Question about 2005 Pontiac Sunfire

1 Answer

How to shut off service light

Need to shut off service light to pass emessions test got new gas cover

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Take the - (Negative) battery terminal out, wait for a few seconds and then put it back see if the message is gone.Please be careful not to touch it anywhere else,Always be safe wear eye protection,gloves).

Posted on May 06, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why could my service engine soon light be on?


The service engine light is usually a cover-all light for your emissions control system. Anything that does meet the exact operating parameters of the engine computer turns this light on. Depending on the state you live in, it will also prevent you from passing your emissions test.
Remedy is to have a service station connect the computer to it, wherein it will read the offending code, and tell them what is out of whack and what needs fixing. Could be serious, could just be your gas cap is loose (yes, it measures the vacuum on your tank).
Good luck.

Mar 19, 2015 | Cars & Trucks

1 Answer

Engine light po446 code evac


EVAP
tighten gas cap, reset 446s with scan tool ,
drive .
if comes back you need ,
try a new gas cap, one that is correct. and dont leak.
comes back still?
tank vent leak down test. get it done. if fail find leak.
if pass ,test all EVAP controls. per FSM
factory service manual covers it in find details.
alldata.com , if in hurry. has these facts..

Aug 21, 2014 | 1997 Isuzu Rodeo

1 Answer

What is code PO446 on a 2001 monte carlo ?


that is EVAP failure.
buy a new gas cap and reset the codes. drive,
if comes back,
do a tank vent system leak down test. fails, fix that next
if that passes, test all EVAP valves. end to end.
the FSM covers this
so does ALLDATA.com , log in and read.

Jul 14, 2014 | 2001 Chevrolet Monte Carlo

1 Answer

Pass lock security system


if it just shuts off, try the auto shutoff relay box..it may be loosing connection with the rest of the harness..

Jan 11, 2014 | 2001 Chevrolet Blazer

2 Answers

I got a 84 ford f 150 straight 6 300 manual. I cant get it to pass emission test . I heard that they were notaries for not passing. any good advice thanks.


Well they need to say why it failed ( unburned hydro carbons?) Check engine light on?, Visable smoke? Nitrogen oxide levels too high? If the light is'nt on and the truck runs good make sure the engine is good and warmewd up as you take it to be inspected. If you have to wait in line to be tested rev the engine at a faster than normal isel as you wait. a freash oil chage will also help. new spark plugs and any other overlooked for mileage driven services to up dated. engines that run too cool as the therostaate not leting the motor get hot enough to burn the fuel good. The air filter not being clean. turn the base idel up as high as you can drive it Ok. Maybe with these things followed it'll pass check and adjust the inghtion timing or set a little higher than stock may push this old motor to pass. Go to the test when their real busy and maybe they won't run all the tests and not catch the reson you failed this last time. Adjust the fuel mixture screw on the side of the carb to the smoothest possible idel and then screw it in till it just slows down and then turn the idel screw back up just enough to have it run at the same speed it ran smoothest at and smeel the ezhaust to see if you can smeel fuel if you can the fuel pump may be leaking fuel into the oil and it's showing up on the test.405553745.jpgThe fresh oil change may cover this as you take it to the test right after you change the oil. Ifthe oil smells like gas you know for shure but it might pass anyway if it's clean enough.

Feb 24, 2011 | Ford F-150 Cars & Trucks

1 Answer

THE GAS CAP WAS NOT ON TIGHT HOW DO I GET THE SERVICE ENGINE LIGHT OFF? DO I NEED TO HAVE A MECHANIC RESET IT?


NO. just drive it a few days. the computer will keep testing it, and if it keeps passing the tests, it will turn off the light by itself.

Dec 10, 2010 | 2005 Nissan Xterra

1 Answer

The airbag light stays on my 2002 chevy tahoe. can it be shut off


no it cant .use a glow plug relay to work the airbag light ,so it will pass the annual vehicle mechanical inspection but dont pass this trade secret on .If vehicle taken for test and airbag light seen then its a failure ,Only when its had a new computer and airbags fitted with a certificate from the dealer only will the vehicle pass ,normal cost????2000euros

Nov 14, 2009 | 2007 Chevrolet Tahoe

2 Answers

Question regarding a honda odyssey 1999 check engine light codes.


Ramon
P0420 relates to the catalytic converter. The computer sees little or no improvement in the exhaust before and after going through the converter. Either your oxygen sensors need replacement (3 total) or you need a new catalytic converter.
What is the mileage on the vehicle? Does it run well? Oxygen sensors generally start to fail after 70,000 miles. Catalytic converters usually fail because the engine is runnig rich and the owner ignores that fault for months. This causes the catalytic converter to overheat and fail.

P1456 relates to the evaporative emission system. This system holds the gas fumes in the system so they are not vented to the atmosphere. The most common cause of this code being set is failing to properly tighten the gas cap after refueling. Take the cap off and clean the sealing O-ring. Put it back on and tighten till it clicks 3 times. Make sure you have the correct gray colored gas cap. Clear the code and see if it resets within a few days. If it does, try replacing the gas cap.
Charlie

Jun 26, 2008 | 1999 Honda Odyssey

Not finding what you are looking for?
2005 Pontiac Sunfire Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...