Question about Cars & Trucks

1 Answer

87 Subaru right rear lower trailing arm bearing removal

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 50 Answers

Need to press new bearing in, locate a shop with a good 6 ton press.

Posted on Jun 30, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
280zlvr
  • 126 Answers

SOURCE: Ford Escape Trailing Arm

hi there this is a problem with all shocks and swing arms where the bolt goes through a rubber bushing and the water and road salt debris gets into bushing and freezes up causing the bolt to stick into bushing use a prybar to dislodge bushing from the area where its been clamped into it will come out

Posted on Jul 19, 2008

  • 75 Answers

SOURCE: trailing arm troubles

Honda has a wonderful way of making so that you need to but the parts new, They don't want you to swap them. This is how they make their money, By making our live difficult.

Posted on Jul 23, 2009

  • 119 Answers

SOURCE: Procedure for replacing rear wheel bearings 2000 Forester

i'm assuming you don't have a hubshark,this is a tool that will alllow you to remove the bearing while the knuckle is attached to the car,you may be able to rent this tool at a auto prts store .if not you need to remove the entie knuckle,first remove the trailing arm bolt,then the lateral link bolt{long and stubborn bolt},disassemble the brake shoes and parking brake cable,abs sensor if equipped the knuckle to strut bolt{no marking necessary they are not eccentric} then you need a to use or borrow a press to remove hub and bearings good luck

Posted on Jul 26, 2009

  • 2 Answers

SOURCE: 2004 Chevy Aveo has clunking noise comming from

bushings available on ebay used them on my 2004 aveo and the work

Posted on Nov 23, 2010

dttech
  • 4803 Answers

SOURCE: Want to know the relationship

The recall for your vehicle may or may not have included replacement of the trailing arm. The recall says that the trailing arm is to be "inspected" then it will be replaced, or modified at the discresion of the person performing the inspection. If it was "replaced", it would require the control arms to be disconnected and reconnected. If it was only "modified" there would have been no disassembly of the control arms required. See the picture below. The picture shows the rear suspension parts. Notice that the upper control arm and the lower control arm bolt to the trailing arm. (which is what also houses the hub and bearing with the wheel speed sensor.) I hope this helps you to resolve your issue.

dttech_35.gif

Posted on Mar 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear lateral link 2004


Lateral Links TIme Lapse - YouTube

? 1:01
https://www.youtube.com/watch?v=g8zb_92T00s
Jan 20, 2014 - Uploaded by Tony Downs
Polished Sti lateral link install on 2008 Subaru Forester Sports XT. ... Replacing Rear Trailing Arm Bushings ...

Ikeya Formula Rear Control Arm and Lateral Link - YouTube

? 2:11
https://www.youtube.com/watch?v=0MAcEHsHKX4
Oct 21, 2008 - Uploaded by edoperformance
Ikeya Formula Rear Control Arm and Lateral Link ... How To Install Replace Rear Trailing Control Arm GM ...

How to Install Rear Lateral Links - i-Club




Dec 14, 2015 | 2004 Ford Explorer

1 Answer

Can I replace a rear trailing bushing on the vehicle without removing the entire trailing arm i want to use an on vehicle bushing press


You can. I remove the bolt and insert a block of wood between the arm and the body to help keep the arm lower and then press the bushing in and out

Nov 08, 2015 | 2004 Hyundai Sonata

1 Answer

How do i install lower trailing arms


best done with the weight on the vehicle remove the bolts going through the arm insulators and remove the arm. do one side at a time and try not to move the wheel. Lower trailing arms may have an washer on the bolts that is off set for alignment purposes so be careful as to where the washers are sitting or you will need a rear wheel alignment when finished.

Dec 25, 2014 | 1998 Ford Expedition

1 Answer

Bearing removal 87 Subaru right rear trailing arm


read the Chiltons manual (auto parts store) for your car

May 06, 2014 | Cars & Trucks

1 Answer

1.2ltr Fiat Punto Active... rear of car seems to wobble after corners and on two occasions has kicked out into a tail slide... and possible causes and fixes?


check the shocks, stabilizer bar links and bushings,trailing arm and lower control arm bushings and looseness in the rear wheel bearings.

Jun 09, 2012 | Cars & Trucks

1 Answer

How to install rear struts on a 1999 llexus


selectachapter.gif

Lexus Car ES, IS, LS 1998-06
Coil Spring Rear Suspension

Print


Hub & Bearings

Adjustment
Check the backlash in bearing shaft direction and the axle hub deviation. Maximum for backlash should be 0.0020 in. (0.05mm) and for axle hub deviation 0.020 in. (0.05mm).

7923lgb6.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Checking wheel bearings for excessive play


NOTE The rear wheel bearings are non-adjustable. If the wheel bearing is out of specifications, replace the wheel bearing.
Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Raise and safely support the vehicle.
  3. Remove or disconnect the following:

    Rear tire and wheel assembly Rear stabilizer link Rear axle shaft nut Rear disc brake caliper and disc Speed sensor Parking brake assembly at the wheel hub No. 1 and 2 upper control arm assembly No. 1 and 2 rear suspension arm assembly Toe control link Rear axle from hub assembly using a plastic hammer No. 2 rear wheel bearing dust deflector using a screwdriver 4 bolts and rear axle hub and bearing assembly from the axle carrier assembly

To install:
  1. Install or connect the following:

    Hub on the carrier and tighten the bolts to 52 ft. lbs. (70 Nm) No. 2 rear wheel bearing dust deflector using a screwdriver Rear axle into hub assembly No. 1 and 2 upper control arm assembly. Torque the new nut to the No. 2 rear upper control arm to 52 ft. lbs. (70 Nm). Temporarily tighten the No. 1 arm bolt. No. 1 and 2 rear suspension arm assembly. Temporarily tighten. Toe control link. Torque new nut to 52 ft. lbs. (70 Nm). Rear stabilizer link. Torque to 20 ft. lbs. (27 Nm). Parking brake assembly at the wheel hub Rear speed sensor Rear axle shaft nut. Torque to 214 ft. Lbs. (290 Nm) and stake the nut with a chisel and hammer. Rear brake disc and disc brake caliper
  2. Adjust the parking brake.
  3. Stabilize the suspension as follows :
    1. Install the wheel(s).
    2. Lower the vehicle and bounce it up and down several times to stabilize the rear suspension.
    3. Raise the vehicle.
    4. Remove the wheel.
    5. Jack up the rear lower suspension armplacing a wood block in between. Apply a load to the suspension so that the lower suspension arm is plkaced in a horizontal position.

  4. Fully tighten the No. 1 rear upper control arm assembly to 119 ft. lbs. (161 Nm).
  5. Fully tighten the No. 1 rear suspension arm assembly to 70 ft. lbs. (95 Nm).
  6. Fully tighten the No. 2 rear suspension arm assembly to 119 ft. lbs. (161 Nm).

    Rear tire and wheel assembly

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Raise and safely support the vehicle.
  3. Remove or disconnect the following:
    NOTE If it is necessary to replace the hub or bearing, replace the components as an assembly.


    Rear tire and wheel assembly If equipped with rear disc brakes, the caliper mounting bolts. Leave the brake line connected and suspend the assembly out of the way. Brake rotor or drum 4 bolts and pull off the rear axle hub O-ring

To install:
  1. Install or connect the following:

    Hub on the carrier and tighten the bolts to 59 ft. lbs. (80 Nm) Rotor or drum Caliper, f equipped with rear disc brakes and tighten the bolts to 34 ft. lbs. (64 Nm) Wheel

  1. Before servicing the vehicle, refer to the Precautions section.
  2. If equipped with air suspension, move the height control switch in the trunk area to the OFF position.
  3. Remove or disconnect the following:

    Negative battery cable Rear wheel(s) Height control sensor link from the lower control arm Anti-lock Brake System (ABS) speed sensor and wiring harness Brake caliper bracket from the rear axle carrier by removing the 2 bolts. Support the caliper with a piece of wire. Brake rotor Parking brake shoes and cable Cotter pin, lock cap and the nut holding the halfshaft to the rear axle Suspension member brace by removing the 2 bolts Halfshaft bolts and washers Halfshaft from the vehicle Strut rod
  4. Place matchmarks on the adjusting cam and body for the No. 1 control arm.
  5. Remove or disconnect the following:

    Nut and adjusting cam Nut on the axle carrier side of the No. 1 lower control arm Separate the control arm from the axle carrier No. 1 lower control arm Stabilizer bar link from the No. 2 lower control arm.
  6. Place matchmarks on the adjusting cam and body.
  7. Remove or disconnect the following:

    Nut and adjusting cam from the No. 2 lower control arm Nut and bolt holding the No. 2 lower control arm to the axle carrier No. 2 control arm from the vehicle Nut and bolt on the lower side of the strut assembly 2 upper control arm set nuts and bolts Axle carrier with the upper control arm
  8. Secure the axle carrier in a vise.
  9. Remove or disconnect the following:

    Nut holding the upper control arm to the axle carrier and remove the control arm Dust deflector. Use a suitable prytool. Oil seal

    0996b43f802092da.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the oil seal (inner)-LS 430

  10. Remove the 2 bolts and nuts and shift the backing the plate towards the hub side (outside).
  11. Remove or disconnect the following:

    Axle hub

    0996b43f802092db.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the axle hub from the axle carrier-LS 430
    Backing plate. Inner race (outside) from the axle hub

    0996b43f802092dc.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the inner race (outside) from the axle hub-LS 430
    Oil seal (outer) from the axle

    0996b43f802092dd.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the oil seal (outer)-LS 430
    Snapring from inside the axle housing Bearing from the axle housing


To install:
  1. Install or connect the following:

    New bearing to the axle housing Snapring to the axle carrier, using snapring pliers New outer oil seal. Coat the oil seal lip with multipurpose grease.

    0996b43f802092de.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Installing the oil seal (outer)-LS 430
    Backing plate to the axle housing. Do NOT install the bolts or nuts at this time. Inner race (inside) to the axle housing Axle hub to the axle housing Backing plate in position. Tighten the bolts and nuts to 43 ft. lbs. (59 Nm). New oil seal (inner) to the axle housing. Coat the oil seal lip with multipurpose grease.

    0996b43f802092e0.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Installing the oil seal (inner)-LS 430
    New dust deflector. Be sure to align the hose for the ABS speed sensor in the dust deflector and axle carrier. Upper control arm to the axle carrier by installing the nut. Tighten the nut to 80 ft. lbs. (108 Nm). Axle carrier and upper control arm to the vehicle as an assembly 2 upper control arm set bolts and tighten the bolts to 121 ft. lbs. (164 Nm) Bolt and nut holding the strut to the axle carrier. Tighten to 101 ft. lbs. (137 Nm). Bolt and nut connecting the No. 2 lower control arm to the axle carrier. Tighten the bolt to 60 ft. lbs. (81 Nm). Nut and adjusting cam to hold the No. 2 lower control arm to the body. Align the adjusting cam marks and tighten the nut to 57 ft. lbs. (78 Nm). Stabilizer bar link to the No. 2 lower control arm and tighten the nut to 48 ft. lbs. (65 Nm) No. 1 lower control arm to the axle carrier and body. Install the nut to hold the No. 1 lower control arm to the axle carrier. Tighten the nut to 43 ft. lbs. (59 Nm). Nut and adjusting cam to hold the No. 1 lower control arm to the body. Align the matchmarks and tighten the nut to 57 ft. lbs. (78 Nm). Strut rod to the axle carrier and body. Install the bolt and nut to hold the strut rod to the body. Tighten to 57 ft. lbs. (78 Nm). Bolt and nut to hold the strut rod to the axle carrier. Tighten to 136 ft. lbs. (184 Nm) Parking brake shoes and cable Outboard joint side of the halfshaft and align the matchmarks on the side gear shaft and the halfshaft. Coat the threads with clean oil and install the hexagon bolts. Tighten bolts to 61 ft. lbs. (83 Nm). Suspension member brace with the 2 bolts. Tighten the 2 bolts to 37 ft. lbs. (50 Nm). Nut to hold the halfshaft to the rear axle. Tighten the nut to 213 ft. lbs. (289 Nm). Lock cap and cotter pin Brake disc to the axle hub with the matchmarks aligned. Install the 2 screws and tighten the screws to 48 inch lbs. (5 Nm). Brake caliper to the vehicle and install the 2 bolts. Tighten the bolts to 77 ft. lbs. (104 Nm). ABS speed sensor and wiring harness Height control sensor link with the matchmarks aligned. Tighten the nut to 48 inch lbs. (5 Nm). Rear wheel(s) Negative battery cable

  2. Lower the vehicle and turn ON the air suspension switch.



0996b43f80207fdc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Exploded view rear carrier assembly, hub and bearing-

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    WARNING Be careful not to damage the boot and ABS sensor


    Rear wheel(s) Height control sensor link from the lower control arm Anti-lock Brake System (ABS) speed sensor and wiring harness Brake caliper bracket from the rear axle carrier by removing the 2 bolts. Support the caliper with a piece of wire. Brake rotor Parking brake shoes and cable Toe control link Separate upper control arm assembly Shock absorber from axle carrier Suspension arms No 1 and 2 from axle carrier Rear axle from carrier


    Wheel bearing dust deflector 4 bolts and axle & bearing hub assembly

To install:
  1. Install or connect the following:

    4 bolts and axle & bearing assembly. Tighten to 48 ft. lbs (65 Nm) Rear wheel bearing dust deflector Rear drive axle Upper control arm. Temporarily tighten No 2 and No 1 suspension arms. Tighten to 52 ft. lbs. (70 Nm) Shock absorber. Temporarily tighten Toe control link. Tighten to 37 ft. lbs. (50 Nm) Fully tighten upper control arm. Tighten to 52 ft. lbs. (70 Nm) Height control sensor Parking brake shoes and cable Speed sensor Rear disc brake caliper Fully tighten shock with new nut to 52 ft. lbs. (70 Nm) Rear tire
  2. Inspect and adjust rear wheel alignment
  3. Check ABS speed sensor signal

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Rear wheel Wheel speed sensor Axle halfshaft Brake caliper and rotor Parking brake shoes Parking brake cable No. 1 lower suspension arm bolt No. 2 lower suspension arm bolt Toe control link Upper ball joint Axle carrier from the vehicle
  3. Press the hub out of the wheel bearing, then remove the backing plate.
  4. Remove the snapring, then press the wheel bearing out of the axle carrier.

To install:

NOTE Use a new toe control link nut for assembly.
  1. Installation is the reverse of the removal procedure, while using the following torque values:

    Backing plate bolts: 43 ft. lbs. (59 Nm) No. 1 lower suspension arm bolt: 55 ft. lbs. (75 Nm) No. 2 lower suspension arm bolt: 81 ft. lbs. (110 Nm) Toe control link nut: 36 ft. lbs. (49 Nm) Upper ball joint nut: 80 ft. lbs. (108 Nm) Brake caliper support bolts: 77 ft. lbs. (104 Nm) Rear wheel lug nuts: 76 ft. lbs. (103 Nm)



0996b43f80208026.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Exploded view rear Axle carrier and hub assembly-ES 330

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Rear tire and wheel assembly Brake caliper support bracket Brake rotor Skid control sensor wire 4 bolts and rear hub and bearing assembly Skid control sensor

To install:
  1. Install or connect the following:
    NOTE Inspect bearing back lash and hub deviation


    Skid control sensor Rear axle hub and bearing assembly with 4 bolts. Tighten to 59 ft. lbs. (80 Nm) Skid control sensor wire


    Rear disc Rear disc brake caliper assembly. Tighten to 46 ft. lbs (62 Nm) Flexible brake hose Rear tire and wheel
  2. inspect and adjust rear wheel alignment
  3. Check ABS speed sensor signal


Stabilizer Bar

Removal & Installation

  1. Remove the rear wheels.
  2. Remove the 2 nuts and left stabilizer bar link. If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud. Repeat for the right side.
  3. Remove the 8 bolts, 2 No. 1 brackets and 2 bushings. Two types of bolts are used, so make sure the correct bolts are installed.
  4. Remove the stabilizer bar.

To install:
  1. Install the stabilizer bar.
  2. Install the bushing and bracket with the 2 bolts and tighten to 14 ft. lbs. (19 Nm). Install the bushing to the inner side of the bushing stopper on the stabilizer bar.
  3. Connect the stabilizer bar links and tighten the nuts to 29 ft. lbs. (39 Nm). Repeat for the right side.
  4. Install the rear wheels.
  5. Inspect and adjust rear wheel alignment.


Strut & Coil Spring

Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    CAUTION Do NOT remove the center nut to the strut at this time. The spring on the strut is under high pressure and can cause serious injury.


    No. 2 luggage compartment trim cover Left and right deck side trim box Rear luggage compartment trim cover Front luggage compartment trim cover Left and right side luggage compartment trim covers Rear wheel Rear wheel fender liner No. 2 differential support protector Rear suspension member brace Rear No. 2 lower control arm Mounting bolts and strut assembly
  3. Secure the strut in a vise.
  4. Compress the coil spring
  5. Remove or disconnect the following:

    Upper strut retaining nut Suspension support Upper insulator Bumper Coil spring Insulator

Dec 26, 2011 | 1999 Lexus ES 300

1 Answer

Want to know the relationship between the rear trailing arm and the control arm. If you had the rear trailing arm fixed because of recall then 2 months later they say the control arm came loose and broke...


The recall for your vehicle may or may not have included replacement of the trailing arm. The recall says that the trailing arm is to be "inspected" then it will be replaced, or modified at the discresion of the person performing the inspection. If it was "replaced", it would require the control arms to be disconnected and reconnected. If it was only "modified" there would have been no disassembly of the control arms required. See the picture below. The picture shows the rear suspension parts. Notice that the upper control arm and the lower control arm bolt to the trailing arm. (which is what also houses the hub and bearing with the wheel speed sensor.) I hope this helps you to resolve your issue.

dttech_35.gif

Mar 08, 2011 | 2003 Hyundai Santa Fe

1 Answer

Renewing rear springs bmw 318


remove lower shock bolt and rear wheels, pry down the rear trailing arm slowly and carfully so you dont break the sway link and remove old spring, lubricate the spring pads and reinstall,lower the arm onto a axle stand to re install the shock

Feb 17, 2010 | 1997 BMW 318

1 Answer

Procedure for replacing rear wheel bearings 2000 Forester


i'm assuming you don't have a hubshark,this is a tool that will alllow you to remove the bearing while the knuckle is attached to the car,you may be able to rent this tool at a auto prts store .if not you need to remove the entie knuckle,first remove the trailing arm bolt,then the lateral link bolt{long and stubborn bolt},disassemble the brake shoes and parking brake cable,abs sensor if equipped the knuckle to strut bolt{no marking necessary they are not eccentric} then you need a to use or borrow a press to remove hub and bearings good luck

Mar 22, 2009 | 2000 Subaru Forester

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...