Question about Chevrolet Equinox

Open Question

How to reset my hazard lights - Equinox Chevrolet Cars & Trucks

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 07 Subaru Forester hazard lights came on and I cannot cut them back off buy the switch on the steering column how do I get hazard lights cut off


Unless you can isolate the fuse which controls them, and unless that fuse controls only the hazard lights, I do not know.

Nov 12, 2017 | Subaru Cars & Trucks

1 Answer

HAZARD LIGHTS WENT ON TURNED OFF 2002 CAMRY: CAN'T TURN OFF


Sounds like you have a bad hazard light switch

Nov 24, 2016 | 2002 Toyota Camry

1 Answer

When I indicate either way the hazard lights come on instead.


reset the hazard lights by pressing the button again

Oct 31, 2013 | Audi Cars & Trucks

2 Answers

VW CADDY 1.6 2011, HOW TO RESET SERVICE LIGHT


Service 1 oil reset
Ignition off
Hazards on
Press hold right side set button
Switch on ignition
Release set button and press buttons on left
Switch off hazards
Turn engine off
Reset for one.year
In owners manual

Aug 08, 2013 | Cars & Trucks

1 Answer

Reset tire pressure sensor


My work van is a e-series 2011 cargo / work van, the way to reset the tire pressure on it is too push the hazard lights button a few times, may 5 or 6 times pretty quickly when the van is in park and running, the horn will honk and and then you stop pushing the hazard button and wait for a few minutes and the horn will honk agian and the tire pressure light will go out, i dont know if this resets the tires pressure sensor, but the light on the dash goes out, on my van it comes back on after i restart the van , so I am guessing that the sensor on my van is bad. but its worth a shot on your car.

Feb 09, 2012 | Ford E-Series Van Cars & Trucks

1 Answer

Problem: A co-worker has a 1999 Audi A6 Quattro. Her directionals stopped working and she's had to resort to manually moving the switch arm (the hazards work fine, though). Someone on the internet...


i think her problem is the hazard light switch this is how they go when they go wrong the indicators stop working ,their is no magic relay or seting dash lights --- not on such an old car ,the hazards work but no indicators ,they all use the same flasher unit but its all wired through teh hazard light switch ,anyway shes a female and they never use indicators anyway ,only hazards for triple parking outside the hairdresser

Dec 30, 2010 | 1999 Audi A6

1 Answer

Hazard lights won't turn off. Disconnected battery now hazards won't stop.


I see this is an old question, but I'll answer it because I ran into it myself - after hooking the battery up again, hold down the lock button on your little lock/unlock remote. If that doesn't work, hold down the unlock button. I always forget and end up doing one and then the other. In any case, it resets and the hazards should stop flashing!

Dec 22, 2010 | 1997 Subaru Outback

1 Answer

Left front turn signal does not flash. Left rear OK. socket was corroded so I replaced socket. No flash. Checked wires for voltage, only the parking light connection ever gets anything. Front and rear...


Try pushing the Hazard switch on the Column several times and see if it restores the connection. From what I understand about the Multifunction Turn switch is that some of the contacts share connections with the Hazard Button.

The contacts work on a type of derailer setup and when the contacts get dirty or wear, things stop working. Moving the Hazard switch resets the points and springs each time you go in and out of the Hazard setting.

If your brake light is working you know the wires to the light socket from the brake switch are okay. Probably would not hurt to check brake light switch as it shares the common wire. The split between the left turn and right turn signal wire has to occur, yet the opposite brake light will stay on steady while the other side blinks.

Oct 22, 2010 | Ford E-250 Cars & Trucks

2 Answers

No hazard lights


Check the hazard switch and the connector to hazard switch see if u have the power and earth to hazard switch if there is power and earth to switch then replace ur hazard switch its faulty but if there is no power and earth to switch then it has whirring problem

Jun 16, 2009 | 1997 Mitsubishi Mirage

2 Answers

How to reset the computer, if i replaced the break pads myself


you shouldnt have to, if the sensors are installed back correctly, make sure the little copper "u' parts are on the sensor when you put them back in, quite often they fall off witout realising it. if you have done that all ok turn youre hazard lights on & disconnect the battery for about ten minutes. put battery back on & turn hazard lights off. that should drain the stored problem & reset the system. see how you go.

Aug 02, 2008 | 2007 BMW 525xi Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...