic trouble codes ! Then tested and repaired . Which means you have to take your vehicle to a qualified repair shop .

Dec 15, 2016 | 2005 Chevrolet Colorado

1 Answer

Why do my my 04 jeep cherokee runs for 3 seconds then shuts off?


sounds like the anti theft system is activated , proberly cuts the power to the fuel or ignition follow this link for reset procedure
How to Reset the Anti Theft on Jeep Cherokee eHow

Jul 15, 2014 | 2004 Jeep Grand Cherokee

1 Answer

2003 ford ranger theft light blinking and won't start


the anti-theft has been activated and needs to be reset.you may have to get it to a shop that has the tools to do this or go to the dealer to get it done.did you use a key that was cut as a spare and doesn`t have a chip in it.this usually can cause this.also if the wires at the switch break it can activate the anti-theft system.

Feb 09, 2012 | Mercury Tracer Cars & Trucks

1 Answer

2002 chevy malibu wont start i think it is the anti theft system.


If this is so then it is defeating OFF the power to the ignition system. Check the power to the ignition system or check to reset the theft alarm if this was activated. Using the keyless remote and the ignition key into the holder reset the qalarm if this has tripped with a false entry.
If not check the fuel and ignition for the failure of command from the ECM.

Dec 03, 2010 | Chevrolet Malibu Cars & Trucks

1 Answer

Why would a 2003 Chevy Impala's speakers not work? The radio and CD player work, but I get no sound what so ever. The car was bought used in 2009 and the radio has never worked. I was told that something...


This may be a anti-theft issue. If it is and you want it fixed, the Chevy Dealter is probably the best place to have this work done, IF it can be done at all. My Chevy radio instructions tell me that if there is a genuine power loss to the radio when the anti theft system is activated (like someone breaking into the car and stealing it, cutting the wires) that the radio will not work again with out GM intervention.

Mar 24, 2010 | 2003 Chevrolet Impala

1 Answer

My 2003 Saturn Ion will not start. I had it towed to our regular mechanic, he tested it and says everything is fine with the car. He mentioned that the anti-theft system has been activated and can not...


There are no saturn dealers any more . Take it to Chevy , buick , or cadillac dealer .
can not reset the computer. ?????? There is no reset for ant-theft system . Is the security light on ? Have codes read ,fixing the problem will turn off the light an reset the system .

Sep 01, 2017 | 2003 Saturn ION

2 Answers

99 chevy cavalier theft system light on steady, car wont crank.


My 2000 cavalier has done this for 6 months. You take your key out then open your door, wait ten minutes and the system resets itself and the car will start-annoying you bet!!!

Jul 20, 2009 | Chevrolet Monte Carlo Cars & Trucks

1 Answer

1992 chevy corvettecranks but doe's not start.fuel pump not working but good.fuse good doe's not have power to fuse at all.


The built in factory anti-theft system disables the fuel pump if it is triggered, or this can be caused by a fault in the anti-theft, those are a few of the reasons, arm and dis-arm anti-theft is it working properly? Follow this procedure to check security system:

The Security System is reset by unlocking the driver's door twice with the Ignition Key, but if it does not reset, most likely the Ignition Lock Cylinder has failed. It has small contacts which 'sense' the pellet on the key and transmits that data to the Anti-theft Module. Often the contacts, or the micro wires, break causing the module to think you have no key in there. The ASR may be illuminating since the Security System is active, trouble codes?

Aug 04, 2008 | Chevrolet Corvette Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...