Question about Chevrolet Uplander

Open Question

Codes U1300, U1301, P1626,P1811

Car starts fine most times but last few days turn key noting con=mes on? play with it for a while I jiggled the drives side door switch and car started ran fine! did get antitheft system service displayed on dash!

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
280zlvr
  • 126 Answers

SOURCE: Starting problems with 98 intrigue

please remove all extra keys and gadjets from keyring and go through the painful exercise of starting the old girl and once started go for a drive good luk if all goes well replace ignition switch good luck with this answer

Posted on Jun 30, 2008

Ad
  • 393 Answers

SOURCE: won't start. clicking under

sounds like a poss loose ground check all bat connections for corrosion/tightness.

Posted on Nov 11, 2008

  • 109 Answers

SOURCE: Ignition key turns on but car will not start

I suspect the ignition switch is malfunctioning.

Posted on Nov 19, 2008

  • 3600 Answers

SOURCE: car will not turn off

You have a bad ignition switch the mechanical part is operating but when it is turned off it is not pulling the switch to the off position, two things that I can think of can cause this. One is the rod that runs down the steering column is slightly bent from wear over time and allows it to start but when the rod moves in the reverse direction the bent rod is slightly to high to pull the switch to the off position. The other problem could be with the switch itself the return spring inside the switch could be broken so the switch does not turn off. You can remove the bottom kick panel and disconnect the battery then with a flash light look on the top of the column and see if you can see the rod moving when turning the key off and on if it's moving then it is the adjustment of the rod or the switch. To remove the switch you will have to drop the steering wheel down to get to the switch, you may be able to get to the switch without dropping the column but it will be harder to see what is wrong with it. There are two bolts that hold the switch on and has a multi flat connector on it you have to squeeze the two plastic ears on each end of the switch to release the wire harness. Then you will have to wiggle the connector loose

Posted on Sep 12, 2009

  • 355 Answers

SOURCE: Possible security light problem on 1999 pontiac firebird...

if you have the chip in the key, then this will surely help you: http://newrockies.com/vatsbypass . It was the only thing that saved my car.

Posted on Mar 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My remote key fob stopped working after i dropped it in water. The door locks don't open with the key , they seem to be jammed. The passenger side door unlocked a few times with the key after jiggling it a...


It might work if you disconnect your battery for 10 minutes to clear the old Code and then reconnect it before you try to program the new FOB.

Oct 18, 2013 | 2000 Ford Taurus

3 Answers

Car Won't Work. HELP!!!


did you check battery could be death.Gas pedal is moving,under steering wheel any wires damaged.It is full park position.

Apr 30, 2013 | 2002 Pontiac Grand Prix

1 Answer

I have a VW Golf 01 and the key fob opens and shuts the doors fine. But as soon as i put the key in the ignition to start the car it wont start all lights go off and the alarm goes off. Help please!


Okay, this sounds like theres a problem with the switch inside the door, try this, go to the passenger door and unlock it with the key, note if it has a lock, most newwer cars are only putting locks on drivers door, but if it has one use the key to unlock it and then try to start the car, if theres no lock then try the truck lock, unlock it with the key and try to start the car, if that doesnt work then use the fob to unlock all doors by pushing it two times and then start the car, the problem is the switch inside the door lock, this switch is part of the latch asm, good day.

May 05, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

My 95 Ford Windstar has just developed a rather distressing problem. In the morning, I get in my van and everything is fine. A few hours later, when I get in my van and start it, there is a warning bell...


one of the door ajar switches are sticking. needs to be put on the computer to find out which one. only other way is to go around and unplug the switches until your light shuts off.

Mar 30, 2011 | Ford Windstar Cars & Trucks

1 Answer

For the last few days my 2000 Saturn LS has been having issues when I try to start the car. When I put turn the key all the electricity dies. Popping the hood and jiggling the battery restores the...


if you can jiggle the battery cable, its loose. or dirty,tighten the cable ends...tight. You may need to disconnect the battery and make sure that the ends are clean and bright.

Dec 08, 2010 | 2000 Saturn SL

2 Answers

The key wont turn at the final point to crank the car, last year my tumble broke, i had it fixed but when it broke i couldnt move the key at all, its not doing thay this time, 2 days ago i went to the...


Not an exact solution, but perhaps information that might lead to one.

1.Replaced the tumblers? I believe I would replace the entire ignition switch this time. It's my belief that the body of the ignition switch is worn inside, and will keep damaging the tumblers.

2.Do you have a tilt steering wheel? It's best to keep the steering column in straight line when starting the car, then tilt the wheel to where you want, after the car is started. When the steering column is in a tilted position, it puts undue strain on the ignition key switch, and the mechanism the ignition key switch operates, on GM vehicles.

This mechanism, consists of a half moon gear on the ignition key switch, that turns inside a 'Planetary' gear. I used the term 'Planetary', as the gear shape is hard to describe. It resembles an oblong loop, shaped like the number 9, with gear teeth on the inside bottom of the loop. This 'Loop' rotates, when the gear teeth of the ignition key switch, engage the teeth on the loop, and pushes a rod, or retracts the rod. The rod goes down the side of your steering column, and turns on, or turns off an ignition switch, located at the bottom left side of the steering column.

Having the steering wheel tilted, puts a strain on the ignition key switch internals, the oblong loop can break, and/or gear teeth can be stripped off.

May 18, 2009 | 2002 Pontiac Sunfire

1 Answer

1995 Chrysler Concorde


the alarm is activating when he locks it and for some reason the key or fob isnt deactivating it..check the disarm switches in the door

Aug 11, 2008 | 1995 Chrysler Concorde

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...