Question about Cars & Trucks
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
you need a 6 inch extension, short 3/8 ratchet, 5/8 plug socket, 3/8 swivel "u" joint, (sold at sears) 8mm 1/4 drive socket deep well and 1/4 inch ratchet.
find the coil packs (6 total, three in each head.)
remove the two retaining nuts holding each coil pack using 1/4 8mm socket and ratchet.
twist the pack to break the sticking boot below.
pull up (be careful to not rip the boots however it may still happen but rare.)
remove coil packs, the rear is a little more difficult with the intake.
use 6" extension and u joint and ratchet to remove plugs and replace.
reverse order to assemble. Good luck, and hoped this helped.
Posted on Jan 04, 2009
This starter can be changed without disassembling the top of the engine on the 2.5 with automatic transmission. You will need a 10mm, 14 mm, 17mm, and a 9mm wrench. First with any electrical repair disconnect the battery at the negative terminal. The starter is on the driver's side close to the firewall below the intake manifold. Remove the transmission dip stick so you don't ruin it, then look and study the starter itself. You will notice the starter drive housing with a top and bottom bolt. The top bolt is a 14mm and the bottom a 17mm, loosen both a half turn. Remove the top 14mm bolt first, then the bottom 17mm, this will allow you to pull the starter out of the bell housing. With some angling and no brackets holding the back of the starter you should be able to pull it out enough to disconnect the positive wire and 9mm nut from the soleniod. Disconnect the starter ignition small wire by pulling it off it's connector. Now just pull it out of the engine and fender void and you've got it, saving about a hundred and fifty dollars of labor. Take it to the parts house and match it up with a well made remanufactured or new starter. Reverse the proceedure, hook up the battery.
Posted on Mar 19, 2009
SOURCE: Code P0505 on 1999 Acura TL
this code make reference to low idle engine,maybe the throttle body is dirty , air filter clogged, vacumm leak , pcv valve clogged, check for thoses
Posted on Apr 25, 2009
You must contact the parts department of your local Acura dealer to get this code. You will need to show them your car's registration to prove that you are the owner. You may be able to get the code with only the registration and the VIN code (found on the registration). Some manufacturers require the serial number on the radio, which would require that the radio be removed from the car to see the serial number.
Posted on Jun 16, 2009
Tips for a great answer:
Oct 17, 2012 | 2000 Acura TL
Sep 19, 2012 | 1997 Acura TL Series
Jun 27, 2012 | 1999 Acura TL
Mar 27, 2012 | 2000 Acura TL
Sep 04, 2017 | 2000 Acura TL
Apr 30, 2010 | 2000 Acura TL
Dec 31, 2009 | 2000 Acura TL
Oct 29, 2009 | Acura Integra Cars & Trucks
Oct 06, 2009 | 2000 Acura TL
Aug 30, 2009 | 2000 Acura TL
Nov 23, 2017 | Smart Cars & Trucks
63 people viewed this question
Usually answered in minutes!