Question about 2002 Mercury Mountaineer

1 Answer

What tools are needed to change front brakes on 2000 mountaineer

I need to change my fornt brakes...what tools are need to to remove calipers

Posted by on

  • yadayada
    yadayada May 11, 2010

    common hand tools

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 365 Answers

A set of Torx bits between 12MM-24MM, a 10" C-clamp and a couple cans of "BrakeKLeen" available at most auto parts stores. I would have a SAE set of sockets available as well with 3/8" drive and extensions. A nice big straight screwdriver too! These vehicles are pretty notorious for bad rotors...be prepared to just replace them <$50 ea. they CANNOT be turned.

Posted on Jun 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i compress the caliper piston back of audi a6 2000 2.8l awd what kind of tools i need . Vise grip is not working.


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also.
But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!

For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!!

Check brake fluid level and top up if neccessary!!!

Oct 26, 2011 | 2000 Audi A6

1 Answer

Remving caliper pins on 2000 vw jetta and caliper


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Jun 26, 2011 | 2000 Volkswagen Jetta TDI

1 Answer

What tools are needed to change the brakes


if the front are rotors there are two bolts that need to be taken off first.
remove the caliper, then remove the two caliper bracket bolts and remove the rotor
replace the rotor and reinstall the caliper bracket.
pull the caliper sliders and lube them with brake grease.
reinstall caliper sliders and install new pads and caliper
refasten caliper to bracket and your done

if your doing rear disc brakes same as front
if brakes are drum type you will need rear drum brake tools to release the springs and to refasten
the new brake shoes

Jan 15, 2011 | 1996 Buick Century

1 Answer

I need to change the front brakes on a 2001 BMW Z3 3.0...any special tools required for that? I've done lots of brake jobs, but never on a beamer...thanks!


NOPE NO SPECIAL TOOLS JUST REMOVE BRAKE PAD WEAR INDICATOR CONNECTOR.REMOVE THE CALIPER GUIDE BOLTS AND THE SPRING CLAMP.TURN UP THE CALIPER AND REMOVE THE BRAKE PADS.THE INNER PAD IS LOCATED WITH A SPRING IN THE PISTON.

Oct 25, 2010 | 2000 BMW Z3

1 Answer

WHAT TOOLS ARE NEEDE TO REPLACE AUDI A3 SPORTSBACK FRONT BRAKE PADS


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. You must buy the brake pads with wear sensor. For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exists, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Feb 14, 2010 | 2006 Audi A3

1 Answer

Replace front brake pads


Losen your lug nuts on both front tires and jack up the front end. You need to remove the calipers (the piece that holding the brake pads) Two bolts behind the caliper. Pop the the brake pads off and depress the brakes ( you will need a clamp to depress it) Put on the new brake pads. Tools needed : clamp, flat head screww driver, soket set, brake cleaner

Jan 20, 2010 | 2000 Hyundai Accent

2 Answers

Successfully changed front brakes but when i went to change rear brakes the caliper seems to be stuck.what can i do?


your rear brake has most likely a drum in hat style brake.

The caliper is not stuck, you need a special tool to rotate the piston of the brake caliper and depress it down. It is connected to your parking brake, that is why this security measure was taken.

the special tool looks like this :

9d6f12d.gif

a ratchet fits in the center hole and depending on the style of piston you have you will need a specific side of this "cube" tool.
you may need to slide the pads out to see the piston.

I hope this helps, Goodluck!

May 11, 2009 | 2000 Lincoln Continental

4 Answers

Replace rear brake pads on a 2000 grand marquis


rate as fixya if this is what you need. Thanks

  1. Remove the rear disc brake caliper (2K327).
  2. Remove the brake caliper bolts.
  3. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2B582).
  1. sya~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pads.
    Remove the brake pads by pushing inward and rotating the pad up.
  1. NOTE: Use a block of wood or used pad to protect the piston and boots.
    Retract the caliper piston (2196) into the rear disc brake caliper.
cf7b02c.gif

Mar 15, 2009 | 2000 Mercury Grand Marquis

1 Answer

How to change front break pads A4 2000 and what type/ make of pads do i need


I have the same car 2000 Audi A4. I recommend you "TRW" brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. (On my car y have 288 mm). After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow: 1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose! 2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper. 3. Now you must thoroughly clean the brake calipers (free of grease). 4. Remove outer brake pad from brake carrier. 5. Pull inner brake pad out of brake caliper piston. 6. Check up the brake fluid level on the reservor, and emptying if neccessary! 7. Push piston back into brake caliper housing. 8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward). 9. Install outer brake pad into brake carrier. 10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm. 11. Install both caps. 12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!! Please Rate my Response! Thanks!

Mar 02, 2009 | 2000 Audi A4

Not finding what you are looking for?
2002 Mercury Mountaineer Logo

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...