Location of a camshaft sensor on a 1999 chryler concord 2.7 L

No one here is going to be able to give you VIN Based information on any vehicle. If you want that, take a month subscription to AllData,com, or ask on JustAnswer.com.

Not sure where you are getting 2 or 3 different answers', but on this site, you will be shown SUGGESTED Answers, and they are often wrong and will show you ANYTHING that mentions Isuzu and camshaft..

Most of the information online leads to to Isuzu Rodeo, this search query forces it to show 'Trooper'. The fly in the ointment is that there are 2 engines.

https://www.google.com/search?q=1999+3.5+isuzu+%22trooper%22+camshaft+position+sensor+location&tbm=isch&ved=2ahUKEwj5vbf96_32AhV6sHIEHV4HAx8Q2-cCegQIABAA&oq=1999+3.5+isuzu+%22trooper%22+camshaft+position+sensor+location&gs_lcp=CgNpbWcQAzIHCCMQ7wMQJ1CdIlikPWDfRWgAcAB4AIABcIgBvQKSAQMxLjKYAQCgAQGqAQtnd3Mtd2l6LWltZ8ABAQ&sclient=img&ei=hLFMYvnrBfrgytMP3o6M-AE&rlz=1C1QJDB_enCA643CA644

..

Do you have your owners manual? If so it will be located in there. The next thing you could do is disconnect the fuel pump from power to have no fuel.

Do you have a dimmer switch for interior lights and dash lights that is turned all the way on? You may also be able to turn them all the way off. My chrysler is a van and the dimmer switch is a wheel that rolls vertically.

• Torque the bolts in the sequence listed below for the 2.7

1. Bolts 1 through 8 torque to 35 foot lbs.
2. Bolts 1 through 8 torque to 55 foot lbs.
3. Bolts 1 through 8 torque to plus 90 degree turn using a torque angle meter.
4. Bolts 9 through 11 torque to 21 foot lbs.

• If you have any comments please feel free to leave them here.
• Hope this helps and thank you for using FixYa.

Regards, Tony

This is on a 2.7L V6...Is mounted in the front of the timing case cover...

Hi!!
THE OIL PRESSURE SHOULD BE CHECKED REMOVING THE OIL PRESSURE SENSOR AND INSERTING A MANUAL OIL PRESSURE GAUGE. AFTER TEST, USE TEFLON TAPE TO REINSTALL THE OIL PRESSURE SENSOR
5 PSI. MIN AT IDLE 45 TO 105 PSI. AT 3,000 RPM
A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Go to your local auto parts store and purchase a Haynes Manual # 38026 which covers 1997 through 2003 Malibu's and it will give you step by step instructions as well as diagrams and photos of the procedure.Most Camshaft Sensors are located in the distributor cap under the rotor button. They generally have three to four wires dependent on the type of camshaft sensor is employed, but insofar as setting it or "gapping" it like you may have to do with a crankshaft sensor, this is a simple remove and replace. Depending upon your engine, look at the distributor and if you see under the distributor cap a small ribbon wire (like in computers), it will always be attached closely to a plug on the wiring harness. The Haynes Manual will even give you the wiring gauge, color and location in the back of the manual whereas Chilton never caught on to putting wiring diagrams in their books. You'll find the Camshaft Sensor in section 14, Emissions insofar as how to test and/or replace it.

"00 Buck"

Change your Crankshaft position sensor, or your camshaft position sensor. Same thing happened on my car about 3 months ago.

Should be in the manifold on the back side closest to the firewall.

Check the cranshaft position sensor located under the timing cover. Also check the camshaft sensor located near the camshaft.