Question about 2006 Mazda 5

1 Answer

Would like to change the sparkplugs on my 2006 mazda 5 but...

Where are the sparkplugs? Can a do-it-yourself guy do this without getting a headache?

Posted by on

  • jeannettebla Jun 22, 2009

    But where are the sparkplugs located on the Mazda 5 4 cylinder?



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 57 Answers

If all the plugs are easy to get at sure
use a piece of rubber hose to get each plug started in the hole so you do not cross thread them and make sure that you gap them properly with a gauge first

Posted on Jun 22, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I have a 2008 Mazda 5 minivan how do I change the headlight bulb

Headlight Change 2006-2010 Mazda 5 - CarCareKiosk
This free video shows how to change a burnt out headlight on a 2009 Mazda 5 Sport 2.3L 4 Cyl.. Complete instructions for replacing a head light bulb on a 2009 ...

Low beam head light bulb replace 2000-2006 Mazda Mpv ...

? 5:11
Jun 29, 2013 - Uploaded by hp11208
Low beam head light bulb replace 2000-2006 Mazda Mpv .... My step dad and I successfully replaced a headlight yesterday! :-) ...I've lost it trying to replace the bulb. if anyone can let me know I would really appriciate it thanks ! ..... 5:00. Cleaning your IAC to fix rough idle on 2000 or 2001 Mazda MPV ...

Nov 29, 2015 | Mazda Cars & Trucks

1 Answer

How do I change the ECT sensor on a 2006 Mazda 3 ?

I think they are located in between sparkplugs 3 and 4 and are accessible by removing the gromit that the wiring goes through. You need to flick the wiring plug off with a small screwdriver then you can get to the sensor with s socket and extension.

Let me know if this helps

Dec 31, 2012 | 2006 Mazda 3

1 Answer

Mazda 5 blower motor

You have to go to your dealer, because they need to remove the dash to change the blower.

Sep 16, 2012 | 2006 Mazda 5

1 Answer

2007 mazda 5 P2195 and p0131 after change o2 sensor one

I have the same problem on my 2006 mazda5. I go a new O2 sensor. Now I get p0131 and p2096 codes

Apr 10, 2012 | 2007 Mazda 5 2.3

1 Answer

I have a 2005 mazda 3 and I think that the starter is buisted how can I fix this without going to a shop?

easy answer, you can't..
You may be able to get a second hand unit and then remove your existing starter and fit the replacement but I would NOT advise you to disassemble the starter motor yourself.
There are parts inside the motor (bushes and brushes) that will be damaged by incorrect disassembly. The springs which maintain contact between the brushes and the commutator can (and do) pop out and disappear into the wide world and replacing them can prove difficult.
The solenoid WILL be damaged if you attempt to disassemble it incorrectly and some solenoids have several small parts which will fly out and end up in the same place as the brush springs, the same place socks, earings and loose change go to.. the land of nowhere.
So, either change the starter yourself or bite the bullet and take the starter to a qualified person..
Remember, if you really want to remove the starter yourself, disconnect the negative battery cable at the battery BEFORE you do anything else..

Dec 19, 2010 | 2006 Mazda 3

2 Answers

Cant find sparkplugs

The spark plugs are under the aluminum engine cover plate on the top of the engine. ( The one that has the raised ribs and has the 2.4 on it) You need to remove the 4 bolts that hold the plate on the engine and then you will see the spark plugs in the center of the head in between the cam towers. Once you get the plate off, you can't miss them.

May 31, 2009 | 2001 Pontiac Grand Am SE

3 Answers

How to fix and clean the mazda 5 diesel

You can clear these if less than 60% blocked by giving the car a good blast on the motorway going through the revs. If your car is on limp mode you do need to replace the particulate filter as the blockage is too much to regenerate. I have found a company that does these very cheap and are technicly brilliant i had many questions and they seemed to answer correctly with confidence. They supplied the part to me for £500, i have checked from this for the automotive solutions guys that did it for £450 but couldnt find them which is why i went with these. The company is and i spoke to someone Called Darrell. There number is anyone wants it is 0844 880 4149 he did giv me a direct number but im sure he wouldnt want me to list that on here as its his work mobile.

Mar 09, 2009 | 2006 Mazda 5

2 Answers

Mazda 5 replacing external handle on sliding door

Your door should be held on with clips. Removing the panel is sometimes hard, just take a good WIDE flat head screwdriver, and whatever tool needed to remove the screws holding the panel on, and be careful. Check underneath the panel, by the inside handle, and the arm point for screws. Once removed, take your WIDE screw driver, and don't quite pry them off, more or less try to get it underneath and pull towards yourself. There is no real easy way, just try to be patient with it, and if you hit any binds, look for more screws, its just a matter of patience for sure.

Feb 13, 2009 | 2006 Mazda 5

1 Answer

Mazda mx5 1990

The thermostats on Mazdas are notorious for kicking out and causing the fans to either not initiate or go on without effective results. My Protege went through 3 before I got my Miata, and I learned how to change the thermostat when it went out the first time. Hopefully, there won't be a second time, but whenever the car overheats and I notice the fans don't come one, I always assume it's the thermostat, and that's always the cause. If you don't want to fix it yourself, take it to a dealer, they're very accustomed to changing thermostats in Mazdas, believe me.

Aug 27, 2008 | 1999 Mazda MX-5 Miata

3 Answers

Keyless entry remote

there should be a black box under the dash assosiated to the keyless entry you need to open it and there should be two pins next to each other you need to arc them together with a screwdriver you should see the blinkers flash then without releasing the screw driver press the button on the remote pad repeat this for the other remote

Jun 22, 2008 | 2006 Mazda 5

Not finding what you are looking for?
2006 Mazda 5 Logo

Related Topics:

260 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

82285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides