Question about 1994 Ford F150 Styleside Supercab

Open Question

Heatsink paste installing ignition control module 1994 ford

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: ignition control module location for 1997 ford thunderbird?

1997 Ford Thunderbird Transmission problem
When driving normally transmission surges like it is not in gear. Had sensors replaced, nitural safety switch, and still acts up.

Posted on Dec 18, 2008

Ad
  • 29 Answers

SOURCE: How do you install a 4x4 control module for a 2004 Ford Explorer.

do you mean the elect. control module if so it is behind the radio youll will need the radio tools to take the radio out they can be found at most any parts stores.

Posted on Mar 06, 2009

chuck943
  • 783 Answers

SOURCE: location of ignition control module

It does not have an ignition control module.
The electronic ignition (EI) for the 4.0L engine consists of the following components:
Crankshaft position sensor (CKP sensor) and 36 minus 1 tooth trigger wheel.
Ignition coil .
powertrain control module (PCM) .
Related wiring.
The PCM controls the firing of the coil based on the signal from the crankshaft position sensor.
The crankshaft position sensor (CKP sensor) is a variable reluctance-type sensor, triggered by a 36 minus 1 tooth trigger wheel configuration machined into the rear of the crankshaft vibration damper. The signal generated by this CKP sensor is called a CKP signal. The CKP signal provides the base timing and rpm information to the powertrain control module (PCM). Base timing is set at 10 degrees BTDC and is not adjustable.
If vehicle has no spark then turn key to on position,check engine light should come on.As you start cranking engine it should go out while cranking after about 10 secs. it should come back on(while cranking). If it come on then the PCM sees the signal,if it does not then PCM is not seeing it and this is your problem,either the CKP sensor or the wiring to it.

Posted on Mar 16, 2009

chuck943
  • 783 Answers

SOURCE: where is the ignition module control located on 1996 ranger 2.3 e

It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Posted on Apr 08, 2009

  • 335 Answers

SOURCE: how to replace ignition control module on a 1994

Depending on your engine, if its located on the distributor remove the two screws/bolts that secure it pull downward to take it off, then slide the new one upward and put your screws/bolts back in, if you have the ignition module on the driveside fender same instructions.

Posted on Jan 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes the spark controller to burn out?


Either engine computer (ecu) or ignition control module. It may have different names like power transistor unit, ICM, ECM etc. Power runs from engine computer to ignition module then that powers the coilpack/coils. Also check the ground connections as they corrode over time. If you replace any units make sure the make a great connection and use any heatsink paste required

Feb 21, 2015 | Cars & Trucks

1 Answer

No start 1994 ford bronco


The spark problem is first because the computer uses the same signals to control injection Ford used two types of ignition systems #1 closed bowl this has the control module mounted on a heat sink next to the drivers hood hinge and 6 wires coming out of distributor or thick film where the module is mounted on distributor on both systems need to test the pick up coil with a logic probe for cycling voltage ok replace module if not ok replace pick-up coil.

Apr 19, 2014 | 1994 Ford Bronco

1 Answer

1994 ford thunderbird no power at heater blower motor control module


I've had the same problem with my 1994 Cougar XR7. It wasn't the module control. It wasn't the fan. It was a bleepin' inline fuse; a 30. Changed the fuse and everything was working fine. That's after I had purchased a new fan motor and electronic control module. None of the book or web pages I have read mentioned that fuse, which for some reason, Ford didn't put in the fuse box with the others. So, check your inline fuse, it may be just that. And it is located past the fuse box under the dash. It'll be the same thing for the T-Bird.

Dec 04, 2011 | 1994 Ford Thunderbird

1 Answer

How to replace ignition control module on a 1994 ford f150


Depending on your engine, if its located on the distributor remove the two screws/bolts that secure it pull downward to take it off, then slide the new one upward and put your screws/bolts back in, if you have the ignition module on the driveside fender same instructions.

Jan 19, 2011 | 1994 Ford F150 Styleside Supercab

2 Answers

Trying to locate the ignition module for chevy blazer s10 1994


Ignition module sits in the ignition distributor, remove distributor cap, there will be two elec. harness plugs, the one with two wire's is for the pick up coil, the other one is for the ignition module, just unscrew module out of distributor and install new one.

Sep 23, 2010 | 1994 Chevrolet S-10 Blazer

1 Answer

I need a schematic to replace the PCM (Powertrain Control Module)in my 1994 Fodr thunderbird 3.8L V6 without/supercharger ..Is this is Big job for a backyard mechanic and how long should it take, my real...


  1. Easy job and should have no problems here some help
    Disconnect the negative battery cable.
  2. Detach the engine control sensor wiring connector from the ignition control module by pressing down on the locking tab where it is stamped PUSH, and remove the connector.
  3. Remove the ignition module and the module bracket from the front fender apron.
  4. Unfasten the two ignition module retaining screws, then remove the ignition module form the module bracket.

To install:


0900c1528006b5b4.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: The ignition module on 1994-95 vehicles is mounted on the front fender apron
  1. Install the ignition module onto the module bracket. Tighten the retaining screws to 24-33 inch lbs. (2.7-3.7 Nm).
  2. Position the ignition module and bracket assembly onto the front fender apron. Secure with the retaining bolt and tighten to 35-50 inch lbs. (4-5.6 Nm).
  3. Attach the engine control sensor wiring connector to the ignition module.
  4. Connect the negative battery cable.

Nov 19, 2009 | 1994 Ford Thunderbird

2 Answers

94 taurus wont start after 30 minutes of running until engine cools off


the taurus uses a "thin film" ignition module located on the side of the distributor where it touches the distributor there is a film of heat transfer paste to keep the module cool this paste dries out and, the module heats up and, you have a "no start" until the module cools
the paste is availlible from Ford or, radio shack

Aug 31, 2009 | 1994 Ford Taurus

1 Answer

Engine dies after 20 minutes or so and then will not start again for 10 to 15 min.


Sounds like it could be an ignition module (controls the coil), often when they begin to fail they are fine when cold but die when they get hot. If you do replace it make sure you disconnect the battery first, and that the mounting surface is cleaned first, and that you then put the supplied heatsink paste thinly across the mounting surface before installation.

Oct 20, 2008 | 1997 Dodge Ram 1500 Club Cab

Not finding what you are looking for?
1994 Ford F150 Styleside Supercab Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5516 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...