Question about 1998 Chrysler Sebring

Open Question

Where is turn signal flasher on 1998 chrysler sebring

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: turn signals work intermittenly

I have a 99 Chrysler 300 M, my turn signals aren't working. Tried the fuse, was told there is a relay somewhere that controls the turn signals. Please help

Posted on Jun 10, 2009

Ad
co7196
  • 3433 Answers

SOURCE: Where is the starter located on a 1998 chrysler sebring coupe

Follow the +cable from the battery. The starter is on the other end.

Posted on Oct 21, 2009

  • 1 Answer

SOURCE: CHRYSLER town and country mini van turn signal/flasher

I have a 2005 Chrysler T&C. The turn signal would not work at all or activate incorrect side. The switch is easy to remove as described by dukecityman.

Once the switch is of, it has four screws holding it together.I took this apart to find that there was a circuit-board which was contaminated with dirt. wiped it of, put it back together, working fine.

If you take it apart use caution. there are parts on the "top" which will fall out. ( they go right back in) The circuit-board is on the "bottom" half. You really only need to take this part off. (less moving parts)

Your going to replace it anyway, whats the harm?

Posted on Jan 28, 2010

  • 506 Answers

SOURCE: the turn signal or flashers don't work, where is

Check the turn signal/hazard relay in the engine compartment.

Posted on Feb 17, 2010

joshnaz
  • 186 Answers

SOURCE: whats the deck light mean on a 1998 chrysler

Your deck light is the rear trunk lid light.

Posted on Mar 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

LXI. how do I replace flasher?


The Flasher is located: Behind A/C and heater control panel, in center console.

Flashers

Print
REPLACEMENT

Flashers are located either on the bottom of the fuse block or on a module under the dashboard. They are replaced by simply pulling them straight out. Note that the prongs are arranged in such a way that the flasher must be properly oriented before attempting to install it. Turn the flasher until the orientation of the prongs is correct and simply push it firmly in until the prongs are fully engaged.clink on link to see what flasher look's like.
http://www.autozone.com/electrical-and-lighting/turn-signal-flasher/novita-turn-signal-flasher/chrysler/sebring/1998/4-cylinders-y-2-0l-mfi-dohc/193143_0_7283

Aug 15, 2015 | 1997 Chrysler Sebring

2 Answers

Turn signal


Flasher

1997 Chrysler Sebring 2.5L MFI 6cyl

The Flasher is located:

Behind A/C and heater control panel, in center console

Dec 09, 2013 | 1997 Chrysler Sebring

1 Answer

1997 chrysler sebring emergency flashers work but turn signals do not


It is caused by either a bad multifunction (turn signal) switch or a bad combination flasher. With this particular vehicle, the flasher is an integral part of the multifunction switch. So, it can only be repaired by replacing the multifunction switch for either case.

Apr 28, 2012 | 1997 Chrysler Sebring

2 Answers

I need to find where to replace the flasher on my chrysler sebring 1997 lxi. the blinkers arent working and the guy at the auto shop said it was under the dash but i dont see it


Many newer cars have a cover over the fuse panels, look for a small "door" that you can remove to gain access. The owners manual may give you a better indication.

Jan 05, 2010 | 1997 Chrysler Sebring

3 Answers

Blinker stopped working, but the hazard lights still work - I think it's a blown fuse but how and where do I fix the fuse


There is 2 different flashers. One flasher for the turn signals and one flasher for the hazards. If you turn on the turn signals and the turn indicator on the dash lights up but doesn't blink, then most likely it is the turn signal flasher that is bad. Good luck.

May 29, 2009 | 1998 Chrysler Sebring

1 Answer

WHERE IS TURN SIGNAL FLASHER LOCATED ON A 2000 Chrysler Sebing


your turn signal flasher is located on the drivers side in the dash (Explaination) open the driver side door and look on the dash wherethe door closes against it and there is a little panel where your fuses go it should be in there.

Jul 12, 2008 | 2000 Chrysler Sebring

Not finding what you are looking for?
1998 Chrysler Sebring Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...