Question about 2001 Saturn SC

1 Answer

Wheel hub bearing casing still inside how to get it out?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 520 Answers

Those bearing races are pressed in the hub...they can be driven out with a fairly long punch and a hammer...preferrable a 4 lb hammer/sledge and failry large pin punch or chisel

Posted on Jun 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How can I remove rear outer bearing?


New style bearings are all pressfit bearings, if your hub came right out of the bearing assembly, it is time for the whole assembly. The hub assembly has a locking ring that holds the outer bearing race inside the hub, after the wheel hub has been pressed out. Then, after the lockring has been removed it can be pressed out and the new bearing can be pressed back in and then the lockring reinserted. Then the wheel hub gets pressed in.

Mar 05, 2016 | 2002 Kia Sportage

1 Answer

What is the foot pounds for the front wheel bearings on a 1995 chrysler cirrus


Hello, If you Chrysler has replaceable wheel bearings and seal. This is the way it goes---pack the wheel bearing with new grease-install the bearing in the wheel nub--install new back wheel seal--coat the axle shaft with grease lightly, thing coat-----install wheel hub on to axle shaft...be careful here don't damage the rear hub seal------------insert front race washer---install axle shaft nut--tighten nut down wheel nut until it is firm with water pump pliers----spin the hub/with tire mounted.
(the wheel and hub will turn but not freely)----take the pliers and back off the axle nut 1/4 turn----now spin the wheel and axle hub, it should spin freely---now if doesn't spin freely---back off the axle nut about 1/16 or 1/32 (or just a little bit)-----now, spin the wheel and hub and if turn freely------------Now grab the top of the wheel/tire and move it back and forth.-----if there is some movement ---try tighten the axle nut just a little little bit, unit the one can barely feel some little movement in the wheel/tire and hub.-----------Now, spin the wheel/tire and hub and it should also turn freely.

If it does----install new and correct size of cotter pin and bent the ends around the axle nut.----

coat the inside of the hub cup with grease. Now, use an rubber or plastic hammer to install the cup on the wheel/tire hub. You are finished with one wheel bearing maintenance. Now do the other side.



I really don't know if you Chrysler Cirrus has replaceable wheel bearing. All the auto/trucks have replaceable hubs, that means that the replacement is total hub with axle shaft, sealed bearings, and seals. This is bolt to each wheel steering hub. This work to remove these one unit hubs.

Four bolts hold the axle hub to the steering hub. Hear is the problem!! it has rusted to the steering hub. Also, these hubs cost more than replacing bearings, races, seals to cool turn of $180 to $250+ I wish you luck in your replacement of wheel bearing on your Chrysler. GB..stewbison

Sep 24, 2011 | Chrysler Cirrus Cars & Trucks

1 Answer

How to change back hub on 97 cr-v


Rear Brake Discs
  • Fotolia.com" data-type="modal">honda-rear-wheel-bearing-removal-1.1-800x800.jpg Replace the bearing and race as a single set. automotive roller bearing. image by Tom Oliveira from Fotolia.com

    Before raising the rear of your Honda, remove the dust cup from the center of the brake drums using a hammer and chisel. This will give you access to the spindle nut, which you can loosen using an axle nut socket. Then you can raise and remove the wheel/tire assembly ,or assemblies if you are replacing the bearings on both wheels.

    If your Honda model is equipped with rear disc brakes, remove the brake disc retaining screws, the brake hose bracket from the steering knuckle and caliper bracket mounting bolts. Hang the caliper to the coil spring using wire. Do not let the caliper hang free or the brake hose may be damaged.

    At this point, you will be able to remove the brake disc by hand. However, rust may have a firm grip on the disc. If this is the case, use a couple of 8-by-1.25 mm bolts and screw them evenly into the brake disc threaded holes. This will push the disc off the hub. Now you can finish removing the spindle nut and hub/wheel bearing assembly and install the new hub/wheel bearing assembly using a new spindle nut



Read more: Honda Rear Wheel Bearing Removal ' eHow.com http://www.ehow.com/way_5974291_honda-rear-wheel-bearing-removal.html#ixzz1W3WDRoqv Rear Brake Drums
  • Fotolia.com" data-type="modal">honda-rear-wheel-bearing-removal-2.1-800x800.jpg Pack the bearing with bearing grease before installation. roller bearing image by Tom Oliveira from Fotolia.com

    If your Honda Civic comes equipped with rear brake drums, remove the center grease cup and loosen the axle spindle nut using an axle nut socket. After raising and removing the wheel/tire assembly, finish removing the axle nut and washer.

    You might be able to remove the outer wheel bearing from the spindle using a screwdriver. If not, wiggle the brake drum as you pull on it to let the bearing fall off the spindle. However, the brake drum might be caught in place by the brake shoes. In this case, you can retract the brake shoes through the hole in the back of the backing plate.

    Remove the rubber plug from the back of the backing plate. Then rotate the star wheel on the adjusting screw using a brake adjusting tool as you push the lever off the start wheel with a screwdriver. With the brake shoes off the brake drum, pull the brake drum off the wheel assembly. Then clean the brake assembly with brake parts cleaner and a clean, lint-free towel.

    Now you can set the brake drum on a workbench or hard surface and remove the grease seal and inner wheel bearing. The inner and outer wheel-bearing races can be removed using a drift punch and hammer. Pack the new wheel bearings with high-temperature wheel-bearing grease using a wheel-bearing packer and use a new grease seal during installation. Also, before reinstalling the brake drum, apply a thick coat of wheel-bearing grease to the cavity inside the hub, but do not fill it completely.



Read more: Honda Rear Wheel Bearing Removal ' eHow.com http://www.ehow.com/way_5974291_honda-rear-wheel-bearing-removal.html#ixzz1W3WN9eBb

Aug 25, 2011 | Honda CR-V Cars & Trucks

1 Answer

How do you remove front wheel bearing from a 2007 Toyota hiace van. Setup is not like an ordinary wheel bearing setup where you remove dust cap and securung nut at front of the wheel/


We don't live in the 1960's any more

Most vehicles have wheel bearing hub assy's

You remove ,in most cases 4 bolts from the back or
inside,that hold it onto the steering knuckle

First you remove the axle nut

Jul 23, 2011 | Toyota Xtracab Cars & Trucks

1 Answer

What is needed to remedy right hand front wheel bearing play on a 1990 d21 4X4 ute


replace the bearing or wheel hub assembly.

REMOVAL & INSTALLATION 2wd Models NOTE: Refer to wheel bearing service and bearing preload adjustment procedures found in Section 1.
  1. Raise the front of the truck and support it with safety stands. Remove the wheels.
  2. Remove the brake caliper and suspend it with wire, out of the way. Remove the caliper torque plate if equipped.
  3. Remove the dust cap and then remove the cotter pin, lock washer (if equipped) nut lock and nut.
  4. Pull the hub/disc assembly off the spindle with the outer bearing. Don't let the bearing fall out.
  5. Pry the inner oil seal out and remove the inner bearing. To install:
  6. Clean and inspect the bearings and outer races.
  7. Using a brass drift and a hammer, drive out the bearing outer race. Press a new one into position.
  8. Pack the bearings with grease until it oozes out the other side. Coat the inside of the hub and cap with grease.
  9. Position the inner bearing into the hub, coat the oil seal with grease and press it into the hub.
  10. Press the hub assembly onto the spindle and install the outer bearing and thrust washer.
  11. Install the hub nut. Turn the hub a few times to seat the bearings and then loosen the nut until there is 0mm axial play. Using a spring tension gauge, check that the preload (with new grease seal installed) is 2.2–6.4 lbs. (9.8–28.4N)
  12. Install the lock-nut, new cotter pin and hub grease cap.
  13. Install the brake torque plate. Install the brake caliper.
  14. Install the wheels and lower the truck.
4wd Models The hub and bearing service procedures for a 4wd models are basically the same as those for a 2wd version, with the exception of removing the free running hub assembly and the bearing preload adjustment. Refer to Sections 1 and 7 for additional information. Adjust the preload after the wheel bearing is replaced or the front axle assembly is reassembled. BEARING PRELOAD ADJUSTMENT
  1. Thoroughly clean all parts and pack the wheel bearings.
  2. Apply grease to threaded portions of the spindle, grease seal lip and wheel hub.
  3. Tighten the wheel bearing lock-nut with a socket and torque wrench to 58–72 ft. lbs. (78–98 Nm).
  4. Rotate the hub in both directions a few times to seat the bearings. Loosen wheel bearing lock-nut.
  5. Retighten the lock-nut to 0.4–1.1 ft. lbs. (0.5–1.5 Nm).
  6. Turn wheel hub several times in both directions.
  7. Retighten the lock-nut to 0.4–1.1 ft. lbs. (0.5–1.5 Nm). Fig. 1: Exploded view of the front axle assembly — 2wd models 86718030.gif
    Fig. 2: Removing the bearing outer races 86718032.gif
    Fig. 3: Packing the wheel bearing with grease 86718033.gif
    Fig. 4: Pack the lip cavity of grease seal with grease 86718034.gif
    Fig. 5: Exploded view of the front axle assembly — 4wd models 86718031.gif

  8. Measure wheel bearing axial end-play. The wheel bearing end-play specification is 0.
  9. Install lock washer by tightening the lock-nut within 15–30 degrees.
  10. Turn wheel hub several times in both directions. Wheel bearing should be seated correctly.
  11. If necessary, measure wheel bearing preload. NOTE: Measure wheel bearing preload with a spring-type gauge; measure at wheel hub bolt, with tire removed. The hub assembly should rotate with 1.6–4.7 lbs. (0.73–2.13 kg) of pressure.
prev.gif next.gif

Jul 28, 2010 | 1991 Nissan Pickup

1 Answer

Cv axle 4x4 diferencial


Make sure 2- wheel drive is selected.
Jack up the vehicle front and support on axle stands. Remove the wheel.
Remove the brake caliper. It bolts onto the hub carrier(aka knuckle) with 2 bolts from the vehicle side of the carrier so you cant see them without sticking your head into the wheel arch. Slide the caliper off the rotor and hub and hang it with a piece of wire inside the wheel arch. Dont let it hang on the pipe it is connected to. The caliper may be difficult to remove if the rotor has a ridge on its outer edge due to wear.
Remove ABS speed sensor(2 bolts to remove) behind the hub
Next comes the hub assembly. :
  • Shift on the fly:Remove 6 bolts on the cap then the cap itself. Next the snap ring/circlip and the shim behind it.(On the piece of shaft now visible) and then you can pull off the hub flange. Remove the screw on the lock washer and then the washer itself. Remove the hub nut.The hub assembly(with rotor) will now pull off the shaft. Remove inner bearing and oil seal.
  • Manual hub: Select transmission 2H and "Free" on the hub. and run the vehicle about 100 m/300 ft.Remove 6 bolts on the cap then the cap itself. Next the snap ring/circlip and the shim behind it. Remove body assembly.
Remove the bottom ball joint on the hub carrier.(Ball joint removal tool may be needed to free the ball joint. Dont go hammering it. That will damage the thread) Swing the carrier upwards and you should have just enough free space to pull the shaft from the hub carrier. If not remove the top balljoint as well. Remove the clamp/SS strip from the inner CV rubber boot. Pull the boot back on the shaft. Remove the circlip from inside the DOJ case. The shaft can now be pulled from the DOJ case.
Remember to preload the wheel bearing on reassembly. Tighten the hubnut to 29 N.m. then loosen fully. Tighten again by hand. Connect a spring scale to the wheel stud. Pulling on the scale in the direction of rotation should give a reading of 2-2.5 kg/4.4-5.5 lb(new bearing) or 1.2-1.8kg/2.6-4 lb(used bearing) when the rotor starts to move. If it does not, tighten the hub nut a littl and measure again. Repeat till the correct measurement is achieved. See diagram.

2924189.jpg

Jul 21, 2010 | 1999 Isuzu Trooper

2 Answers

I would like to know if the wheel bearing is in the shaft or the hub?


The Constant Velocity (CV) joints are located on the inner and outer edges of the axle shaft. The axle shaft runs through the hub and bearing in the spindle.

Jun 16, 2010 | 1999 Daewoo Nubira

1 Answer

How do i remove the rear wheel hub so i can replace the worn out wheel bearing


hi from uk to remove rear hub/s you have to remove the bolts that secure the hub and brake backplate to th axle these hubs come complete with bearing and is not normally the case of replacing the actual bearing ? and this type of hub is becoming common fitting on lots of vehicles like hyundai/ford/vauxhall etc hope this helps ?

Feb 22, 2010 | 2002 Hyundai Accent

2 Answers

How can you tell if the front hub assembley needs changed. There is a loud noise that gets louder as you pick up speed. I was told it was the front wheel bearing but there is no wheel bearing just the...


There is a wheel bearing inside the hub as well. They will sell those bearings I've bought them before. Chances are you need to talk to a better parts guy. You can tell if it's a wheel bearing by taking the vehicle up to a speed where the noise is clearly audible. Then swerve the vehicle back and forth in your lane. If the sound changes or goes away when you swerve, it's a wheel bearing. Obviously we're not trying to crash the vehicle here, so don't get over aggressive with the swerving.

Nov 12, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

Need instruction manual/schematics for replacing 2005 kia rio driver side rear wheel bearing. i've got the wheel/hub/bearing off, not the inside ring to the bearing. i need to know how to replace it .


clean all the grease if there is any out of the hub, turn the hub over and using a drift and hammer strike the shell from the back edge working around the shell as you go, should not take too much to remove it but you will need a bit more than a tap with the hammer.
Hope this has helped you

May 22, 2009 | 2003 Kia Rio

Not finding what you are looking for?
2001 Saturn SC Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...