Question about Cars & Trucks

Open Question

Windsor model 77a


Posted by Anonymous on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Can you replace a 4.6 with a 5.0 in a 2003 mountaineer.

i would be very careful about changing these engines as they are from different series model , the 5ltr 1st gen , 4.6 ltr 2nd gen ,the 1st gen used 3 different chassis the 2nd gen only 1 so there may be a mismatch with the mountings , pipe routing etc, the 5ltr is a 'windsor v8 ' which will take up more room in the engine compartment and you have to be certain that the windsor v8 comes from a mountaineer as they were used in other vehicle's and will have differences , but if you like a challenge and don't mind doing a bit of research go for it , but don't expect it to just drop in and all will be in the right place first time ,keep me posted cheers steve

Jun 10, 2014 | Cars & Trucks

1 Answer

351 windsor

You can tell by looks or by the VIN number if the engine is original.
The fifth digit could be H or Q. H is for the Windsor engine and Q is for Cleveland. The Windsor looks like an ordinary 289 or 302 engine, the Cleveland is a big head 400 version. I don't think they used a 4bbl Windsor but they did use a 2bbl Cleveland so that is not a good example.

Jan 19, 2014 | Cars & Trucks

1 Answer

What degrees do you set a 289 windsor

6 degrees before top dead center. you can go up to 8 degrees if you want more performance. But fuel economy will suffer.

Apr 12, 2013 | Ford Cars & Trucks

1 Answer

Need instruction manual for a vintage windsor pressure canner

I'm sorry but I believe you have this posted in the wrong product category? Please re-post the question in the proper category if this is the case, otherwise you have my apologies. This is the car and truck problem category

Aug 06, 2012 | Cars & Trucks

1 Answer

Could i replace my 351 windsor with a 302 in 1991 bronco

what are you going to do with the old 351 windsor does it run i happen to be looking for one

May 24, 2012 | 1991 Ford Bronco

1 Answer

Ford 351 windsor engine diagram

ford-351-windsor-engine-diagram-p05qnqdskqjeezv3eiltmave-1-0.jpg Here's a mechanical blow-up of an 80's 351w engine.

ford-351-windsor-engine-diagram-p05qnqdskqjeezv3eiltmave-1-2.jpg and the firing order layout.
hope this helps...

Jun 23, 2010 | 1991 Ford Bronco

1 Answer

I was changing my head gaskets on a 2001 windsor 5.4l triton and I forgot to put the cam lock on the cam before removing the chian. How can I determine the right position of the cams now?

Ok I spent half an hour typing in detail how to re-time your cam and then decided it would take me hours to type out the process and thought surely someone out there must have the steps and possibly even diagrams so I started searching the internet and found a few different instructional how too's. Several of them were missing steps/hard to follow or (based on my knowlege) way wrong. However I did find one with step by step instruction in detail with diagrams, and again based on my knowlege "a flawless how to" that was proper.

I know the instruction says its for the 4.6l however, the timing process is identical for the 5.4L (Windsor v8) nice motor by the way. So dont freak-

Jan 30, 2010 | 1988 Ford F 150

1 Answer

I have a 1965 food falcon with a mustang 302 (1978 ) v8. how do i know if it is a windsor or not?

Well there is a 302 cleveland, they are mainly an Australian engine. Identifying one is much like telling the difference between a 351 windsor and a 351 cleveland. Based on the fact that it's from Ford's 335 engine family. 8 cap screws to hold on the valve covers, the block is longer do to the timing chain housing being integrated. The fuel pump bolts are mounted vertically, and the exhaust bolt holes are diagonal. Also, a big difference between an american 302 and an aussie 302 cleveland, is the connecting rods for the cleveland are 6.000''. Where the american 302 connecting rod length is 5.090". Also, referring to a 302 as a windsor is incorrect, it's block families name is the 90 degree v8. The only engine in that family that is properly named the windsor, is the 351 windsor. The 90 degree family also includes the 302 boss. The boss has cleveland style heads, and the block has screw in freeze plugs.

Nov 27, 2009 | 2005 Ford Futura

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides