Question about 2002 GMC Safari

Open Question

02 gmc safari front brakes

Remove and repair

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
leetamara
  • 702 Answers

SOURCE: 1994 GMC Suburban front hub / bearing removal

Knock the wheel studs through the assy.

Posted on Jun 09, 2008

Ad
clarktravis8
  • 74 Answers

SOURCE: 2000 GMC Safari anti-lock brakes

There was actually a recall for this. Go to your local GMdealer and have them check your VIN for a recall. If not under recall get out of there its easy to repair yourself don't let'em fool you.Remove the front pads caliper and rotors. Locate the abs sensor mounted to the wheelbearing assembly by a small socket head cap screw (Allen wrench). Removethe bolt and softly gently/wiggle the abs sensor around until it pops upout of the hole. some will break, which is why it wouldbe nice if the recall applies to your vehicle that way if they break gm replaces. Once you get both sides removed, clean themounting surface of all rust or build up with w-d 40 and small steel toothbrush then wipe off excess with clean rag and mild soap and warm water, dry completely make sure no spray residue exist on parts, Next apply a thin layer of lubricant grease to preventfuture rusting and reassemble.The rust build up under the sensor is causing the angle to change resultingin inaccurate wheel speed readings in the abs module your abs module will interprets this asa wheel is either slipping or skidding and applies your abs. This should make you happy with no more irritations. Please rate me. If you need further assistance you can always ask me. Good luck with this.

Posted on Apr 25, 2009

aaangie220
  • 202 Answers

SOURCE: 1999 GMC Safari brakes grab mostly in sudden stop

try having the rear drums resurfaced. and clean and deadjust the rears a bit. the rears are doing the grabbing

Posted on Aug 04, 2009

  • 811 Answers

SOURCE: 2004 GMC safari rear electric door lock is not working

remove panel, if any, check for loose wires, clean and lubicate 

Posted on Sep 13, 2009

Boole5555
  • 160 Answers

SOURCE: how to check transmission fluid on a 02 gmc safari

You need to warm up the engine, pull out the dipstick, wipe it off and reinsert. Pull it out once again and look to make sure the fluid level is sitting between the marked areas on the dipstick.

Posted on Jan 08, 2010

Testimonial: "thank you"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

03 gmc safari leaking brake fluid around radiator


If you don't know something or work on
your own vehicles, then you need a repair shop

Mar 21, 2013 | 2003 GMC Safari

1 Answer

Knocking sound in 1995 GMC Safari


if its an all wheel drive model it may be a cv axle in front-end

Oct 20, 2012 | 1995 GMC Safari

1 Answer

Need to replace brakes on 2000 GMC Safari. does it have disc brakes all around or drum rakse in rear?


Disc brakes in the front and drum brakes in the rear. Make sure that you repack the front bearing's with wheel grease before finishing the job.If the front rotors and or the rear drums have a rough brake pad surface,get them resurfaced before installing new brake pads or brake shoes in the rear. you can go online or your public library for complete instructions on how to replace the brakes on that vehicle.

Apr 01, 2011 | 2000 GMC Safari

2 Answers

I have a 1993 GMC Safari that started making a strange noise from the front end I have taken it to 2 mechanics they both tell me that the problem is the wheel bearing. 1 says the bearing is in a sealed...


I just re-packed the front end bearings. Haynes covers the brakes real well, but not the bearings. Each front wheel has two bearings (one inside the wheel). So you have to remove the wheels, brakes, dust cap, grease seal and brake rotor to access the bearings. .
Expect to replace the grease seal because the rubber will be brittle or hard. Clean and inspect the bearings and races real well. If the bearings are squealing expect to replace some of them also.
Replacing the brakes so the pads stay in place is the trickiest part.

Jan 08, 2011 | 1993 GMC Safari

1 Answer

Where to find free break squematic for GMC safary


The rear of the resivoir is for the front brakes. Look for moisture behind the tires if you press the brakes while still. you either blew a line or a caliper has blown

Feb 24, 2010 | 2000 GMC Safari

1 Answer

Front wheel bearing 2000 GMC Safari


Yes is fairly easy job because the wheel bearing comes off whit the brake rotor just remove the brake caliper the rotor center cap the safety ping and the center nut on the brake rotor the hole thing will come off but "NOTE" you are going to need a new brake rotor because if the bearing was bad probably the rotor is bad to a new grease retainer seal and of course plenty of grease. Good luck :)

May 30, 2009 | 2000 GMC Safari

2 Answers

2000 GMC Safari anti-lock brakes


There was actually a recall for this. Go to your local GMdealer and have them check your VIN for a recall. If not under recall get out of there its easy to repair yourself don't let'em fool you.Remove the front pads caliper and rotors. Locate the abs sensor mounted to the wheelbearing assembly by a small socket head cap screw (Allen wrench). Removethe bolt and softly gently/wiggle the abs sensor around until it pops upout of the hole. some will break, which is why it wouldbe nice if the recall applies to your vehicle that way if they break gm replaces. Once you get both sides removed, clean themounting surface of all rust or build up with w-d 40 and small steel toothbrush then wipe off excess with clean rag and mild soap and warm water, dry completely make sure no spray residue exist on parts, Next apply a thin layer of lubricant grease to preventfuture rusting and reassemble.The rust build up under the sensor is causing the angle to change resultingin inaccurate wheel speed readings in the abs module your abs module will interprets this asa wheel is either slipping or skidding and applies your abs. This should make you happy with no more irritations. Please rate me. If you need further assistance you can always ask me. Good luck with this.

Apr 25, 2009 | 2000 GMC Safari

Not finding what you are looking for?
2002 GMC Safari Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...