Question about Dodge Intrepid

Open Question

Vauxhall vivaro 2007 with P0340 code, Checked camshaft sensor and they is no wire with a plug to attach to sensor?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: vauxhall vivaro wont start cold

Sounds like a faulty cold start assistor. On top of the engine you will find an aluminium housing with four things that look like glow plugs screwed into it. These 'glow plugs' are only available complete with the housing fron Vauxhall. Approx £70 +
Airbag light is probably a fault with the seatbelt pretensioner.
Check the wiring under the seats for damage or perhaps the plugs have pulled apart.

Posted on Jan 28, 2009

Ad
davesmith_37
  • 94 Answers

SOURCE: P0340 Code Camshaft Position Sensor


The Camshaft Position (CMP) Sensor detects the position of the camshaft in order to identifiy when piston No. 1 is on its compression stroke. The CMP sensor is used for ignition timing in the Ford DIS igntion system, but not in the EDIS igntion system. Both DIS/EDIS use the CMP signal for synchronizing the firing of sequential fuel injectors.

On the 3.0L vulcan engine, the CMP signal is generated by a single Hall-Effect magnetic switch, activated by a single "vane" spinning around by virture of a synchronized shaft which is driven by the camshaft. 

The CMP sensor & synchronizer/shaft are located behind the intake manifold (i.e., back near the firewall on a Ranger) on the top of the cylinder block. If you just need to replace the sensor, it is a simple job of unplugging the electrical connector and removing the screws holding the sensor in place. Here is a sketch of the sensor to give you an idea what to look for:

Posted on Feb 27, 2009

  • 15 Answers

SOURCE: 2002 pt cruiser Camshaft Sensor

change the crankshaft positon sensor in the rear of the engine above the oilfilter. Also check the wiring to this sensor, they have a problem shorting out. You have to change the camshaft and crankshaft sensors at the same time. Make sure you give your car a major tune up. Did you check yor starter?.........runjoe

Posted on Mar 04, 2009

HyeProfile
  • 35 Answers

SOURCE: sensor locations

Here's the diagnostic procedure for DTC code 0340, directly from the service manual:

8f57ac3.jpg
a08cb42.jpg
ce6092c.jpg
b3a9ad5.jpg
e76f3a6.jpg
5a415d6.jpg
f69cd27.jpg

Posted on Aug 05, 2009

  • 753 Answers

SOURCE: 3 codes present on my 2002 Envoy. p0172, p0420, and p0340,

Track the p0340 first camshaft timing is very important and could possibly cayse your other codes,Call your local GMC dealer I think I remember a bulletin about this code.

Posted on Aug 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Code P0340.


camshaft position sensor circuit malfunction---check the connection and wiring around and to the sensor the following link can assist you with the trouble shooting
http://www.obd-codes.com/p0340 P0340 Camshaft Position Sensor Circuit Malfunction http://www.myautorepairadvice.com/p0340.html

Aug 19, 2016 | Cars & Trucks

1 Answer

What are the probable causes of DTC P0340 other than a defective CPS?


Symptoms can include: Hard starting or no start
Rough running / misfiring Loss of engine power Causes
A code P0340 could mean one or more of the following has happened:
a wire or connector in the circuit could be grounded/shorted/broken the camshaft position sensor may have failed the PCM may have failed
there exists an open circuit
the crankshaft position sensor may have failed

Possible Solutions With a P0340 OBD-II trouble code,
diagnosis can be tricky at times. Here are some things to try: Visually inspect all the wiring and connectors in the circuit Check for continuity in the circuit wiring Check the operation (voltage) of the camshaft position sensor Replace the camshaft position sensor as required Check the crankshaft position circuit as well Replace circuit wiring and/or connectors as required Diagnose/replace the PCM as required

Read more at: http://www.obd-codes.com/p0340
Copyright OBD-Codes.com

May 06, 2016 | Nissan Maxima Cars & Trucks

1 Answer

Carnt find the wire with plug to attach to the camshaft sensor on vauxhall vivaro 2.0 cdti


we have pack rats here, and they eat wires to deep in harness.
got rats?
my bud here, RV they eat the air bags 2 times, as $3000 each time.
they cut is comprehensive after 2nd. (ins. goons)

how did the CMP get unplugged,we wait with baited breath>>.......

May 06, 2014 | Cars & Trucks

1 Answer

P0340 vauxhall vivaro


not always cam sensor could be crank sensor if it cranks long and starts it can be crank sensor if it starts right away the cam sensor can cause a missfire as well if you have a pressure switch for oil level it to can cause no start check the oil level if its full it can cause a no start if this model is equipped

May 05, 2014 | Vauxhall Vectra Cars & Trucks

1 Answer

Vauxhall vivaro 2.0 cdti camsahft sensor p0340 fault


top right hand side cam sprocket cover this pic may help

May 05, 2014 | Vauxhall Viscount Cars & Trucks

1 Answer

Where is the wiring with the conection plug for the cam shaft position sensor on vauxhall vivaro 2.0 cdti?


i would say this sensor connector must have got tucked away somewhere after having work done on engine

May 05, 2014 | 2002 Volkswagen Eurovan

3 Answers

What does p0340(pd) code mean


P0340 is

Camshaft Position Sensor Circuit Malfunction
What does that mean?

This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.
FB.init("dd7d9e9681341cde77587bc6a2029f6f"); OBD-Codes.com on Facebook Symptoms

Symptoms can include:

  • Hard starting or no start
  • Rough running / misfiring
  • Loss of engine power
Causes

A code P0340 could mean one or more of the following has happened:

  • a wire or connector in the circuit could be grounded/shorted/broken
  • the camshaft position sensor may have failed
  • the PCM may have failed
  • there exists an open circuit
  • the crankshaft position sensor may have failed
Possible Solutions

With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required

Mar 20, 2011 | 1999 Cadillac Seville

3 Answers

P0340 code. I Changed cam sensor and checked wiring. what else could be wrong? Jeep cherokee, 6 cil


A code P0340 could mean one or more of the following has happened:

•a wire or connector in the circuit could be grounded/shorted/broken
•the camshaft position sensor may have failed
•the PCM may have failed
•there exists an open circuit
•the crankshaft position sensor may have failed

With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

•Visually inspect all the wiring and connectors in the circuit
•Check for continuity in the circuit wiring
•Check the operation (voltage) of the camshaft position sensor
•Replace the camshaft position sensor as required
•Check the crankshaft position circuit as well
•Replace circuit wiring and/or connectors as required
•Diagnose/replace the PCM as required

Feb 20, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Code p0340 need location on 2004 sebring 2.7 v6



P0340 OBD-II Trouble Code
Technical Description
Camshaft Position Sensor Circuit Malfunction


What does that mean? This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.

Symptoms
Symptoms can include:
  • Hard starting or no start
  • Rough running / misfiring
  • Loss of engine power

Causes A code P0340 could mean one or more of the following has happened:
  • a wire or connector in the circuit could be grounded/shorted/broken
  • the camshaft position sensor may have failed
  • the PCM may have failed
  • there exists an open circuit
  • the crankshaft position sensor may have failed

Possible Solutions With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required

Also, the cams/crank are out of alignment, thats why you are getting a cam position code (P0340). For more details about your model, you can visit autozone.com (free register)

Hope helped whit this (remember rated this help) Good luck.

Oct 23, 2009 | 2004 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...