Question about 1999 Ford Ranger SuperCab

1 Answer

The abs on my 2003 ranger dosn't work right

Every so often when i push on the break pedal the engine revs up.It's did this since it was new.The dealer said it coudn't find the problem and it didn't do it for them had it in 3 times. now my breaks are locking up when i push hard on pedal,

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 60 Answers

It sounds like there is a problem with the brake booster. they use engine vacuum to operate and that would make it rev when you brake

Posted on Jun 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

'03 2.5L Ford Ranger Standard Trans, Engine at times won't turn over, does not click, battery is fully charged.


Neutral safety switch on the clutch pedal may be going out. Its a $15 fix. It tells the computer if the clutch is engaged. If it goes out its like trying to start with out pushing in the clutch, wont turn over at all. Hope this helps.

Oct 16, 2012 | 2003 Ford Ranger Regular Cab

1 Answer

Car want stay running


Has any,one worked on the car recently?It sounds like you have a vaccum hose broken or just leaking real bad.More info on how does it run when you have the gas pedal down,,is it running rough,missing,popping.This will help us getting to the bottom of your problem.

Jan 02, 2012 | 2001 Ford Taurus

1 Answer

My 2003 neon stalls as soon as I take my foot off of the accelerator pedal or slow down it just dies....i put it in neutral and rev the engine and it revs to 4000 rpm and just breaks up....i just changed...


you may have a dirty fuel filter or the throttle plate may need cleaning.the throttle plate is the valve that moves in the intake when you move the gas pedal.if they get too dirty they cause a restriction in the intake and cause the car to stall.it also could be a tps sensor problem but this should put the check engine light on but not always.the breaking up of the motor when you rev it to 4000 rpm`s is the rev limiter in the computer that shuts down the firing of the plugs and injecotrs so you don`t cause damage to the motor when there is no load on it.

Sep 17, 2011 | 2003 Dodge Neon

1 Answer

My 2004 prius abs and brake light came on and the the brakes became very hard and constant beeeep noise, so i would shut the car off and pump the breaks and it would work fine so i decided to bleed the...


well, a hard firm pedal, usually indicates a bad brake booster or a vacuum leak to booster or the vacuum check valve, on booster. TO TEST BRAKE BOOSTER; pump brakes several times with engine off to deplete stored vacuum. turn on engine with pushing slightly on pedal. you should feel the pedal fade away a bit and then become firm, but not hard. if you feel nothing at the pedal when engine starts the booster is at fault. good-luck !!

Feb 03, 2011 | 2003 Toyota Prius

2 Answers

My break pedal is hard to push & i can here air when the peadel is pushed into stop, and is this connected to the abs if there is one on my model.. thanks for your help. would this be the brake...


not sue u have abs on that model
more than likely break booster
best way to check booster is stop truck pump pedal a few time then put your foot on brake pedal and push down this is with truck stopped ,keeping pedal pushed start engine brake pedal should move down more if booster is working check all pipes tp booster

Sep 29, 2010 | 1995 Toyota 4Runner

2 Answers

I have a 88 S-10 with 4 wheel disk breaks,I have a new master cylinder and proportion valve,and all new break lines, I am trying to bleed the breaks but cant get a good pedal.my Q is how much pedal should...


Power and manual have the same equivalent
Power is just easier to apply than manual
To BLEED brakes properly and this is the only way which will be correct is to start at the furthest point and work your way to the closest point upon completion. If not done this way air will be still in the lines

May 29, 2010 | 1988 Chevrolet S-10

1 Answer

2003 Ford Ranger Pickup traveling down the road


Is there somthing hitting the gas pedal, like the floor mat? Or maybe something under the dash came loose and is getting caught under the brake pedal and pushing on the gas. Put the shifter in neutral if you get into a situation where going to hit something or someone. The engine has a rev limiter, to prevent it from over reving.

Feb 10, 2010 | 2003 Ford Ranger Regular Cab

1 Answer

2003 ford ranger There is no resistance in the


right old trick ,with assistant ,who has to be pretty and blonde ,get assistant to push and hold pedal down ,then you go underneath and using a bar wedged in somewhere push the actuator arm in so the slave closes,as you push it in open bleed nut,then assistant lets the pedal up and repeat ,push pedal down and holds it down whilst you force the arm back with bleed valve open ,close valve and blonde assistant releases the pedal.easy when you know how

Jan 17, 2010 | 2003 Ford Ranger Regular Cab

1 Answer

ABS LIGHT AND BRAKE LIGHT COMES ON


please replace the rear brake shoes with brand new, not relined, purchased from the dealer. Also, replace all the rear brake hardware, springs, etc.

Jul 17, 2009 | 1993 Plymouth Voyager

1 Answer

Accelorator problems on ford ranger


Sounds like Throttle position sensor faulty.

Jun 21, 2009 | 2003 Ford Ranger Regular Cab

Not finding what you are looking for?
1999 Ford Ranger SuperCab Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...