Question about 1998 Toyota Land Cruiser

Open Question

How to clear ABS light on 1998 land cruiser - 1998 Toyota Land Cruiser

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 330 Answers

SOURCE: Toyota Land cruiser ABS Failure

What kind brake fluid you use, the best way is to get dealer O ring and use dealer's brake fluid. some brake fluid damaged the rubber.

Posted on Jul 26, 2008

  • 109 Answers

SOURCE: toyota land cruiser unknown warning light

Try calling these guys and see if they can help.
(818) 882-1238

Posted on Mar 29, 2009

  • 209 Answers

SOURCE: 2000 Land Cruiser Parking Brake alarm will not turn off.

check the parking brake switch if it is engaging and disengaging when you pull the the parking brake.

Posted on Apr 29, 2009

  • 636 Answers

SOURCE: i need back door hinges for toyota land cruiser

Look at an auto wreckers near you , they should have lots for cheap.

Posted on Jul 28, 2009

  • 507 Answers

SOURCE: 2004 toyota land cruiser airbag light is on

You may have upset the sensor on the chassis rail which has set off the light,it can take a while to set off ,the damage is minimal and the sensor is slow to crack internally or fail,you can try to disconnect the battery for 1 hour or so but no guarantees on that but even so it can work ,if the light comes back on you may need to see a dealer ,check at the front of the rails under hood for damage of any kind

Posted on Nov 28, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How i can fix abs land cruiser 2008

-Why you know ABS is not working...?
-ABS is working ONLY when you Stop suddenly. And your foot
MUST hole Still.
-Here how you test your ABS. It's still working or no:
*Make sure NOT On Street! Drive the car about 20 mile per hour and then immediately brake (Full Brake. Do not release your foot. If you feel like the brake lock and unlock the wheel but very fast. This mean Your abs is working fine.)
Even the ABS is not working the regular brake still work.
Don't worry about.

Good Luck.

Mai Lor

Apr 26, 2015 | 2008 Toyota Land Cruiser

1 Answer

We now have no brakes after ABS light & buzzer came on how do we fix

first check and clean ABS sensors for proper contact. restrictions give's you ABS light indicator's on. and possibly solve brake failure.

Nov 24, 2012 | 2006 Toyota Land Cruiser

2 Answers

Can you help with tappet settings for 1fzfe toyota land cruiser thanks keith

Hi.If you follow this link you can download a free manul for your auto that should tell you the specs.It takes a little while to download but should be worth it!Hope this helps. - 13k

Apr 17, 2010 | 1998 Toyota Land Cruiser

1 Answer

Do you have to remove the inside panel of the back door to replace the liceince plate light ?on a 1998 land cruiser.

panels are normally just pushed in on clip if there is no visible screws just put screwdriver and see will panel pop of clips do it carefully

Mar 31, 2010 | 1998 Toyota Land Cruiser

1 Answer

Abs alarm will not stop

Have you removed air from the ABS Punp that can cause the alarm to activate.

Nov 18, 2009 | 1998 Toyota Land Cruiser

1 Answer

2008 Land Cruiser brake noise

I believe what your hearing is your ABS system working .. its probably one of those that is just a little louder than it should be. drive it a while and see if it works out .. if not take it back and tell them the ABS is loud and see what they say.. thanks Jerry

Apr 26, 2009 | 2008 Toyota Land Cruiser

1 Answer

Differetial locks for 94 land cruiser

91-97 Land Cruisers had a factory option for front and rear locking differentials. This is a seperate switch and is usually located to the left of US model Land Cruisers. The center dash button locks your transfer case differential changing your Land Cruiser from all wheel drive to four wheel drive depending if you have ABS or not this button either says ECT or Center Dif Lock. If you do not have the Front/Rear locking differential option then your Land Cruiser has open Front and Rear. Hope this answers your question.

Jan 19, 2009 | 1994 Toyota Land Cruiser

1 Answer

Toyota Land cruiser ABS Failure

What kind brake fluid you use, the best way is to get dealer O ring and use dealer's brake fluid. some brake fluid damaged the rubber.

Jul 26, 2008 | 1999 Toyota Land Cruiser

1 Answer

Problem on abs sistem im jorge from Mozambique im a mechanic ive a got a toyota land-cruizer uzj100 my brake master cylinder had a air leak when i press brake pedal the abs light come on and brakes get...

you need a brake booster as far as abs light you need to to put tester on system and find out what code it has in it before i can diag you have to seprate prolbems

Jun 14, 2008 | 2006 Toyota Land Cruiser

Not finding what you are looking for?
1998 Toyota Land Cruiser Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides