Question about Cars & Trucks

1 Answer

2001 pt cruiser which wire is for the headlights and dash lights? Both lights are out....do I just need a bulb change

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 194 Answers

Both went out the same time? if so check your fuses and relays and the headlight switch.

Posted on May 09, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: PT Cruiser Brake Light

The bulb in the rear light has burned out and to replace it follow these instructions: 1) go to your owner's manual to find out the part number. You can find and purchase the replacement bulb at Target, any auto parts store and even at Walmart for under $4.00; 2) pop open the trunk door; 3) get a phillips screw driver and unscrew the 2 screws holding the rear brake light fixture to your car body; 4) as soon as you turn over the fixture you'll see where to pull out the burned out bulb and replace it with the new one(s). Good luck!

Posted on Oct 15, 2008

martin538
  • 117 Answers

SOURCE: Engine motor mounts on 2001 PT Cruiser

Place a block of wood under the engine sump to prevent damage when you jack up the engine to take the tension off the mount. Make sure you do not jack the engine up too much as you might damage the exhaust,cooling hoses etc.

Posted on Apr 07, 2009

BCAS1298
  • 3092 Answers

SOURCE: replacing a starter in a PT. Cruiser 2001

Remove battery and battery support you'll be able to undo starter bolt's trough there and slip starter out.

Posted on Dec 08, 2009

Testimonial: "This didn't help, because you had to remove the engine structural collar under the starter to get at the starter bolt. It was more complicated."

  • 5 Answers

SOURCE: 2001 PT Cruiser: How too remove crankshaft pulley 2001 PT Cruiser...

GET A 3 SPOKE PULLEY EXTRACTOR AND SCREW IN THE BOLT BUT IN THE CRANKSHAFT HOLE PUT A MUCH SMALLER SCEW SO YOU WOUNT MESS THE INSIDE UP

Posted on May 26, 2010

  • 1 Answer

SOURCE: need a wiring diagram for

i have wiring digrams for 2001 PT Cruiser from Mitchell On Demand. Just need to know which specific part needed diagram for.
for example here is charging system for 2001 PT Cruiser
61384d5.jpg

Posted on Oct 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The headlights on my 2001 Pt. Cruiser don't work. I've changed the fuses. What else could it be?


All the exterior lights run threw the turn signal switch, except the high mount brake light. So it could be the head light switch in the dash or the turn signal switch.

Sep 04, 2015 | Cars & Trucks

1 Answer

Yes, i have a 2003 chrysler pt cruiser and i just put a new battery in it now my dash, headlights and dome lights flicker real bad?


The issue seems to be common among the 2001-2005 models of PT Cruiser. Changing the battery (from other answers on other years with similar issues) seems to short out things like the lights and the stereo. Some suggestions for fixing it, if you can't find where the electrical wiring for the lights attaches to the battery/computer, to make sure the wires aren't frayed, the plastic housing isn't worn away, and the grounding wire hasn't been severed...then a mechanic should be able to find them for you.

Oct 04, 2014 | 2003 Chrysler PT Cruiser

1 Answer

FLASHING DASH BOARD LIGHTS 2006 PT CRUISER


Change your dashboard light switch/dimmer. It either has a bad connection, or is faulty altogether.

Dec 04, 2013 | 2001 Chrysler PT Cruiser

1 Answer

I have a 2002job pt cruiser. The dash illumination lights do not work. Neither do the climate control lights. The fuse is good. Any suggestions?


Check the voltage past the fuse and the wires comming from the relay, check the relay also. Do your headlight come on?

Feb 22, 2012 | 2002 Chrysler PT Cruiser

1 Answer

I have an 06 pt cruiser and my lowbeams will not work. I have changed bulbs and I have checked all the fuses. I tried to install a H.I.D kit when the lights started flickering then went out. Please help.


this sounds like a bad head light switch, you have replaced the bulbs and all fuses are good then i would say try the headlight switch. there is testing you can do to make sure thats the problem but you will need a test light and also a assume the highbeams work. this is a common problem when the headlights start to flicker its due to a switch most times, if was just one light then i would say to check the wiring to light but as its both then i would start with a new or used headlight switch.good day

Oct 18, 2011 | 2006 Chrysler PT Cruiser

1 Answer

Replace turn signal bulb on a 2001 PT cruiser


You simply remove the screws that hold the light in , pull it out, twist old bulb out and change it

Sep 14, 2009 | 2001 Chrysler PT Cruiser

2 Answers

2001 PT cruiser. Turned on headlights and they didn't come on. The instrument lights are also out along with the power door locks. all fuses are good, inside and out. Anyone have this problem. Need a...


I have a 2002 and one day had no headlight or dash lights. The tail lights, blinkers and hazards work just fine as do the radio of dome lights. Changed the multi-function and checked all fuses, but no help. I am interested in the solutions as well.

Apr 20, 2009 | 2002 Chrysler PT Cruiser

1 Answer

Trying to remove headlight assembly to change turn signal bulb on


you need to take off front bumper to get the bottom bolt

Jan 23, 2009 | 2003 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...