Question about 2010 Cadillac SRX

Open Question

How do you change the low headlamp beam on a 2010 Cadillac SRX?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: Replacing front turn signal bulb on 2006 Cadillac SRX

wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.

Posted on Jan 25, 2009

Ad

SOURCE: low beam head lights won't work

Check your relay switches under the hood fuse box. They should be a light grey from factory, they are about 1 x 1" in size and there are a few in there. Pull one out at a time and if they look brownish or yellowing replace. Go to Napa or Auto Zone for $15.99 a peice that most likely will fix it.

Posted on Mar 24, 2009

techbuster
  • 5081 Answers

SOURCE: rear liscese plate bulbs on 05 cadillac srx

First you have to take out the one and only screw in the rear hatch door - it's where the hand pull down is you use to close the hatch.
Then you have to pop all the plastic clips all the way around the plastic door panel, trying not to pull them out from the frame . If you do pull out the white plastic plugs from the frame you better make certain you take them off the plastic housing and insert them back into their frame holes - or you will never get the housing back on.

Once you have the housing loose disconnect the inside tail gate light wire to remove the whole thing. Then you have to remove 7 to 8 nuts from the back of entire License plate, back up bulb housing using a deep socket to get in there. Work it loose from the rear of the car and it will come out just enough to work on the lights.
This is tricky since the screw mounts don't give you much room to work with.

Once you have the license plate and back up bulb frame loose you will see the two housings for the license plate bulbs on top.

Slide out the license plate bulb lens and twist the bulb connection to remove the bulbs.
Replace both of them - you don't want to do this again in a month when the other one blows.

OPTIONAL:
Once you take out the bulbs you might see that the housing is melted where the bulb wanted to burn through. Drill two small holes one is each end of the housing before I put everything back together to release some of the heat.


Reverse the whole process to put everything back together. It's not easy.
Make sure you insert the cables through the opening for the hatch handle or it will kink and not work properly.

The bulbs come in a two pack of cost $4.95 .

Posted on Nov 24, 2009

  • 1 Answer

SOURCE: Changing fuel filter on 2004 Cadillac SRX

If you go to the auto parts store they should have a fuel line disconnect tool that has a 5/16ths end an a 3/8ths end. The tool is shaped like an X. Before you start you need to pull the fuel pump fuse under the front of the REAR passenger side seat while the car is running and let it stall. it will release the built up pressure. This is important unless you want gas to spray every where. Then take the tool and start with the end of the filter with two lines. Place the appropriate end of the tool over the smallest inlet, push the tool in then pull the line towards the filter and then push the line away and it should disconnect. Do the same with line above. Then you can use the two appropriate size wrenches to disconnect the outlet end. reconnecting the new filter is simple just make sure your quick connect lines click in all the way and you tighten the outlet line well, I think its like 22 or 25 ft/lbs.

Posted on Dec 15, 2009

  • 396 Answers

SOURCE: Wiring diagram for 2009 Cadillac SRX

Try your dealer parts counter.

Posted on Jan 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Saturn aura wont start after trying to put rt.low lowbeam replacement


On the inside of the lid is a diagram .
The headlamps may be turned ON 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the AUTO position, for automatic lamp control (ALC). During ALC, the headlamps will be OFF in daylight conditions, or low beam operation in low light conditions. Battery positive voltage is supplied to the low beam relay and the high beam relay in the underhood fuse block. When low beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the low beam relay. This activates the relay and the relay supplies voltage to the left hand low beam headlamp through the LH LOW BEAM fuse and to the right hand low beam headlamp through the RH LOW BEAM fuse. Ground for the left hand low beam headlamp is provided at G101. Ground for the right hand low beam headlamp is provided at G102. When high beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the high beam relay. This activates the relay and the relay supplies voltage to the left hand high beam headlamp through the LH HIGH BEAM fuse and to the right hand high beam headlamp through the RH HIGH BEAM fuse. Ground for the left hand high beam headlamp is provided at G101. Ground for the right hand high beam headlamp is provided at G102.

Aug 14, 2017 | Saturn Cars & Trucks

2 Answers

Why is there water in my head lights in my Cadillac 2010 srx


Water buildup can be due to humidity and condensation. This is a common problem on the Cadillac SRX 2010-2011(at least). The replacement can cost about $1,500 USD through a dealership.

Aug 10, 2017 | Cadillac Cars & Trucks

1 Answer

HOW TO CHANGE THE FUEL PUMP ON 2010 SRX 4 DR. V6


did you test or are you guessing ? The fuel pump relay allows the ECM to energize the fuel pump. The ECM enables the fuel pump whenever the crankshaft position (CKP) sensor pulses are detected. GM Fuel Pump Relay Testing

Dec 01, 2016 | 2010 Cadillac SRX AWD

1 Answer

2010 impala high beams do not come on, light on dash comes on, replaced bulbs still don't work, checked all fuses, look good


High Beam Headlamp Operation
Battery voltage is applied at all times to the coil and switch sides of the HIGH BEAM PCB Relay located in the underhood fuse block. When the headlamp dimmer switch is placed in the high beam position, the headlamp dimmer switch signal circuit to the BCM is pulled low signaling the headlamp high beam request. In response to this signal, the BCM applies ground through the high beam relay control circuit energizing the high beam relay. With the high beam relay energized, battery voltage is applied through the switch side of the relay, the left and right high beam fuses, and the high beam supply voltage circuits illuminating the high beam headlamps. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) requesting the IPC to illuminate the high beam indicator. Ground for the left headlamp is provided at G101 and the right headlamp at G100.

Nov 23, 2016 | 2010 Chevrolet Impala

1 Answer

Two questions how do you change a low beam lightbulb in a cadillac srx 2005 and why in early morning starts does the same car hesitate to pull away?


1. Remove front wheel well front half splash guard, each side. There are about 2 screws and the guard pulls forward to seperate from the rear half.
2. After removing the splash guard, you can access one screw that attaches the front fascia, each side.
3. Then about 6 plastic push pin type screws along the bottom, underneath.
4. About 5 push pin type screws on the top.
5. Fascia should then simply pull forward. It is a bit bulky and an extra pair of hands is helpful.
6. Then there are 3 screws to remove the headlamp assembly. Unclip the wiring harness.
7. Then 4 screws to remove the bulb access cover plate.

Dec 24, 2010 | 2005 Cadillac SRX

1 Answer

How to change low beam headlights on srx. Ed


give these websites a try www.alldatadiy.com and www.autozone.com if you have a autozone or any parts store near you and buy the blub from them they will help you install it for free wish you the best of luck Michigan Man.

Feb 23, 2010 | 2004 Cadillac SRX

1 Answer

How to aim the headlamps on a 1999 Cadillac Catera?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 02, 2009 | 1999 Cadillac Catera

1 Answer

How to change front headlamp bulb? Low beam


  1. Open the hood.
  2. Remove Grille.
  3. Remove the 2 retainers on back of headlamp assembly and remove the headlamp from the sheet metal panel.
  4. Remove the access cover from the rear of the headlamp.
  5. Disconnect the electrical connector from the socket.
  6. Rotate the bulb and socket counter clockwise in order to remove the bulb and socket from the housing.
  7. Disconnect the electrical connector from the socket.
  8. Remove the bulb and socket from the headlamp.
Installation Procedure Important: • Replace a high beam bulb with another high beam bulb. The high beam bulb has a black socket. • Replace a low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a grey socket.

Oct 14, 2009 | 2002 Chevrolet TrailBlazer

Not finding what you are looking for?
2010 Cadillac SRX Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...