Question about 1998 Toyota RAV4

1 Answer

Ihave chvey impla with ing 3.9 liter the car cam with no padal .we cange the master cilinder and still no pedal wath cood be ?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Air in the system. either due to a leak or you need to bleed the system after installing the new master cylinder.

Posted on May 06, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1970 ford cortina , the brakes padal fades every now and again


Air in the line. Could be a faulty caliper, to test a caliper clamp off the line with vice grip on each tyre and test pedal. If you get good pedal when a line is clamped you have found your problem caliper.

Jan 15, 2013 | 1970 Ford Cortina

2 Answers

97 saturn brake problems. Replaced master cylinder, both front calipers and rotors. Replaced both rear wheel cilinders shoes and drums. Also replaced all rubber brake lines yet no pedal after bleeding....


Get another master cylinder,If you want to really find out if the master cylinder is goo open one of the lines have someone pump the brake,with your finger over the open cylinder line you will have pressure coming out, and if you feel vacuum has your assistant releases the pedal that a sure sign the master cylinder is not working,Also when you have a master cylinder before you install you need to bench bleed it

Nov 28, 2012 | Cars & Trucks

3 Answers

Brake pedal sinks to floor


Losing fluid somewhere or losing pressure in the master. Will need to be serviced by a shop. Can't drive it this way.

Sep 10, 2012 | 2005 Mazda 3 Sedan

3 Answers

2005 ford f150 brake light on dash stay on


Some speed wheel sensor got o bad or need adjust.

Oct 24, 2011 | 2004 Ford F150

1 Answer

How do i reset the oil mileage ofter oil change on a 2005 sileverado im at vbfudgeshop@yahoo.com i know you hit brake padal 3 times in a certon patern


turn key to run but dont start engine and push the gas pedal to the floor 3 times the light should flash then your done.

Apr 17, 2011 | 2005 Chevrolet Silverado

1 Answer

Clutch pedal droped raisded back by hand pedal does not depres engine does not start


It sounds like your clutch master or slave cilinder has gone bad .you should be able to locate clutch cylinder under hood usually drivers side check fluid level if low replace master or slave cylinder.

Nov 26, 2010 | 2004 Hyundai Santa Fe

4 Answers

The clutch pedal is rock hard won't go in too gear checked the clutch master cylinder and thats ok, so do you know what the problem is.


Possible solution! Daewoo Lanos 98-99
Had the same problem suddenly the clutch pedal went rock hard!
The clutch was around 3 months old.
Mechanic checked - Master, Slave, Clutch Components, and inside the box, all looked okay.
Turned out the top arm of the clutch pivot rod had twisted, replaced pivot rod around AU$100.
Fixed Problem!

68f141a6-6e26-4193-91d9-bdf12856e824.jpg 8ee95b47-7be0-4e27-81a1-a4ccf7bbc122.jpg

Apr 16, 2010 | 2004 Land Rover Discovery

1 Answer

I changed the front brake and the calipers plus master cilinder then I try it to drive the car, but in 2 minutes I dont feel the brakes, I pushed the pedal allway down to the end there are no brekes at...


Sounds like you have air in the system, or maybe a defective master cyl.did you bench bleed the master cyl. before you installed it? You will have to bleed the system of air starting with the RR, LR, RF, LF, If you don't get peddel after that than most likely its a defective master cyl.

Oct 21, 2009 | 1997 Chrysler Sebring

1 Answer

I replaced the mas cyl 2004 ford explorer. Gas padal won't work


You need to bleed the air from the system. First if you replaced the master cylinder you need to bleep both ports that the line hook too. Then hook the lines up and bleed all four corners of the vehicles brakes starting with the right rear since it is the furthest point away from the master cylinder. As you bleed the system remember to refill the master so you don't' ingest more air into the system again.

May 20, 2009 | 2004 Ford Explorer

2 Answers

Brake problem


Did you use DOT # 3 Brake fluid to fill up the master cylinder like your suppose to or did you use DOT #5 that your not suppose to use???find that bottle let me know asap.John

Feb 15, 2009 | 1990 Nissan Sentra

Not finding what you are looking for?
1998 Toyota RAV4 Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...