Question about 2001 Daewoo Nubira

1 Answer

Where is the pcv valve on 2001 daewoo nubira?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Daewoo Master
  • 20,706 Answers

Great question.
that depends on engine, which engine option is in car.

Posted on Jun 29, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 74 Answers

SOURCE: change alternator on daewoo nubira

first you need to remove the belt . there are only several bolts to remove the alternator . there should be a diagram on the panel by the hood prop rod to show the belt route

Posted on Feb 18, 2009

stevenhurc
  • 450 Answers

SOURCE: my car daewoo nubira 1998 stopd at idle speed and the center luck

these vehicles had a zylux immobiliser fitted at point of entry to Australia others had after market system fitted they didnt actuall build them with these features.you need to go to a dealer to repair or program new remote, have you got a second key remote? this one might still work

Posted on May 28, 2009

alicantecoli
  • 22095 Answers

SOURCE: 2000 Daewoo Nubira camshaft position sensor

on the front under timing belt cover ,back cam ,if its not their then back of head about 3inches along from the gear wheel end

Posted on Sep 11, 2009

  • 1986 Answers

SOURCE: How to scan the 2001 daewoo nubira fault codes.

Your port should be located under the dash on the driver's side near your knee area. The port should be pointing straight down from the dash. The scanner will be plug and play and you shouldn't have to jump and pins for the OBD-II port. As for the codes, there are so many thousands of codes that you can't even guess what codes will be generated from your scan

Posted on Sep 30, 2009

emissionwiz
  • 75117 Answers

SOURCE: how to change the timing belt on a 2001 daewoo

follow these instructions exactly, be sure u get it right or u will bend the engine valves this is an interference engine, if u have a broken belt u most likey have bent valves, about 90% of the time the valves do get bent.
here are the instructions.

Required tools:
13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers
If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.
Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.

To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple.
In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long.
One more item that you may as well replace while you are in there is the cam position sensor if you have not already, as there have been issues with them, and the timing housing has to be opened to get to it

Posted on Apr 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the pcv valve located on 2001 daewoo nubira?


the pvc on most cars is in the valve cover with a hose going to it which is usually about 1/2 to 5/8 easy to find

May 05, 2014 | Cars & Trucks

1 Answer

What are the torque specifications and tightening sequence for cam journal and cylinder head for 2001 daewoo nubira 2.0 :(


  1. The torque settings for the cylinder head bolts on a daewoo ...

    www.answers.com > ... > Categories > Cars & Vehicles > Asian Car i need how much pression (torque) for head daewoo nubira 2001 2.0 ... What is the cylinder head torque specs for a 2001 daewoo nubira 2.0 litre engine and ...

Apr 15, 2011 | 2001 Daewoo Nubira

1 Answer

I heard that 2001 daewoo nubiras were recalled, who can i contact if i believe i have a defective unit?


ok you can check if you have any of the recall problems here http://www.autorecalls.us/aut-04/recalls/2001/daewoo/nubira/78657.html then contact the nearest daewoo dealer to arange repairs. these should be at no expense to you as they are factory faults. hope that helps. let me know how you go.

Feb 04, 2011 | 2001 Daewoo Nubira

1 Answer

Replace spark plugs on a 2001 Daewoo Nubira


daewooautopartspr.com can provide this diagram online. It's free

Apr 27, 2010 | 1999 Daewoo Nubira

2 Answers

Daewoo Nubira hunts on idle revs high in between gear changes


I have a Daewoo nubira estate 2001. When starting the engine it hunts from about 1000 up to 2500 up and down. I have had the air control valve changed twice, the first time it fixed the problem, but the second time it had no effect. Is there any other item that can give this effect and how do I correct it Thanks.

Dec 12, 2009 | Daewoo Nubira Cars & Trucks

1 Answer

My 2000 Daewoo Nubira leaks oil from engine


I would think that if the PCV valve were actually plugged, there may be enough pressure build-up to unseat the thing, which would cause most oil leaking from crankcase pressure to exit via the hole left where the PCV was. Just a guess. How many miles on this Nubira?

Feb 27, 2009 | 2000 Jeep Grand Cherokee

1 Answer

2000 Daewoo Nubira PCV valve location.


Go to your local auto parts store and look for a chiltons or haynes repair manual for your make and model of car. 2000 daewoo nubria. They might already have one open and available for your reference, otherwise its probably $20.00 for one. Do a search online in a forum specifically for daewoos. there might be someone else that has this info available.

Feb 26, 2009 | Ford Ranger Cars & Trucks

Not finding what you are looking for?
2001 Daewoo Nubira Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...