Question about 2001 Toyota Sienna

1 Answer

Remove a stuck tie end tod - 2001 Toyota Sienna

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Toyota Master
  • 808 Answers

The tie rod is a tapered fitted once the castle nut is off a pickle fork is beaten into the space between the rod and steering arm and falls out . no pickle fork then look for the raised portion on the steering arm smack it there 3-5 times hard it should fall out if this does not work suggest a 2 jaw pull and press the stud portion out . good luck.

Posted on May 07, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install tie tod ends


Basic task is to take the nut off the top of the joint, and knock the stem out of the knuckle or joint. You may need to use a pickle fork to get it to move.
Then you unscrew the end from the coupler.
Be sure to measure the length of the assembly before you remove it, you may need to have the front end aligned after the procedure.

Jul 14, 2014 | 1978 Chevrolet C1500

1 Answer

Have anyone out there ever change inner tie rods on a1995 honda odyssey?,if so simply explain,THANKS


Procedure on replacing the inner tie rod ends:


1) Raise and safely support the vehicle.

2) Remove the front wheel/tire assembly.

3) Clean the steering rod between the steering boot and outer tie rod end lock nut with a suitable penetrating lubricant and a clean cloth or shop towel.

4) Loosen the outer tie rod end locking nut 1/8 turn.

5) Loosen the steering boot clamp(s), and slide the small clamp off the boot.

6) Carefully loosen the boot and slide outward off the steering rack and onto the shaft to expose the inner steering rod mounting fastener.

7) If necessary, position the inner steering rack shaft in or out to allow for additional access.

8) Relieve the steering rod nut locking tab from the inner steering rack shaft, then loosen the steering rod ball socket nut 1 turn.

9) Matchmark the tie rod end to the threaded shaft.

10) Remove the cotter key and castle nut from the outer tie rod end threaded spindle, and using a tie rod end removal tool, remove the tie rod from the steering knuckle.

11) Hold the tie rod with a wrench, and remove the outer tie rod end from the threaded rod, counting the number of complete turns it takes to remove the tie rod end from the shaft. Write the number of turns on a piece of note paper.

12) Remove the tie rod end lock nut from the threaded steering shaft.

13) Slide the steering rack boot off the shaft.

14) Remove the inner steering rod ball socket nut from the inner steering rack shaft.

To install:

1) Inspect the tie rod end for looseness, and the steering rack boot and tie rod end boot for cracks deterioration or damage and replace as necessary.

2) Clean steering rack shaft and apply a light coating of Genuine Honda Power steering fluid as necessary.

3) Apply a medium strength locking agent to the threads where the inner steering rod ball socket mounts. Use a new locking washer and a new stop washer, and install the inner tie rod onto the steering rack shaft.

4) Tighten the inner tie rod end fastener by 58 ft. lbs. (78 Nm)

5) Peen the lock washer over the nut or onto the flat surface of the steering rack shaft.

6) Apply silicone grease to the outer circumference of the inner tie rod end ball socket, and onto the groove just outside of the socket.

7) Apply silicone grease to the inside of the small end of the steering rack boot, and slide the boot over the steering shaft and onto the rack and install the boot clamps. If the boot has air hose fittings make sure they are installed as removed.

8) Apply a light film of an anti-seize compound onto the threaded tie rod end, and install the tie rod end lock nut.

9) Install the tie rod end onto the tie rod, turning it in exactly the number of turns it took to remove it.

10) Install the tie rod end following the tie rod end installation procedure.

11) The balance of installation is the reverse of the removal procedure.

12) Check the front end alignment and adjust as necessary.

Sep 10, 2012 | 1995 Honda Odyssey

1 Answer

How to replace tie tods on a 2001 and should both tie rods have a grese fighting or just one. and how to get the bands off to remove the boot .


ok, Tie rods don't have boots. The only thing up front with a boot is the CV joint. You have to use a cutter to remove the bands from a CV joint however, unless your trying to repair the joint you don't want to do that. There is no lubrication point inside the boot you need to reach. If for some reason you need to remove that boot you need to get a CV joint Boot Repair kit to do this as it will have replacement bands to use in the repair. Because of the nature of a CV joint and it's importance to operating correctly I don't recommend trying to do a Joint repair on your own. On the Tie Rod typically you will replace the out end. You need to have a tie Rod puller to remove the tie rod end off the "A" frame after you have released the lock nut in the center then simply unscrew the tie rod end. You'll want to make sure you mark the old tie rod somehow so you can put beside the new part and mark it so you know how far to screw that in so the Alignment matches, as close as possible. The tie rod puller is a special tool you can get from Auto Zone to remove the Tie rod end from the "A" frame.

Oct 27, 2010 | 2002 Chrysler PT Cruiser

2 Answers

Need to replace front outer tie rod end. How do you do this? Is it simple replacement? 1989 Ford Festiva


Locate the tie rod end, and remove the nut that hold it in place.

Using a hammer and prybar, lodge the prybar under the tie rod end, and against something else, and pry up gently from underneath, while striking the area of the knuckle that it connects into with appropriate force. The tie rod end will dislodge. There is also a tool for this, if you'd rather use it. It looks like a tuning fork, and is called a "tie rod remover". Its use is self-explanatory. You can rent a kit to do this from AutoZone or Advance, the rental is about $50, IIRC, and you get your money back when you return the tool.

After having done that, loosen the locknut on the back of the tie rod, and count the number of threads that you have to turn the tie rod end to get it off from wherever it's installed. This is VERY important.

Once the old one is off, thread the new one on EXACTLY the same number of turns. This will ensure that your vehicle's alignment is about as close as you can get it without taking it to an alignment shop. Tighten the lock nut, reinstall the joint end into the hub, and torque the retainer nut. If there was a clevis or pin, reinstall it.

Aug 11, 2010 | 1989 Ford Festiva

1 Answer

How to replace tie rod ends


1. Loosen the wheel lug nuts. Raise the front of the vehicle and support it with jack stands.
2. Hold the tie rod end with vice grips or a pipe wrench and loosen the jamb nut (the nut at the inner end of the tie rod).
3. At the other end of the tie rod remove the cotter pin and remove the castle nut.
4. The tie rod end will come out by turning counter clockwise. Before turning it grip the inner tie rod with pliers (the part on the other side of the jamb nut) so that it doesn't turn. Count exactly how many turns it takes to remove the tie rod end.
5. Turn the new tie rod end in exactly the same number of turns that were required to remove the old one. Tighten the jamb nut up against the new part.
6. Re-install the castle nut and replace the cotter pin with a new one.
7. Re-install the wheel and lug nuts. Re-torqe them with the vehicle back on the ground.
8. It is a good idea to replace both tie rod ends at the same time and to get a front end alignment afterwards.
I hope this helps.

Mar 25, 2010 | 1998 Ford Windstar

1 Answer

TYROD


to change a tierod on 2001 malibu, jackup and remove front tire, next locate the nut holding tierod on tire side, remove cotter pin and loosen but do not remove the castle nut from the tie-rod end ball joint stud. then install a small puller and break loose the tie-rod end from the steering knuckle. remove nut and detach tie-rod end. (I forgot to mention before taking tie-rod end off of vehicle,loosen the tie-rod end jam nut and mark the position of the tie-rod end on the threaded portion of the tie-rod. you can also count the number of turns to take off so you can put it back on.) make sure the new tie-rod end is aligned with the mark you made on the threads of the tie-rod. have the alignment checked or adjusted after you have installed tie-rod end. if in doubt you can go to any auto parts store and buy a haynes manual for your vehicle, they are based on a complete vehicle teardown. the cost is only about 20.00.

Nov 23, 2009 | 2001 Chevrolet Malibu

1 Answer

How to remover tierod


You remove the concerned front-wheel.
Jack up the car front and support it on jack-stands.
Remove and tie-up the brake caliper to more expose the tie-rod end.
loosen the jam-nut, then mark the position of the tie-rod end in relation to the threads.
Remove the cotter-pin from the tie-rod nut.
loosen but don't remove the tie-rod end ballstud and disconnect the tie-rod end from the steering knuckle-arm with a puller. OR
With a medium-size hammer, hit the end of the steering-knuckle where the tie-rod was inserted.
Pull out the tie-rod.

Nov 14, 2009 | 1997 Chrysler Concorde

1 Answer

How to install tie rods on a 1993 del sol


Instructions Things You'll Need:
  • Lug nut wrench
  • Jack
  • Jack stands
  • Wrench or pliers
  • Tie rod puller
  • Marker or paint
  • Pen and paper
  • Anti-seize compound
  • Torque wrench
    Remove the Tie Rod End
  1. Step 1 Purchase tie rod ends that are specific to your Honda model and year, for tie rod ends vary from model year to model year. The tie rod ends often come with nuts and cotter pins (glorified bobby pins).
  2. Step 2 Loosen the lug nuts on the front tires, but don't remove them. Jack up your vehicle, then support it securely on jack stands. Remove the tires.
  3. Step 3 Use a wrench or piers to loosen the outer tie rod's locking nut, but do so by only 1/8th of a turn. Mark the tie rod end's position on the threaded portion of the tie rod with paint or a marker.
  4. Step 4 Take out the cotter pin or key and use a wrench or pliers to loosen and remove the castellated nut from the outer tie rod end's spindle.
  5. Step 5 Separate the tie rod and the steering knuckle with a tie rod puller.
  6. Step 6 Grasp the tie rod with a wrench while you screw off the tie rod end. Make sure you keep track of the number of turns it takes to remove it, and write that number down. It'll help you when you install the replacement tie rod end.
    Replace the Tie Rod End
  7. Step 1 Put a coat of anti-seize compound on the threaded portion of the tie rod end, and screw on the lock nut for the tie rod end.
  8. Step 2 Screw on the tie rod end, making sure you do it in the same number of turns as it took to remove the original tie rod end (see Section One, Step 6).
  9. Step 3 Slip the tapered end of the tie rod end into the steering knuckle and tighten the castellated nut to 29 to 35 foot pounds. If your tie rod end doesn't come with a castellated nut, tighten that nut to 32 foot pounds.
  10. Step 4 Install the new cotter pin and tighten the tie rod end's lock nut. Repeat Sections 1 and 2 for the other tie rod end.
  11. Step 5 Reinstall the tires, tighten the lug nuts and get the Honda aligned.

Oct 28, 2009 | 1994 Honda Civic Del Sol

1 Answer

2004 Kia Sedona shakes/vibrates when turning a corner and accelerating from 0-40. Repair shop replaced front left tire because stell belt showing. Stopped for day after repair then started again tod


one check if your wheels are tight 95 ftlbs if mag wheels remove make sure no heavy corrosin arond hub and rim wheel will not seat properly and come loose. 2 check front end if belts are showing check ball joints and tie rides for wear vans are also known
for bad wheel bearings even if you cant hear it at 80km50mph give or take it may have ecssive play
check that front end .otherchecks ps pump and or loose p/s belt

May 28, 2009 | 2004 Kia Sedona

1 Answer

Rack pinions and bushing installement


pretty decent job ahead first jack up car support with jack stands remove front wheels remove nuts on tie rod ends remove tie rod ends from spindles with tie rod end tool or tap with malet were they sit to loosen them hit the spindle area not the tie rod or tie rod threads then dissconnect power steering lines from steering rack also disconect steering linkage to rack there should be 2 main bolts holding assembly to frame remove them should free rack i know that car may have a unique design were u may have to remove inner tie rod ends first if it has those round bushings that always go bad disconect inner tie rod ends behind engine on top of steering rack then remove rack from wheel well replace those inner tie rod bushings u may be able to leave outer tie rod end connected to spindles and u may be able to get to the sterring rack from behind engine good luck

Mar 28, 2009 | 1997 Chrysler Concorde

Not finding what you are looking for?
2001 Toyota Sienna Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...