Question about 1996 Buick Regal Olympic Gold

2 Answers

Wheel studs how to get the wheel studs off a 96 buick regal custom on passenger side?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 6,982 Answers

Nuts still on or broken off?

Posted on Jun 21, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 316 Answers

The studs are pressed into place. You can remove them and replace them using a vise, and a couple sockets (one larger, and one smaller). You do need to remove the "wheel hub" from the vehicle to perform the repair.

Posted on Jun 21, 2009

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 316 Answers

SOURCE: how to get the wheel studs off a 96 buick regal

Your question was answered. Read your email.

Posted on Jun 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change broken studs on a 96 buick regal front wheel


I assume you are talking about the ones that hold the tire on these ones are likely just pressed in and you should be able to hammer them out just be careful so you don't damage the wheel bearing. I would also test the wheel bearing and make sure it is good if it is bad you would be better off just replacing it a new wheel bearing should have all the studs in it.

Jul 26, 2015 | Buick Cars & Trucks

1 Answer

How to replace Serpntine belt on 2002 Buick regal 3.8l supercharged engine


its not a fun job,you will need to remove a spacer that is mounted between block and engine mount on front of engine.there are 2 belts on this motor.if your on the passenger side of car looking at engine its to the right of mount its a stud with nut then remove stud it is 15mm nut you will need a e40 or 45 to remove stud good luck,mike

Dec 26, 2014 | 2002 Buick Regal

1 Answer

96 buick regal, w/dual climate control, w/ac on blows hot air on driver side and cold air on the passenger side


It can be low on freon,or,the actuator motor foor that side blend door is bad,if so,the dash has to be removed to replace the actuator motor.

Jun 07, 2010 | 1996 Buick Regal Olympic Gold

2 Answers

Looking for rim specs for a 1999 Buick Regal GS. Specificly what is the measurement between the wheel studs for rim selection?


Take a steel rule of 6" or so and measure from the center of the wheel stud to the stud opposite of it. Since there are 5 in the circle, measure the distance between 1 and 3 and you will have the info you need.

Nov 20, 2009 | 1999 Buick Regal

3 Answers

I have a 1996 Buick Regal Custom. The blower motor quit working early this spring and I replaced it with a new one. It worked great for a while, but now it doesn't work when I set the switch to high. It...


Blower motor resistor. Its a special resistor attached to the blower housing near the blower motor. one wire clip and 2 screws usually is all that holds it in place.

Jul 20, 2009 | 1996 Buick Regal Olympic Gold

1 Answer

Replacing wheel studs on front of 1990 buick regal


take off the wheel and remove the axle. knock out the bad lugs and press new ones in with a big vise or shop press

Jun 24, 2009 | 1990 Buick Regal

1 Answer

How do u remove the wheel hub off a 96 buick regal custom?


if it has a lock on it thin you need a key but a Flathead should just fit in there to pop it off

Jun 21, 2009 | 1996 Buick Regal Olympic Gold

1 Answer

Powersteering on my 96 buick regal olympic edition


If your buick regal has the 3800 engine the power steering is located on the passenger side of the car about halfway down the back of the engine.

Mar 29, 2009 | 1996 Buick Regal Olympic Gold

1 Answer

Location of oil filter on buick regal 2000


passenger side under car near passenger front wheel behind a plastic splash shield. just bend it out of the way. When finished , put it back or it will rub on the tire.

Mar 27, 2009 | 2000 Buick Regal

Not finding what you are looking for?
1996 Buick Regal Olympic Gold Logo

Related Topics:

366 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...