Question about 1999 Daewoo Lanos

1 Answer

I have 2 door 1999 lanos. My car's driver side front and rear window glass had smashed so i wanted to fit new one. But i don't know how and where i could fix my problem.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 208 Answers

And all service glass dealer look in your local phone directory

Posted on Jun 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I correct wind noise on drivers side door / window 1999 Camry?


There may be a torn, missing, or loose door gasket. If you inspect the seal and find torn or missing segments, repair or replace. If the seal is intact, the the most likely cause is a gap in the door seal near the top rear of the door. This happens over time because the door frame can actually get bent slightly outward. It is so little as to not be visible, but you can hear the wind noise. The way to get the noise to stop is to open the door and roll the window all the way down. Then, holding the door firmly, grasp the upper rear corner and pull it inward (toward to the car). A couple of sharp tugs will usually do the trick. I know it sounds silly, but it works. BE SURE TO HAVE THE WINDOW DOWN OR YOU COULD SHATTER THE GLASS!
The door frame is quite thin compared to other car body parts and will bow/bend if you pull on it. Start out carefully and if you don't get the results you want, try again with more force.

Nov 21, 2014 | 1999 Toyota Camry

1 Answer

2007 toyota solara convertible rear window smashed


take the vehicle to an accredited windscreen repairer/ replacer and discuss the problem with them. If it can be done they will have access to the glass and will be able to tell you where to get it fitted if it requires specialist attention.

Feb 15, 2014 | Toyota Cars & Trucks

2 Answers

My front drivers side electric window has stopped working it wont go up or down


those things last about 10 years, and the most used window generally dies first, go figure. Find and buy a new window regulator on eBay or at a parts store. If you can not find one you will have have to pay through the nose at a dealer parts department. Do not just buy a lift motor, you want an entire new regulator which includes a motor.

Take the car and the new regulator to a glass shop which does auto glass. For about 50 bucks they will put it in for you. That is a bargain.

Mar 22, 2011 | 1999 Daewoo Lanos

1 Answer

I need to replace the drivers front window winding cable. how do i do that ? thanks Ants


best to buy this as an assembly. remove the drivers door panel behind the door is the window motor and regulator assembly. unbolt the regulator from the glass and remove the glass or prop the glass in the up position unbolt the motor and remove the assembly from the door and reinstall the assembly be carefull to position the nuts for the glass and make sure the pads that protect the glass are in place dont over tighten the nuts on the glass part or you will explode the glass

Jan 20, 2011 | 1999 Daewoo Lanos

1 Answer

I need to install a window in my vw polo. It is the back seat pasanger side window, i have already purchased it and have the inside panel off. My issue is fitting the window inplace without it smashing,...


We don't have Polo in the States but it would be the same design as a Golf or even a Jetta, even a Passat.
  1. Remove nuts from glass clamping jaws, press jaws apart, an access port would reveal both nuts at the same level
  2. Lower door glass into door, pull window channel (Window rubber gasket) out of door frame and remove center connector (metal channel strip that separates vent window. A screw on top and a hex head screw at bottom)
  3. Pull door glass upward, tilt toward front and lift out of window slot
  4. Install in the reverse order of removal
Note: Clamping jaw hex nuts torque spec.......10Nm (7ft-lb)

May 04, 2010 | 1998 Volkswagen Golf

1 Answer

Driver's side window smashed


phillips screw driver, 10mm socket/rachet, vaccuum cleaner and yes you can. one of the more simple glass installations.

Sep 14, 2009 | 1998 Toyota Camry

1 Answer

Fallen driver's side window


probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screws from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
  1. Remove the two front door brace bolts and the front door brace.


    415712f.gif

  1. Disconnect the front window regulator electric drive electrical connector.
  1. Remove the four front door window glass regulator track bolts.

    67b6136.gif


  1. Remove the three front window regulator electric drive bolts.
  1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
  1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
  1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
  1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

Apr 29, 2009 | 1998 Mercury Villager

1 Answer

Rear side windows


This may be just a case of inadvertently hitting the window lock out n th driver door window switch by mistake. Check that first. Here's some background on window operation

Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Symptom Chart Condition Possible Sources Action
  • All windows are inoperative
  • BJB Fuse:
    • F20.
  • Circuit.
  • Power window relay.
  • Front door power window switch.
  • GO to Pinpoint Test A .
  • Single power window is inoperative
  • Front door power window switch.
  • Front door power window regulator.
  • Circuit.
  • Driver door power window switch.
  • GO to Pinpoint Test B .
  • Vent power window is inoperative — quarter window glass power latch
  • Circuit.
  • Quarter window glass switch.
  • Quarter window glass power latch.
  • GO to Pinpoint Test C .
  • The one touch down feature is inoperative
  • Master window regulator and door lock switch.
  • INSTALL a new master window/door lock/unlock switch. REFER to Switch—Master Window Door Lock/Unlock .
  • The back window will not defrost
  • CJB Fuses:
    • F30 (10A).
    • F32 (20A).
    • F34 (20A).
  • BJB Fuse:
    • F27 (45A)
  • Circuit.
  • Heated back window switch.
  • SEC/timer module.
  • Rear window defrost relay.
  • GO to Pinpoint Test D .
  • The back window defrost will not shut off automatically
  • SEC/timer module.
  • Circuit.
  • Rear window defrost relay.
  • GO to Pinpoint Test E .

Jan 28, 2009 | 1999 Mercury Villager

1 Answer

I need to replace the rear driver side window...the tiny one


remove the interior cover of your rear door. you will find this small metal post with size 10 bolts holding your glass. take out the bolts and loosen it to insert your new glass. if some door mechanism gets in your way, loosen it a little to give you space. its a bit tight there.

Nov 11, 2008 | 1997 Toyota Corolla

1 Answer

Replacing a side mirror


try taking the glass out the bolts should be somewhere in there

Sep 16, 2008 | 1999 Daewoo Lanos

Not finding what you are looking for?
1999 Daewoo Lanos Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...