Question about 2006 Dodge Ram 1500

Open Question

DTC B2213 I have a dodge ram im working on. Tach isnt working at all. Came up with code B2213. What is a good diag procedure for this problem

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
co7196
  • 3433 Answers

SOURCE: 2001 Dodge Ram 2500 - gauges don't work

check the engine to body ground strap. located rear top of engine screwed to firewall Remove,clean, and resecure.

Posted on Nov 12, 2009

Ad
  • 736 Answers

SOURCE: My 2003 dodge ram 1500 shows dtc code P0420 can

PO420 code tells you the catalytic converter is not reaching the proper temperature .. that is measured by the back oxygen sensor (just behind the CAT ... make sure the heat shield is in place (in cold weather) .. you can check for a rattle in the cold CAT (thats bad) .. the rear O2 sensor can be bad or you could have a bad catalytic converter or one thats on it way to being bad .. there are some tests a mechanic can do .. 1. a back pressure test 2. measure the temperature of the CAT surface .. it should be around 225 deg F (after warmup) .. a non contact (IR) thermometer is handy for this .. make sure the pipe behind the CAT and the muffler are not leaking ..some "high flow rate " replacement mufflers will cause the trouble ..

Posted on Jul 02, 2010

moparhart
  • 245 Answers

SOURCE: I have the code # po443

check the vacume lines

Posted on Jul 12, 2010

roniecon
  • 6826 Answers

SOURCE: 96 dodge ram 2500 cummings, the tach, cruise,

I would only assume the alternator is the problem,if there is not enough voltage being supplied,the accessories will not work,or work properly.

Posted on Aug 16, 2010

skychief2001
  • 21873 Answers

SOURCE: dodge ram 4.7 engine dtc p0307

Could be a problem with the wiring for the injector or the coil.
Or even the crank sensor.
The computer "sees" the drop in RPM to peg a cylinder for a miss.
Do you think the miss is really there ?

Posted on Aug 19, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2003 dodge intrepid will not shift into third gear. code reader says po 700 and po 888 and transmission sensors have been changed also computer was flashed after used motor put in car


Hi there:
First I suggest complete trans flusing procedure done, and a transmission fluid modifier added at the same time. You might have a sticking valve in the valve body, and the flushing procedure may help that out if true. If not, you may still have a sticking valve in the valve body.

The P0700 code is stored in the ECM and just tell you that there is a code in the TCM (Transmission Controller), that is the P0888.



DTC P0888 is telling you that the Transmission Relay output is always off; in this link can checl the Diag Chart for that code, this coul help...







8_22_2012_9_52_07_pm.gif

Zoom Image link HERE

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 22, 2012 | 2003 Dodge Intrepid

1 Answer

2007 Dodge Ram 2500, Took it in to the Dodge Dealership for a diagnostic this is what it said Engine light is on and the abs and brake lights. Also the Speed odometer is not working. Diagnose only...


Check all the "spare" fuses in the fusebox. replace any that are empty with the proper grade fuse. If it pushes in like it's connecting, that may very well be your problem. If it just slides in and out, the slot is unused, and therefore, "spare".

Jan 12, 2011 | 2007 Dodge Ram 2500 Mega Cab Laramie

1 Answer

Error codes


P0523 means the Oil pressure voltage to high. Your Oil pressure sensor may need to be replaced. P1682 means your charging system is to low. Your voltage regulator may be going bad or the whole alternator. p1693 means a Diagnostic trouble code (DTC) has been detected in the ECM or PCM which is related to the above DTC P0XXX codes. Good luck and hope this helps. Keep me posted, be glad to help

Jun 11, 2009 | 1999 Dodge Ram

2 Answers

SPEEDOMETER-TACHOMETER-AIR CONDITIONER ALL WENT OUT AT SAME TIME


2000 dodge ram 2500 truck 4wd the abs light and air bag light were on then the check engine light went on then all of a sudden all the gauges and warning lights went dead and off including the tach and other gauges. But now all the gauges are working and the check engine light went off with all the others and the tach and other gauges are working. what is the problem with this truck ? The only code it read was p1687 from the dtc. Is the problem the pcm or something else.

Jul 31, 2008 | 2000 Dodge Ram 3500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...