Question about Cars & Trucks

1 Answer

How do I stop the leak from my manifold on my ttr90

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has answered 20 or more questions within one hour.


    An expert who has answered 20 questions.

  • Expert
  • 100 Answers

New gaskets...

Posted on May 08, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Mechanic put bars stop leak in my 1999 grand am se and it is running hot and wany hold coolant

Gm used the Barrs stop leak right from the factory to seal up new blocks. It was the kind made from walnut shells not the metal sealant. He may have used too much if you are overheating. I would do a good flush and go get the bars stop leak in the tablet form, follow directions and see if that helps. I had a persistent leak from my lower intake manifold, already replaced it once, put some Barrs in and now have zero leakage, no overheating either. I would have re-replaced the manifold's gasket but the car is just a beater. Now this stuff is a bandaid not a repair. So if you push the car hard the leak will reemerge.

Jul 13, 2014 | 1999 Pontiac Grand Am GT

1 Answer

Manifold bolts stripped out can't connect my exhaust wat should I do I have yamaha ttr90 needing someone to walk me through

remove the manifold and use vice grips to grad the affected studs . Apply plenty of grip on the stud and screw out . Replace with good studs using a stud installer or double lock 2 nuts on the stud to enable you to screw it in.

May 06, 2014 | Cars & Trucks

1 Answer

What do I use to remove studs on my manifold yamaha ttr90

Use a penetrating oil, then tap with a hammer (wood in between) and leave overnight. If still stubborn heat up a little with a blow torch. Put two nuts on the stud and tighten against each other. Using the lower one then undo.

May 06, 2014 | Cars & Trucks

1 Answer

Exaust intake leaking

It's exhaust manifold. There are two manifolds, the intake manifold in the valley between the cylinder heads, and the exhaust manifolds, one on each side of a v figured engine.

And, yes, a leak in the exhaust or the intake will make it run lean. If the leak is close to the engine, it can do harm to the valves, too. There is a gasket between the exhaust manifold and the engine block. Likewise, there is an intake manifold gasket between the intake manifold and the block.

Apr 04, 2014 | 1998 Ford F150 Regular Cab

1 Answer

Oil leak above starter and hits exhaust manifold

Rocker cover gasket must be leaking. Sometimes just tightening the cover bolts will stop it. Otherwise replace the gaskets.

Jan 28, 2014 | 2000 Chevrolet S-10

1 Answer

2001 acura cl stype exhaust smell comes into the car after coming to a stop

leaking exhaust manifold gaskets or cracked manifold, leaking exhaust.

Dec 16, 2013 | Acura CL Cars & Trucks

1 Answer

2000 mustang v6 has p0174 code. no leaks from hoses or anything external (vacuum) exhaust has no leaks. car runs bad uphill $ shudders from stopping at stop sign and accellarating. p0174 indicates bank 2...

Hi, have you checked for intake manifold gasket leaks? Pretty common on Ford V-6. With engine running, spray carb cleaner on the gaskets. If the engine speed changes, you have a gasket leak (yes, driver's side of the manifold).
Thanks for using FixYa.

Jan 23, 2011 | Ford Mustang Cars & Trucks

1 Answer

Had a mechanic try to fix exhaust leak @ manifold, they broke bolt off then tapped hole @ an angle. still have leak.can I double up on the gasket to possibably fix problem

If you think that the angled stud is stopping the manifold tightening enough to seal, an extra gasket could possibly fix the leak. If possible it would be better to **** the hole in the manifold so that it could pull up tighter on one gasket.

Aug 19, 2009 | 1988 Subaru GL-10

1 Answer

1995 Taurus leak around under intake manifold

just replace the intake gasket not the whole intake manifold

Mar 18, 2009 | 1999 Ford Taurus

1 Answer

Exhust manifold leaking

These are nasty manifolds... they are prone to failure at any or all of the weld points due to the extremely high temperature that they are repeatedly exposed to and must cool off from. Sadly, the manifold is retardedly difficult to replace and match correctly to the engine's head so it is best to replace the head and manifold in a pair from the same donor car. These manifolds are nearly impossible to repair, especially due to the location of the studs, etc. good luck man

Jun 20, 2008 | 1986 Audi 5000 CS

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14405 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides