Question about 2000 Mercury Mountaineer

1 Answer

Door actuator need diaagram 2000 mercury mountaineer

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Mercury Master
  • 4,376 Answers

#3 is door lock actuator

door actuator - 3b2e243.gif

Posted on Jun 22, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Location of passenger side blend door actuator on 2006 mercury mountaineer auto controls, 6 cylinder

Temperature Blend Door Actuator - RH, EATC Removal and Installation
  1. Remove the RH floor console finish panel.
  1. Lower the glove compartment.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  2. Remove the 3 RH temperature blend door actuator screws.
    1. Remove the RH temperature blend door actuator.
2006 2010 Ford Explorer NO Heat Passenger Temp Actuator Replacement same as mountaineer

Jun 19, 2017 | Mercury Cars & Trucks

1 Answer

Where is blender door actuator fuse for ac/heat?

It is Fuse # 10 in the fuse panel on the drivers side of the dashboard.You need to open the door to see it.(the fuse panel ) The fuse should be a 7.5 amp fuse. Good luck !

Jul 02, 2014 | 2000 Mercury Mountaineer

1 Answer

99 mercury mountaineer door opens but won't lock on driver side. all other doors lock. What can be wrong?

The lock actuator is broken. Seems as if it went out in the unlock position. So you cant lock it. Replace the actuator and you will be able to lock it again.

Mar 07, 2014 | Cars & Trucks

1 Answer

I hear clicking when i turn on my heat. 2002 Mercury Mountaineer

This should be a faulty blend door actuator inside the dash. Depending on if its the left or right actuator you may have to remove the dash to gain access.

Mar 16, 2010 | 2002 Mercury Mountaineer

1 Answer

Driver sode door lock

The locking solenoid may need to be replaced, or the rod adjusted.
You will need to remove the door panel to watch the movement.
If the solenoid is not fully extending, it will require replacement.
It will look similar to this...
In the picture below, it will be #4

47cdcd4.gif Check the locking mechanism is lubricated properly. Try spraying some penetrating oil in the mechanism (just above 3 in the diagram) Wait 10 minutes, and re-try.
If the actuator does not fully extend, it will need to be replaced.

Jan 15, 2009 | 2001 Mercury Mountaineer

1 Answer

Garage door remote

I have a problem i just brought a 2000 Mercury Mountaineer in full.That nite picked up from dealer there's a squeaky noise on the front end.i turn corner and backing up the truck feels like gunna break down.It's like the bumps on side the thru way it shakes the truck.had taken it in to get fix got it back it still does it n now can hear lite tapping in the motor.i need a
solution. scared too have my son in the truck ridin with me.

Jun 30, 2008 | 2000 Mercury Mountaineer

Not finding what you are looking for?
2000 Mercury Mountaineer Logo

Related Topics:

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

gerry bissi

Level 3 Expert

4376 Answers


Level 3 Expert

81400 Answers


Level 3 Expert

5687 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides