Question about Cars & Trucks

Open Question

What do trouble code B2A00 mean in a 2006 Chevy impala

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 74945 Answers

SOURCE: How do I program my key for my 2006 Chevy Impala?

Add Duplicate Key (PK3 or PK3+ key)
1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.
Originate New Master Key (PK3 or PK3+ key)

1. Insert new key into ignition cylinder and turn it to the ON (RUN) position.
The security light on the dash will illuminate and stay on for ten minutes.
2. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back to the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
3. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back on the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
4. After the security light has gone off the third time, the key has been programmed
into the vehicle’s computer and will operate the car. It has replaced ALL the
previous electronic key codes and is the ONLY key programmed into the
vehicle’s computer.

Add Duplicate Key (PK3 or PK3+ key)

1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.

Posted on May 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace camshaft postion actuator solenoid 2006 chevy impala


Have any codes ? Chevy Colorado P0017 Case Study Part 1 Doesn't matter if this is a Colorado . Same on impala VVT - variable valve timing .

Jul 02, 2016 | 2006 Chevrolet Chevrolet Impala LT

1 Answer

Code p0011 2006 chevy impala: camshaft position actuator


You can read all about your code here:
http://www.obd-codes.com/p0011

Most likely a P0011 DTC will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.

Jul 10, 2015 | 2006 Chevrolet Impala

1 Answer

Hi I have a 2006 Chevy impala with 360240 miles


You need to reset codes with a scanner if trouble codes have been repaired.

Sep 09, 2014 | 2006 Chevrolet Impala

1 Answer

Check engine light is on for my 2006 Chevy impala lt 3.5 v6 for a mass air leak


Hi Eric: You can drive to AutoZone, unless you are in CA, and they will scan for any trouble codes that may be associated with the illuminated check engine light.

Nov 22, 2012 | 2006 Chevrolet Chevrolet Impala LT

1 Answer

I have a 2006 chevy Impala 3.5 v6 Flex fuel with OBD code po446 what is it and where is it Dennis


this obd2 trouble code table can help you understand the meaning of code.

for p0446, you can try:

Replace Vent valve

Repair open, short, or resistance problem in control circuit

Repair open, or short, or resistance problem in power circuit

Replace PCM

Sep 04, 2011 | 2006 Chevrolet Impala

1 Answer

2009 chevy impala check engine light


Check engine lights can mean a number fo different issues. I would recommend that you have the codes read from the computer and this will determine what causing the light to come. Most auto parts store take code reads for FREE!

Feb 05, 2011 | 2006 Chevrolet Impala

3 Answers

2006 Chevy Impala reduced engine power


best bet is to stop in at a Pep Boys, Autozone, or similar big autoparts seller, and ask for free trouble code scan, which should pinpoint area causing problem. If not obvious by codes, what is necessary to repair the problem code, get back to us with those codes and we will be glad to assist you further. Better this way, takes away the guess work, and saves you money, as well as getting it right the first time.

Dec 12, 2009 | 2006 Chevrolet Impala

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...