Question about Cars & Trucks

Open Question

Nissan juke drive belt tensioner removal - Cars & Trucks

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jturcotte
  • 8206 Answers

SOURCE: 2002 KIA SPORTAGE. REPLACING FAN BELT NEED RO

Hi, there are up to three belts if you have A/C. Each belt has a tensioning system. Diagrams and instructions from autozone.com are paste below. Please let me know if you have any questions, and thanks for using FixYa.

A/C belt:
jturcotte_1115.gif



Alternator and fan belt:
jturcotte_1116.gif
top view of generator belt adjusting bolt C:
jturcotte_1117.gif



Power steering belt:
jturcotte_1118.gif


Removal & Installation

A/C Compressor Belt

  1. Disconnect the negative battery cable.
  2. Loosen locknut (A).
  3. Remove the drive belt.

To install:
  1. Properly route drive belt around the pulleys.
  2. Adjust bolt (B) until belt tension is 22 ft. lbs. (30 Nm)when measured at deflection point shown.
  3. Retighten locknut (A) to 24 ft. lbs. (32 Nm).
  4. Connect the negative battery cable.

Alternator Belt
  1. Disconnect the negative battery cable.
  2. Remove the A/C belt.
  3. Loosen mounting bolts (A) and (B) from the back side of the alternator.
  4. Loosen adjustment bolt (C) and remove the drive belt.

To install:
  1. Properly route drive belt around the pulleys.
  2. Adjust bolt (C) until belt tension is 22 ft. lbs. (30 Nm)when measured at deflection point shown.
  3. Retighten locknut (A) to 16 ft. lbs. (22 Nm)and locknut (B) to 32 ft. lbs. (43 Nm).
  4. Reinstall the A/C drive belt.
  5. Connect the negative battery cable.

Power Steering Pump Belt
  1. Disconnect the negative battery cable.
  2. Remove the A/C and alternator drive belts for access.
  3. Loosen mounting lock bolt (A) and mounting bolt (B).
  4. With tension released removed the belt.

To install:
  1. Properly route drive belt around the pulleys.
  2. Carefully pry on the power steering pump using a suitable lever. Adjust belt tension is 22 ft. lbs. (30 Nm) when measured at deflection point shown.
  3. Retighten bolts (A) and (B) to 31 ft. lbs. (42 Nm).
  4. Reinstall the A/C and alternator drive belts.
  5. Connect the negative battery cable.

Posted on Feb 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing tensioner assembly


images for 2008 Nissan Versa Removing tensioner

    how do you remove tension off surpentine belt tensioner - Nissan Forum

    www.nissanforums.com/.../151350-how-do-you-remove-tension-off.htm...

    Feb 20, 2009 - 4 posts - ‎2 authors
    2008+ Nissan Rogue ... QR25 2.5L Engine Engine Discussion: 2002+ Sentra SE-R and SpecV ... how do you remove tension off surpentine belt tensioner ... changed these before, but which way do you turn the tensioner, how ... Replacing the Water Pump on a '04-'08 Maxima *DIY*
    1 post
    Aug 31, 2011
    Belt noise: replace idler pulley? - GA16DE
    8 posts
    Sep 16, 2008
    Step by step instructions -Upper Timing Chain Tensioner
    15 posts
    Dec 8, 2007
    Idler Pulley Bearing Replacement Info
    5 posts
    May 16, 2003
    More results from www.nissanforums.com

    Nissan Versa Tensioner Pulley Issue (1/1) - EricTheCarGuy ...

    www.ericthecarguy.com/.../50669-nissan-versa-tensioner-pulley-issue
    Nissan Versa Tensioner Pulley Issue 1 year 7 months ago #94552 ... for a 50 Torx to be used to remove the entire tensioner pulley assembly but all of my 50Trx

    How to Replace serpentine belt 2008 Nissan Altima ...

    ? 11:29
    https://www.youtube.com/watch?v=5NchA85pnAE
    Jul 2, 2014 - Uploaded by nivekoch
    How to Replace serpentine belt 2008 Nissan Altima In this video i'll be going ... 2005 Nissan Altima 2.5L serpentine belt tensionerreplacement ...

Dec 16, 2015 | 2008 Nissan Versa

1 Answer

How to replace a serpentine belt on a nissan 2007 2.5 s altima


Video Tutorial:
https://youtu.be/h4qGOJ5PpSw

The easiest way to replace serpentine \ drive V belt on 2007-2012 Nissan Altima 2.5L 4 cylinders engine:
- remove front wheel on passenger side
- remove plastic splash cover
- user 14mm offset wrench to turn belt auto-tensioner in clockwise direction
- block auto-tensioner from moving using locking mechanism right above the auto-tensioner pulley
- slide the belt off the smooth non-grooved water pump pulley first
and then take the belt completely out
- when installing a new serpentine belt, first hook it onto all pulleys except for water pump pulley. Hook it onto the water pump pulley last
- make sure the new belt is hooked up properly onto all of the pulleys
- unlock the auto-tensioner
Original OEM Part #:
Amazon com OEM 11720 JA00B Nissan Altima Serpentine Belt
Follow this diagram to route the new belt on 2.5L engine:

replace-serpentine-belt-nissan-2007-2-5-02rhvdv200sh3oinuqbnuvnv-2-2.png

Jan 04, 2013 | 2007 Nissan Sentra 2.0 SL Sedan

1 Answer

2009 nissan altima is making a noise ...i think its the tension. has anyone ever heard of that?


older model altima need drive belt tension adjustment at 7500 miles intervals, the new models altimas has a automatic belt tensioner.i you hear noises belt tensioner could be failing.or could have leaking coolant getting on drive belt due to water pump gasket leaking or pump leaking.or alternator power steering pump could be failing many things will cause drive belt to make high squeak noises.

Oct 09, 2012 | 2005 Nissan Altima

1 Answer

How to change belt


there is a tensioner on the motor that keeps the belt tight on the arm of the tensioner there is a half inch squre hole insert an half inch drive ratchit take the tension of the belt and **** it off the pully remove the belt and install new one if you dont have a diagram of the belt routing on a peise of paper draw the routing before removal

Jun 09, 2012 | 2005 Nissan Pickup Navara

1 Answer

97 nissan maxima replace power steering belt


Easy to do, but also easy to do wrong.

1. Find the belt.
2. Find the belt tensioner.
3. Find the belt tensioner adjuster screw.
4. Loosen the adjustment screw, and slack the belt.
5. Remove the belt.
6. Replace the belt.
7. Tension the belt using the adjustment on the belt tension adjuster.
8. Drive around and steer, easily.

Enjoy.

-Jackson
http://urbanscooters.com/

Oct 11, 2010 | 1997 Nissan Maxima

1 Answer

Nissan altima 2003 how to change engine belt


TO REPLACE DRIVE BELT YOU LOOSEN DRIVE BELT ADJUSTMENT BOLT SLIP THE BELT OFF THE CRANKSHAFT PULLEY AND REMOVE IT. IF YOU GOT A 2.5L ENGINE YOU HAVE TO ROTATE THE BELT TENSIONER TO RELEASE TENSION ON THE SERPENTINE DRIVEBELT.YOU NEED A HAYNES MANUAL.IT WILL SHOW AND TELL YOU HOW TO ADJUST DRIVE BELT AND MEASURE THE DRIVE BELT DEFLECTION USING A STRAIGHT EDGE RULER.

Nov 08, 2009 | 1995 Nissan Altima

1 Answer

How to change 1999 nussan quest ac belt


http://groups.yahoo.com/group/villagerquest/

Belt —A/C Removal
  1. Remove the A/C compressor drive belt.
    1. Loosen the A/C compressor drive belt pulley tensioner bolt.
    1. Loosen the A/C compressor drive belt idler pulley adjustment bolt.
40f6b66.gifInstallation
  1. sxv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Incorrect drive belt installation will cause drive belt failure.
    NOTE: Inspect the pulleys for warping or abnormal wear.
    NOTE: Make sure drive belt is properly installed on each pulley.
    To install, reverse the removal procedure.
    • Adjust the A/C compressor drive belt. For additional information, refer to Belt Adjustment—A/C .

Aug 10, 2009 | 1995 Nissan Quest

1 Answer

How do i REMOVE AND REPLACE THE ALTERNATOR ON MY 95 NISSAN MAXIMA?


TURN OFF RADIO TO KEEP FROM LOSING RADIO CODE.THEN YOU REMOVE NEGATIVE BATTERY CABLE.DISCONNECT THE 2 LEAD WIRES AND HARNESS CONECTOR FROM ALTERNATOR LOOSEN THE DRIVE BELT ADJUSTING BOLT AND REMOVE THE BELT. UNSCREW THE ALTERNATOR ATTACHING BOLTS AND REMOVE THE ALTERNATOR FROM VECHICLE.VISA VERSA PUT EVERY THING BACK.AND ADJUST ALTERNATOR BELT TENSION.WARNING DONT PUT TOO MUCH TENSION ON BELT.BECAUSE YOU WILL DAMAGE ALTERNATOR PULLEY BEARING.

Aug 01, 2009 | 1995 Nissan Maxima

1 Answer

I have a 2001 nissan sentra and it needs a new alternator. i can't figure out how to get the last bolt out. do i have to remove the fan? also, i need pointers on getting the belt back on tightly. thanks....


  • Disconnect and label the wiring harness connections to the alternator (Painters Masking tape works very well for labeling Automotive wiring).
  • Loosen the alternator pivot bolt.
  • Remove the bolt that attaches the alternator to the adjustment arm.
  • Rotate the alternator to loosen the drive belt and disengage the belt from the pulley. Be careful that any spacers that are used in mounting are kept with their original bolts. This will make correct reinstallation much easier.
  • While supporting the alternator remove the pivot bolt.
  • Remove the alternator from the vehicle.
To reinstall the alternator, reverse the removal procedure.
To adjust the belt tension, leave the pivot and adjusting arms loose. Look up the belt tension specification for the vehicle you are working on. Using a belt tension gauge on the belt apply pressure to the alternator until the correct belt tension registers on the gauge and tighten the mounting and adjustment bolts to the specified torque specification.
CAUTION Over tightening of the alternator drive belt will cause the unit to whine and premature failure of the alternator drive end bearing, the water pump or the engine crankshaft.

Jan 12, 2009 | 2001 Nissan Sentra

1 Answer

Change drive belt //


check this out 02bdcd0.jpg
loosen the the two bolts (show on the figure above) first
loosen also the bolt used for adjusting tension.
remove the old worn-out belt.
place the new belt (you may need to loosen further the tension adjusting bolt)
when belt is properly place, tighten it enough the tension adjusting bolt,
(not too tight, but not too loose) press the belt to ensure its not too loose!
When belt tightness is enough, tighten the the other lower one of the two bolt then the lastly tighten the pivot bolt.
gookluck!!!!



Oct 31, 2008 | 2002 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

257 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...