Question about 2005 Chevrolet Silverado

2 Answers

Abs comes on at low speed on dry roads 2004 silverado 4x4 right frount only

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Chevrolet Master
  • 3,854 Answers

One of the sensors has gone bad and needs to be replaced, the other thing to that would also do that is the ABS sensor is dirty or needs to be re gaped to the speed ring on the hub. There was a issue bulletin with your Tahoe on the ABS activating under 8 km/h. Good luck and hope this helps, if not clean out the sensor with brake parts cleaner and check the wire harness and ABS sensor bracket. Re gap the sensor to the speed ring hub. Here is the bulletin. Anti lock Brake (ABS) Activation at Low Speeds (Clean Wheel Speed Sensor Mounting Surface) #03-05-25-007C - (05/16/2006) 2001-2006 Chevrolet Suburban, Tahoe

Posted on Jun 22, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

Joe it is common for the brakes to moan when they wear down and sometimes they will squeak, try replacing the front pads and lubing the shafts on the calipers install anti squeal on the back of the pads, the ABS device would not cause noise as they are just a ring with a magnet and the reluctor ring spins and the magnet detects the spinning of the reluctor ring, they don't even touch and are stationary in place where they are mounted. There is a possibility that the brake fluid is dirty and could cause the abs motor to groan but you would just have to flush the system, When you don't put your foot in it on the brakes it will make some noise even new, I have a 2008 ford ranger that makes the same noise and the brakes are fine. You will have to adjust your braking habits to stop the noise. You can change the pads and that will help but not for long, be sure when you are operating your brakes press firmly on the pedal until you stop. If the brakes make noise after you let up on the pedal then the caliper parts need to be cleaned and lubed, however it is not a safety issue. also Molson02536 has a point as well.

Posted on Jun 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the rear abs sensor located on a 2004 silverado z71 4x4


Usually cars have ABS sensor mounted on the rear right wheel, inside the wheel hub, near the polar disk.

May 07, 2014 | 2004 Chevrolet Silverado 1500 Crew Cab

1 Answer

I have a 2004 silverado error code u1000 ,my 4x4 does'nt work and my abs and brake light is on


sounds like a wheel speed sensor.
or worst case a abs module.
is 4x4 electronic selection?

Jan 05, 2014 | 2004 Chevrolet Silverado 1500 Crew Cab

1 Answer

I HAVE A 2004 SILVERADO AND ERROR CODE U1000 COMES ON 4X4 DOES`NT WORK ABS AND BRAKE LIGHT IS ON


  1. abs and brake light means u need fluid or u have a leak
  2. then 4x4 works not all trucks but 50% are like that

Jan 05, 2014 | 2004 Chevrolet Silverado 1500 Crew Cab

1 Answer

2005 Kia Sorento - on dry pavement going forward in 4 wheel drive at slow speed turning left the rear wheel driver side seems to be trying to go reverse, can hear is catching or locking on the road,...


you shouldnt use 4x4 on dry road its made for pulling or snow mud etc type situations if you feel its ok then check tire size are they all the same size tires and the pressure all the same if you dont have a check eng light on then there is nothing wrong with the 4x4 but dont forget all wheel drive works with abs tcm if one wheel spins faster or slower then the rest it puts on the abs to slow it down or the trans shifts up to speed it up so there are a few things to check

Jun 21, 2011 | Kia Sorento LX Cars & Trucks

1 Answer

2003 F150 4x4 ABS activates at low speed approaching full stop in dry conditions; no ABS light on.


only when they is fault in any abs sensor abs light will light on that mean no problem

Apr 05, 2011 | 2004 Ford F150

1 Answer

Brake pedal a.b.s pulsation at slow speeds on dry road.It wont do it all the time. It is on a 2000 chevy silverado 1500 4x4. I can hear the abs kick in when this happens.


You may see the abs light come on in your dash. I would plug a OBD II reader in and retrieve the codes.
I would say you either have a sensor that has gone bad or possibly a wire is shorting.
You can see the wheel sensor if you turn your wheels, and look down by the wheel hub bearing.
You can here the abs go whrrrrrrrr, when you step on the brake, and your braking flucuating.
Please let me know what you find.

Feb 11, 2010 | 2000 Chevrolet Silverado

1 Answer

Truck not stoping and anti brake is working.


dosen't stop at all or just slow?, if the abs is working then you should feel the pulseing in the brake pedal just before tire lock-up, the tires will not lock-up with abs fully funtioning unless all four tires or two are in lock-up depending on the abs application, if abs fails it reverts it self to regular braking ability, hope this helps

Sep 14, 2009 | 2004 Chevrolet Silverado

1 Answer

2001 silverado 4x4 abs brake keeps coming on


in these trucks if the front abs activates at low speeds it is normally because of the wheel speed sensors in the front hubs. easy fix is to remove wheel speed sensor from wheel bearing. clean and file cast surface of bearing to allow sensor to move closer to internal reluctor ring. what happens is over time the casting rusts and creates a larger gap. please rate if this works.

Dec 04, 2008 | 1999 Chevrolet Silverado 1500

2 Answers

Antilock brake system engages on low speed stops on dry pavement on my 2004 Silverado.


The most likely cause is rust buildup under wheel speed sensors causing them to dislodge(lift up) from front hubs and read incorrectly. If recall has been performed to fix this problem...You may have to replace the appropriate hub in order to stop the ABS activation at low speeds. Let me know if i can help more.

Nov 03, 2008 | 2004 Chevrolet Silverado

Not finding what you are looking for?
2005 Chevrolet Silverado Logo

2,797 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8274 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...