Question about Ford Ranger

Open Question

Replacement of timing chain on 2013 ford ranger xlt

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76630 Answers

SOURCE: heater core replacement

It's one of the easiest cores to replace that I have encountered. Disconnect heater hoses at firewall. Probably doesn't matter about hose placement, but I always mark them just in case. To remove the fiber cover under dash, take a flat blade screwdriver and pry out the center pin of the expansion clips that hold it in place. There are four 5/16 head screws that hold the bottom/drain tray cover. Core will pull through the firewall and then down. You may have to silicone/glue or replace the foam seal strips on the new core. Before you install the core, check the distance between the inlet and outlet tubes to ensure they match the openings in the firewall. This saves time. It helps if you have someone on the outside to guide you when stabbing the tubes through the firewall. Replace bottom cover. You may have to hold one of the tubes when reinstalling the first hose to the core. Replace any lost coolant and check for leaks prior to reinstalling the fiber cover. If the cover seal is in good condition, any leak should drain through the firewall, otherwise it may leak inside cab. .

Posted on Sep 10, 2008

Ad
  • 195 Answers

SOURCE: 2001 Ford Ranger V6 timing chain

Hello;
The Ford motors are pretty good. I had 280K on a 2.9 V-8 that only needed the oil changed every 3K. Unless you have fluctuatuation in the timing then you should be ok.
These engines use a chain rather than a belt and have excellent life.
Thanks;
Rich RPM Northwest

Posted on Jul 01, 2009

jturcotte
  • 8516 Answers

SOURCE: 1998 ford ranger xlt 2.5

These are not very good but all I could find. The cam mark is about the 7 o'clock position. I cannot see the crankshaft marks in the side pic.
25f432e.gif
ffc6e4d.gif

Posted on Sep 19, 2010

  • 7 Answers

SOURCE: How to replace a 1987 ford ranger xlt heater core.

on the firewall you will see the two hoses going though it,it will have hose clamps on them,remove them,remember or mark witch side they go on,now, under the dash in the passenger side you will see the black box, it has 4screws to it, remove them,then pull the cover off,you will see the coils,get ahold of it,wiggle it towards you,also moving up and down, lightly,lightly, now installing is same but reversed,now i would hold one of the small tubes and install the hose,cause it will slide back and possiably fall out,be carefull,if you are having trouble getting the hose on the tube,use alittle lube,you can do it,just take your time..

Posted on Oct 10, 2010

ZJLimited
  • 17970 Answers

SOURCE: 2001 ford ranger 4.0 engine timing chain

Hi Josiah:
According with the repair guide...4.0L Engine

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Engine from the vehicle Oil pan Engine front cover Cylinder heads
  4. Lock the jackshaft tensioner by installing a pin.
    Jackshaft sprocket and chain assembly Left front cassette retaining bolt Cassette chain and tensioner assembly Rear jackshaft plug from the engine Right rear cassette retaining bolt and spacer Right rear cassette chain and tensioner Timing chain (s)

12_20_2011_4_41_36_pm.gif

Fig. Remove the jackshaft sprocket-4.0L SOHC Engine 2000-2001
Zooming link for Remove the jackshaft sprocket-4.0L SOHC Engine 2000-2001

To install:

  1. Install or connect the following:
    Timing chain(s) Right rear cassette chain, tensioner and sprocket Jackshaft sprocket and chain on the engine and remove the tensioner pin
  2. Torque the jackshaft sprocket bolt in 2 stages:
    1. 32-35 ft. lbs. (43-47 Nm).
    2. Turn an additional 65 degrees.
  3. Install or connect the following:
    Cylinder heads Front cover Oil pan Engine to the vehicle Negative battery cable
  4. Fill the engine with clean oil.
  5. Start the vehicle, check for leaks and repair if necessary.

  1. Before servicing the vehicle, refer to the Precautions section.
  2. With the vehicle in neutral, position it on a hoist.
  3. Remove the intake manifold.
  4. Remove the fuel supply manifold.
  5. Remove the accessory drive belt.
  6. Remove the thermostat housing.
  7. Remove the roller followers.
    NOTE You must retime the LH and RH camshafts when either camshaft is disturbed. Turn the crankshaft clockwise to position the number one cylinder at top dead center (TDC).

    NOTE The special tool must be installed on the damper and should contact the engine block to position the engine at TDC.
  8. Install the special tool.
    NOTE The right-hand camshaft sprocket bolt is a left-hand threaded bolt.
    NOTE If necessary, use camshaft gear torque adapter to loosen the camshaft sprocket bolt.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Posted on Dec 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford ranger 2008 3.0 xlt spins only but the engine does not run


run fault codes '
check for problem timing belt or chain

Sep 16, 2017 | Ford Cars & Trucks

1 Answer

I am in need of under dash fuse panel diagrams backside power side 92 Ford ranger xlt.


Confused by 'backside power side', but

Just Google

92 Ford Ranger XLT fuse box
And look at the Inage tab.

Or if you are after wiring details

92 Ford Ranger XLT wiring schematic

Jan 26, 2016 | Ford Cars & Trucks

1 Answer

Where is the in line fuseable link located on a 94 ford ranger 2.3 motor


    Alternator fuse link repaired my way. - YouTube

    ? 2:10
    https://www.youtube.com/watch?v=xgJQXKESDcI
    Dec 24, 2013 - Uploaded by Potskie
    I had the exact same situation with my ranger. ... I found thefuse links for the charge or alt output but not the one I ..... In line fuse, battery, or alternator? ... Of Key-Off Battery Drain (Parasitic Draw) - Duration: 18:14. by Motor Age.Missing: 2.3

    Fusible links and inline fuses? - Ford Truck Enthusiasts Forums

    www.ford-trucks.com/forums/885708-fusible-links-and-inline-fuses.html
    Sep 17, 2009 - Location: Kuna ID ... The PO had replaced one of the fusible links with an inline 30amp fuse. .... 81-F-150-Explorer is a splendid one to behold .... to charge the battery goes through that link when needed, and/or the battery to the other components when the engine is off. ... 91 ford ranger 2.3 daily driver 1994 Ford Ranger XLT 2.3L man. trans. - Ford Truck ...
    Jul 6, 2014
    86' Ranger cutting out!!! Fuel ? - Ford Truck Enthusiasts Forums
    May 10, 2012
    90' 302 fusible link for fuel? - Ford Truck Enthusiasts Forums
    Nov 2, 2010
    1988 ranger headlights won't work??? help - Ford Truck ...
    May 17, 2009
    More results from www.ford-trucks.com
    Missing: 94 images for Where is the in line fusible link located on a ...

Dec 30, 2015 | Ford Cars & Trucks

1 Answer

Ford Ranger radio wont work


You need to enter the ford audio units security code into the audio unit. Because the battery was out for a long time, the audio unit has forgotten its security code. The code is in the manual that came with the car.

Dec 20, 2013 | Cars & Trucks

1 Answer

2.5l V4. Como sincronizar cadena de tiempo?


Motor Ford 2.3 Lts. 16 V. Sincronizaci?n Timing chain kit ...

? 8:18
https://www.youtube.com/watch?v=QEzqopUjSak
Jun 10, 2013 - Uploaded by Carlos Parra Cort?s
Saludos no se usa un diagrama para sincronizar se tiene que poner ... ... Ford Escape & Fusion 2.3L 2.5L DOHC Engines: Valve Cover Gasket ... COLOCANDO LA CADENA DE TIEMPODE MAZDA 3 FORD ECO ESPORT ...

Sincronizaci?n de cadena de tiempo tracker - YouTube

? 0:13
https://www.youtube.com/watch?v=oFb44LJ9msY
Jun 6, 2014 - Uploaded by tonyeldogor
Puntos de referencia de cadena de tracker. ... 2001 Chevy Tracker V6 2.5L Head Instal and Timing Chain Instal - Duration: 25:45. JunkStar ...

Montaje de cadena de tiempo Zuzuki XL.7 - YouTube

? 3:52
https://www.youtube.com/watch?v=4k73S3dg5mI
Jun 21, 2014 - Uploaded by carmax100pre
Se demuestra solo es montaje de la cadena de tiempo. ... 2001 Chevy Tracker V6 2.5L Head Instal and Timing Chain Instal - Duration: 25:45.

Ford ranger 2.3 motor argentino CADENAS A TIEMPO ...

? 5:03
https://www.youtube.com/watch?v=8dR8mo8Ooy4
Jul 1, 2013 - Uploaded by eduardo soledad valencia



Jan 22, 2013 | Ford Mondeo Cars & Trucks

3 Answers

2001 Ford Ranger V6 timing chain


Hello;
The Ford motors are pretty good. I had 280K on a 2.9 V-8 that only needed the oil changed every 3K. Unless you have fluctuatuation in the timing then you should be ok.
These engines use a chain rather than a belt and have excellent life.
Thanks;
Rich RPM Northwest

Jul 01, 2009 | 2001 Ford Ranger Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...