Question about 2000 GMC Jimmy

2 Answers

2000 Jimmy Liftgate - Glass Won't Open

Hi! I've found so much useful info on the subject. I have the repair clips I need to replace so that the glass will open. My problem is getting the trim open. Is there a trick to it? I've tried for 5 days now to try to pull it back so I can get to the release latch. It was supposed to be a surprise for my husband when he got back from the field next week =( It just goes back a little, and I can't get to the latch. Hell...I am not even sure exactly what the latch looks like that I have to get to. I've tried everything...even down to sending a hanger in there to try to hook something. If I can get the trim back so I can see...I'm sure I'll be able to find the latch. Please...is there anyone out there who has some advice for me as to how to get the trim to budge????

Posted by on

  • Melissa Zimmerman Jun 22, 2009

    Thanks guys. Yes a, I am talking about the inside. I did take off the handle already. I'll give it a shot and update you tomorrow. =)

  • Melissa Zimmerman Jun 23, 2009

    You guys are the best. I did it. My husband is going to love it! Thank you. I had some of these hooks lying around and used them to pry the plastic back without a break =)

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • GMC Master
  • 3,854 Answers

Just pull back on the panel after you remove the handle being held on by two screws, sorry if the panel breaks. But you can pick another tail gate panel at the Salvage yard for $20.00. After removing the handle you should have enough room to get to the c type latch, it's spring loaded and moves only one way to release the window. After that i am sure you can handle the rest. Keep me posted, be glad to help if you need more information. Good luck and hope this works for you. 

Posted on Jun 22, 2009

  • Harvey N Tawatao
    Harvey N Tawatao Jun 23, 2009

    Glad to put a smile on your face, be safe freind. 

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Check for screws behind little buttons you can pop out with a flat head screw driver. are you talkin about interior or exterior

Posted on Jun 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Envoy hatch lock


There is a known TSB for this....
#07-08-52-003: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE)/Key Fob Transmitter/Door Lock Switch, Lifgtate Hatch or Liftgate Glass May Lock/Unlock When Rear Liftgate Glass Button Depressed - (Sep 13, 2007)


Subject: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE), Key Fob Transmitter or Door Lock Switch, And/Or Liftgate Hatch Or Liftgate Glass May Lock Then Unlock When Rear Liftgate Glass Button is Depressed (Reposition Lock Cylinder Wave Washer and Adjust Lock Rod)


Models: 2005-2007 Buick Rainier

2005-2008 Chevrolet TrailBlazer, TrailBlazer EXT, TrailBlazer SS

2005-2008 GMC Envoy, Envoy XL, Envoy Denali

2005-2008 Saab 9-7X




--------------------------------------------------------------------------------
Do This
Don't Do This

Reposition liftgate lock cylinder wave washer and adjust lock rod.
DO NOT replace the liftgate latch or actuator.


Condition
Some customers may comment on one or more of the following conditions:

• The rear liftgate glass may not lock when using the remote keyless entry (RKE), key fob transmitter or door lock switch unless the lock is pressed a second time.

• The rear liftgate or glass locks, but may be unlocked when the rear liftgate lock cylinder button is depressed.

• The rear liftgate locks but the liftgate glass may not lock.

Cause
These conditions may be caused by one or all of the following:

• The rear liftgate cylinder lock rod may be out of adjustment.





• The wave washer on the liftgate lock cylinder may be out of position with the cup side down.

• Excessive movement or slack in the lock rods at the liftgate bell crank assembly.





• The liftgate lock cylinder pawl may contact the rear liftgate glass latch when the lock cylinder button is depressed.

Correction
Important: Do Not remove the rear liftgate lock cylinder from the vehicle to perform this repair.

Reposition the rear liftgate lock cylinder wave washer and adjust the lock rod using the steps below.

Verify the customer's condition.

Open the liftgate.

Remove the upper liftgate garnish molding.

Remove the rear liftgate trim panel.

Remove the cylinder lock rod from the threaded lock rod retaining clip.

Tip
Place the tip of a screwdriver blade into the opening of the C-clip and slowly rotate the screwdriver to pry out the C-clip from the shaft. Then use needle-nose pliers to remove the C-clip.

Remove the C-clip from the rear liftgate lock cylinder push button and remove the wave washer.

Install the wave washer with the cup side up.

Position the wave washer with the curved edges of the wave spring parallel to the tabs on the lock cylinder shaft.

Important: Use needle-nose pliers to slightly squeeze the C-clip back into shape. Make sure the clip seated, you should feel a snap and hear an audible click.

Install the C-clip onto the shaft and in the slot using needle nose pliers. Then rotate the pawl several times to make sure the C-clip does not rotate. If the clip rotates then the clip is not fully seated.

Position the lock cylinder pawl to the full clockwise position.

Pull up on the cylinder lock rod to remove any slack in the bell crank.

Install the cylinder lock rod into the threaded lock rod retaining clip while removing any slack from the lock rod linkage.

Close the lock rod retainer clip.

Close the liftgate assembly.

Open the liftgate glass while keeping the liftgate closed.

Use the key fob to cycle the liftgate to the lock and unlock position while inspecting the rear liftgate pawl. The lock cylinder pawl should have clearance between the latch as shown above. If the pawl is contacting the latch, readjust the cylinder lock rod.

Verify that the customer's condition has been corrected.

Install the rear liftgate trim panel.

Install the upper liftgate garnish molding.

Apr 14, 2014 | GMC Envoy XL Cars & Trucks

1 Answer

2000 Mercury Mountaineer rear liftgate handle is broken, how can I open it?


either crawl into back or if u have split gate where window opens u have to remove the little plastic access cover {on rear panel}and in the hole push against the rod to open ...once opened u can remove the rear panel and lube and or repair the clips that actuate the lock and release rods

Jan 05, 2013 | 2000 Mercury Mountaineer

1 Answer

Rear liftglass won't lock


#07-08-52-003: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE)/Key Fob Transmitter/Door Lock Switch, Lifgtate Hatch or Liftgate Glass May Lock/Unlock When Rear Liftgate Glass Button Depressed - (Sep 13, 2007)


Subject: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE), Key Fob Transmitter or Door Lock Switch, And/Or Liftgate Hatch Or Liftgate Glass May Lock Then Unlock When Rear Liftgate Glass Button is Depressed (Reposition Lock Cylinder Wave Washer and Adjust Lock Rod)


Models: 2005-2007 Buick Rainier

2005-2008 Chevrolet TrailBlazer, TrailBlazer EXT, TrailBlazer SS

2005-2008 GMC Envoy, Envoy XL, Envoy Denali

2005-2008 Saab 9-7X




--------------------------------------------------------------------------------
Do This
Don't Do This

Reposition liftgate lock cylinder wave washer and adjust lock rod.
DO NOT replace the liftgate latch or actuator.


Condition
Some customers may comment on one or more of the following conditions:

• The rear liftgate glass may not lock when using the remote keyless entry (RKE), key fob transmitter or door lock switch unless the lock is pressed a second time.

• The rear liftgate or glass locks, but may be unlocked when the rear liftgate lock cylinder button is depressed.

• The rear liftgate locks but the liftgate glass may not lock.

Cause
These conditions may be caused by one or all of the following:

• The rear liftgate cylinder lock rod may be out of adjustment.





• The wave washer on the liftgate lock cylinder may be out of position with the cup side down.

• Excessive movement or slack in the lock rods at the liftgate bell crank assembly.





• The liftgate lock cylinder pawl may contact the rear liftgate glass latch when the lock cylinder button is depressed.

Correction
Important: Do Not remove the rear liftgate lock cylinder from the vehicle to perform this repair.

Reposition the rear liftgate lock cylinder wave washer and adjust the lock rod using the steps below.

Verify the customer's condition.

Open the liftgate.

Remove the upper liftgate garnish molding.

Remove the rear liftgate trim panel.

Remove the cylinder lock rod from the threaded lock rod retaining clip.

Tip
Place the tip of a screwdriver blade into the opening of the C-clip and slowly rotate the screwdriver to pry out the C-clip from the shaft. Then use needle-nose pliers to remove the C-clip.

Remove the C-clip from the rear liftgate lock cylinder push button and remove the wave washer.

Install the wave washer with the cup side up.

Position the wave washer with the curved edges of the wave spring parallel to the tabs on the lock cylinder shaft.

Important: Use needle-nose pliers to slightly squeeze the C-clip back into shape. Make sure the clip seated, you should feel a snap and hear an audible click.

Install the C-clip onto the shaft and in the slot using needle nose pliers. Then rotate the pawl several times to make sure the C-clip does not rotate. If the clip rotates then the clip is not fully seated.

Position the lock cylinder pawl to the full clockwise position.

Pull up on the cylinder lock rod to remove any slack in the bell crank.

Install the cylinder lock rod into the threaded lock rod retaining clip while removing any slack from the lock rod linkage.

Close the lock rod retainer clip.

Close the liftgate assembly.

Open the liftgate glass while keeping the liftgate closed.

Use the key fob to cycle the liftgate to the lock and unlock position while inspecting the rear liftgate pawl. The lock cylinder pawl should have clearance between the latch as shown above. If the pawl is contacting the latch, readjust the cylinder lock rod.

Verify that the customer's condition has been corrected.

Install the rear liftgate trim panel.

Install the upper liftgate garnish molding.

Jan 17, 2012 | 2009 Saab 9-7X

1 Answer

Liftgate Release Not Working on a 2000 GMC Jimmy


plug on inside panel of lift gate remove plug and use screwdriver to push on release use light in plug hole

Sep 08, 2017 | 2000 GMC Jimmy

1 Answer

When i use the key fob to lock the doors the back glass dont lock, ???????


This solution applies to models:
2002-2007 Chevrolet Trailblazer, Trailblazer EXT and Trailblazer SS
2004-2007 Buick Rainier
2002-2007 GMC Envoy, Envoy XL, and Envoy Denali
2002-2004 Oldsmobile Bravada
2005-2007 Saab 9-7x

Condition/Concern:
Rear liftgate glass will not lock when using the key fob or door switch unless the lock button is pressed a second time. All other doors will lock normally. This could be the result of the liftgate glass lock rod not adjusted correctly. This lock rod travels from the liftgate lock actuator to the glass release push-button cylinder.

Recommendation/Instructions:
Remove the inside rear liftgate trim panel. Disconnect the threaded lock rod clip at the end of the push-button glass release and rotate this clip 1 complete turn at a time making the lock rod longer. This will be the only threaded lock rod visible when the trim panel is removed and the liftgate is raised.
Note: For the rear glass to release, the rear liftgate latch must be in the closed position. For test purposes only, this latch can be made closed to make this lock rod adjustment.

Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.

Apr 25, 2010 | 2006 Chevrolet Trailblazer

1 Answer

I'm having a similar problem with a 1997 GMC Jimmy. The glass won't open on the liftgate. I tried what the manual says for emergency release but nothing works. Does anyone have a suggestion or a picture of...


After a while, the mechanism (actuator) that unlocks and releases the rear glass hatch in your Jimmy will eventually burn out. when it does, there is really no way to open the glass and lower the tailgate.
The only way to replace the burnt out actuator is to open the tailgate which you can't because the actuator is burnt out.

I've read stories that even the dealers don't know what to do, some have even cut up the back panel to reach the so-called manual release. Others said they pulled back the glued on carpet to search for it also.

Well if you don't want to hack up the tailgate panel or rip out your carpet, here's the easy way to open the glass:

You just pull back the interior tailgate panel right above the bump in the middle where the latch is. There are no screws or bolts in that area, you can safely pull it back about 2 inches. Then you'll have to stuck your finger in and push down the release bar.

When you get your finger back there, you should be able to feel for the part that need to be pushed down. When that part is pushed down, the glass has been unlocked.

When you get your finger back there, you should be able to feel for the part that need to be pushed down. When that part is pushed down, the glass has been unlocked.

Good luck and hope this helps, The actuator that needs to be replaced costs $58 from the dealer.

Nov 10, 2009 | 2000 GMC Jimmy

2 Answers

Rear tail gate will not open


how to i open a stuck lift garte on a ford winstar 2000 lock broken too

Jun 14, 2009 | 2001 Ford Escape

1 Answer

2001 Ford Escape Rear Hatch won't unlock


The liftgate consists of the following components:
  • liftgate door lock actuator
  • liftgate lock cylinder (if equipped)
  • liftgate window glass
  • liftgate window latch/ajar switch
  • liftgate window glass release handle
  • liftgate latch remote control which consists of the following component:
    • liftgate release handle
  • liftgate latch, which consist of the following component:
    • liftgate latch door ajar switch
Liftgate Latch Actuator Removal and Installation
  1. Remove the liftgate latch remote control. For additional information, refer to Liftgate Latch Remote Control in this section.
SECTION 501-14: Handles, Locks, Latches and Entry Systems 2001 Escape Workshop Manual
REMOVAL AND INSTALLATION Liftgate Latch Removal and Installation
  1. Remove the liftgate trim panel.
  1. Disconnect the liftgate ajar switch electrical connector.
  1. Disconnect the liftgate latch actuating rod.
    1. Open the clip.
    1. Disconnect the actuating rod.
  1. Remove and discard the liftgate latch bolts.
  1. Remove the liftgate latch.
  1. NOTE: Make sure the liftgate latch release rod is not preloading the latch. It should be clipped in a relaxed state with no slack.
    NOTE: Position the liftgate latch release rod by pushing outboard to remove the slack.
  1. Remove the screws and the liftgate latch actuator
90f640f.gif

May 29, 2009 | 2001 Ford Escape

1 Answer

Open glass of liftgate 2000 jeep grand cherokee


there is a button outside on the liftgate where the licence plate light is . push button up to open glass

Apr 24, 2009 | 2000 Jeep Grand Cherokee

3 Answers

1995 Jimmy 4d 4wd rear lift gate will not open -


I was able to get two wedges between the glass and the plastic trim. From that I used a scope to see inside and find the mechanism to release the window. Look for the one piece of plastic in the mechanism. The level has to be pushed toward the driver side of the car. Once I got the glass open, I removed the handle, and two screws from each side of the trim and removed the trim.

Once the trim was removed I had a small opening and could see the problem. The end of the latch has a small blue plastic (why plastic??) catch that broke.

Rather than taking the door apart and finding a replacement, I heated a screw driver and made a slot in the plastic. Next I used a heavy duty zip tie and connected the two pieces (plastic catch and metal part that opens the latch). I left some slack in the connection and all works great.

Not sure how long this will last, but for now I have the back opening. I will look at replacing the plastic piece, but not sure if a total new mechanism is needed.

Stan

Nov 06, 2008 | 1995 GMC Jimmy

Not finding what you are looking for?
2000 GMC Jimmy Logo

240 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...